Lines Matching refs:option
15 Enable this option to allow using random advertising interval
29 Enable this option to allow using specific duplicate scan filter
31 option in the Bluetooth Controller section in menuconfig, which is
67 Enable this option to use the default memory allocation strategy when
85 Enable this option to use FreeRTOS static allocation APIs for BLE Mesh,
88 If this option is disabled, the FreeRTOS static allocation APIs will not
159 Enable this option to allow BLE Mesh fast provisioning solution to be used.
162 When this option is enabled, and after an unprovisioned device is provisioned
168 Enable the device to be provisioned into a node. This option should be
175 Enable the device to be a Provisioner. The option should be enabled when
186 This option specifies how many unprovisioned devices can be added to device
187 queue for provisioning. Users can use this option to define the size of the
196 This option specifies how many devices can be provisioned by a Provisioner.
211 This option specifies how many devices can be provisioned at the same time
223 This option specifies how many devices can be provisioned at the same
234 This option specifies how many subnets per network a Provisioner can create.
242 This option specifies how many application keys the Provisioner can have.
249 When this option is enabled, Provisioner can call specific functions to enable
259 This option specifies how many heartbeat filter entries Provisioner supports.
269 # Virtual option enabled whenever Generic Provisioning layer is needed
274 Enable this option to support BLE Mesh Provisioning functionality. For
275 BLE Mesh, this option should be always enabled.
282 Enable this option to allow the device to be provisioned over the
283 advertising bearer. This option should be enabled if PB-ADV is
293 This option specifies the interval of sending two consecutive unprovisioned
294 device beacon, users can use this option to change the frequency of sending
296 unprovisioned device beacon will send every 5 seconds. When the option of
304 Enable this option to allow the device to be provisioned over GATT.
305 This option should be enabled if PB-GATT is going to be used during
308 # Virtual option enabled whenever any Proxy protocol is needed
313 Enable this option to support BLE Mesh Proxy protocol used by PB-GATT
322 This option enables support for Mesh GATT Proxy Service, i.e. the
324 This option should be enabled if a node