Lines Matching full:on
63 … If oversampling is enabled on both regular and injected groups, this parameter
80 …MAContinuousRequests' and 'Oversampling': ADC enabled without conversion on going on group regular.
81 …rAutoWait' and 'DMAContinuousRequests': ADC enabled without conversion on going on groups regular …
84 * (which fulfills the ADC state condition) on the fly).
91 …Note: In case of usage of channels on injected group, ADC frequency should be lower than AHB clock…
93 … Note: In case of synchronous clock mode based on HCLK/1, the configuration must be enabled only
106 …gain compensation coefficient to be applied to ADC raw conversion data, based on following formula:
136 …Do use with polling: 1. Start conversion with HAL_ADC_Start(), 2. Later on, when ADC conversion da…
147 …Note: This parameter must be modified when no conversion is on going on regular group (ADC disable…
190 …: This parameter can be modified only if there is no conversion is ongoing on ADC groups regular a…
202 …'SamplingTime', 'Offset', 'OffsetNumber': ADC enabled without conversion on going on regular group.
203 …amplingTime', 'Offset', 'OffsetNumber': ADC enabled without conversion on going on regular and inj…
206 * on the fly).
212 …Note: Depending on devices and ADC instances, some channels may not be available on device package…
240 of another parameter update on the fly) */
246 uint32_t Offset; /*!< Define the offset to be applied on the raw converted data.
250 …Note: This parameter must be modified when no conversion is on going on both regular and injected …
255 …Note: This parameter must be modified when no conversion is on going on both regular and injected …
259 …Note: This parameter must be modified when no conversion is on going on both regular and injected …
268 …shold', 'LowThreshold': ADC disabled or ADC enabled without conversion on going on ADC groups regu…
269 …arameters 'HighThreshold', 'LowThreshold': ADC enabled with conversion on going on regular and inj…
280 …can be monitored by applying successively the AWD init structure. Channels on ADC group regular an…
284 …his parameter has an effect only if parameter 'WatchdogMode' is configured on single channel (only…
297 … impacted: the comparison of analog watchdog thresholds is done on
307 … impacted: the comparison of analog watchdog thresholds is done on
355 #define HAL_ADC_STATE_REG_BUSY (0x00000100UL) /*!< A conversion on ADC group regular is …
356 …external trigger, low power auto power-on (if feature available), multimode ADC master control (if…
357 #define HAL_ADC_STATE_REG_EOC (0x00000200UL) /*!< Conversion data available on group re…
359 #define HAL_ADC_STATE_REG_EOSMP (0x00000800UL) /*!< Not available on this STM32 series: E…
362 #define HAL_ADC_STATE_INJ_BUSY (0x00001000UL) /*!< A conversion on ADC group injected is…
363 …external trigger, low power auto power-on (if feature available), multimode ADC master control (if…
364 #define HAL_ADC_STATE_INJ_EOC (0x00002000UL) /*!< Conversion data available on group in…
500 …A_ALIGN_RIGHT)/*!< ADC conversion data alignment: right aligned (alignment on data register LSB bi…
501 …GN_LEFT) /*!< ADC conversion data alignment: left aligned (alignment on data register MSB bi…
596 /** @defgroup ADC_HAL_EC_REG_OVR_DATA_BEHAVIOR ADC group regular - Overrun behavior on conversion …
647 /* Note: VrefInt, TempSensor and Vbat internal channels are not available on */
668 …el connected to VrefInt: Internal voltage reference. On this STM32 series, ADC channel available o…
669 … internal channel connected to Temperature sensor. On this STM32 series, ADC channel available onl…
670 … internal channel connected to Temperature sensor. On this STM32 series, ADC channel available onl…
671 …ladder of factor 1/3 to have Vbat always below Vdda. On this STM32 series, ADC channel available o…
672 …< ADC internal channel connected to OPAMP1 output. On this STM32 series, ADC channel available onl…
673 …< ADC internal channel connected to OPAMP2 output. On this STM32 series, ADC channel available onl…
674 …< ADC internal channel connected to OPAMP3 output. On this STM32 series, ADC channel available onl…
675 …< ADC internal channel connected to OPAMP3 output. On this STM32 series, ADC channel available onl…
676 …< ADC internal channel connected to OPAMP4 output. On this STM32 series, ADC channel available onl…
677 …< ADC internal channel connected to OPAMP5 output. On this STM32 series, ADC channel available onl…
678 …< ADC internal channel connected to OPAMP6 output. On this STM32 series, ADC channel available onl…
775 …FLAG_AWD1) /*!< ADC Analog watchdog 1 event (main analog watchdog, present on all STM32 series) */
776 … /*!< ADC Analog watchdog 2 event (additional analog watchdog, not present on all STM32 series) */
777 … /*!< ADC Analog watchdog 3 event (additional analog watchdog, not present on all STM32 series) */
1343 /* Note: bit cleared bit by writing 1 (writing 0 has no effect on any bit of register ISR) */
1396 * (1) On STM32G4, parameter available only on ADC instance: ADC1.\n
1397 * (2) On STM32G4, parameter available only on ADC instance: ADC2.\n
1398 * (3) On STM32G4, parameter available only on ADC instance: ADC3.\n
1399 * (4) On STM32G4, parameter available only on ADC instance: ADC4.\n
1400 * (5) On STM32G4, parameter available only on ADC instance: ADC5.\n
1401 * (6) On STM32G4, parameter available only on ADC instances: ADC1, ADC3, ADC5.\n
1402 * (7) On STM32G4, parameter available only on ADC instances: ADC1, ADC3, ADC4, ADC5.\n
1403 …* - On this STM32 series, all ADCx are not available on all devices. Refer to device dat…
1404 …* (8) On STM32G4, fast channel allows: 2.5 (sampling) + 12.5 (conversion) = 15 ADC clock c…
1450 * (1) On STM32G4, parameter available only on ADC instance: ADC1.\n
1451 * (2) On STM32G4, parameter available only on ADC instance: ADC2.\n
1452 * (3) On STM32G4, parameter available only on ADC instance: ADC3.\n
1453 * (4) On STM32G4, parameter available only on ADC instance: ADC4.\n
1454 * (5) On STM32G4, parameter available only on ADC instance: ADC5.\n
1455 * (6) On STM32G4, parameter available only on ADC instances: ADC1, ADC3, ADC5.\n
1456 * (7) On STM32G4, parameter available only on ADC instances: ADC1, ADC3, ADC4, ADC5.\n
1457 …* - On this STM32 series, all ADCx are not available on all devices. Refer to device dat…
1458 …* (8) On STM32G4, fast channel allows: 2.5 (sampling) + 12.5 (conversion) = 15 ADC clock c…
1516 * (1) On STM32G4, parameter available only on ADC instance: ADC1.\n
1517 * (2) On STM32G4, parameter available only on ADC instance: ADC2.\n
1518 * (3) On STM32G4, parameter available only on ADC instance: ADC3.\n
1519 * (4) On STM32G4, parameter available only on ADC instance: ADC4.\n
1520 * (5) On STM32G4, parameter available only on ADC instance: ADC5.\n
1521 * (6) On STM32G4, parameter available only on ADC instances: ADC1, ADC3, ADC5.\n
1522 * (7) On STM32G4, parameter available only on ADC instances: ADC1, ADC3, ADC4, ADC5.\n
1523 …* - On this STM32 series, all ADCx are not available on all devices. Refer to device dat…
1524 …* (8) On STM32G4, fast channel allows: 2.5 (sampling) + 12.5 (conversion) = 15 ADC clock c…
1577 * (1) On STM32G4, parameter available only on ADC instance: ADC1.\n
1578 * (2) On STM32G4, parameter available only on ADC instance: ADC2.\n
1579 * (3) On STM32G4, parameter available only on ADC instance: ADC3.\n
1580 * (4) On STM32G4, parameter available only on ADC instance: ADC4.\n
1581 * (5) On STM32G4, parameter available only on ADC instance: ADC5.\n
1582 * (6) On STM32G4, parameter available only on ADC instances: ADC1, ADC3, ADC5.\n
1583 * (7) On STM32G4, parameter available only on ADC instances: ADC1, ADC3, ADC4, ADC5.\n
1584 …* - On this STM32 series, all ADCx are not available on all devices. Refer to device dat…
1585 …* (8) On STM32G4, fast channel allows: 2.5 (sampling) + 12.5 (conversion) = 15 ADC clock c…
1613 * selected is available on the ADC instance selected.
1638 * (1) On STM32G4, parameter available only on ADC instance: ADC1.\n
1639 * (2) On STM32G4, parameter available only on ADC instance: ADC2.\n
1640 * (3) On STM32G4, parameter available only on ADC instance: ADC3.\n
1641 * (4) On STM32G4, parameter available only on ADC instance: ADC4.\n
1642 * (5) On STM32G4, parameter available only on ADC instance: ADC5.\n
1643 * (6) On STM32G4, parameter available only on ADC instances: ADC1, ADC3, ADC5.\n
1644 * (7) On STM32G4, parameter available only on ADC instances: ADC1, ADC3, ADC4, ADC5.\n
1645 …* - On this STM32 series, all ADCx are not available on all devices. Refer to device dat…
1646 …* @retval Value "0" if the internal channel selected is not available on the ADC instance selected.
1647 * Value "1" if the internal channel selected is available on the ADC instance selected.
1690 * @note On devices with only 1 ADC common instance, parameter of this macro
1773 * @note This voltage depends on user board environment: voltage level
1775 * On devices with small package, the pin Vref+ is not present
1777 * @note On this STM32 series, calibration data of internal voltage reference
1824 * @note On this STM32 series, calibration data of temperature sensor
1866 * If temperature sensor calibration values are available on
1867 * on this device (presence of macro __LL_ADC_CALC_TEMPERATURE()),
1879 …* On STM32G4, refer to device datasheet parameter "Avg_Slope…
1881 …* On STM32G4, refer to device datasheet parameter "V30" (cor…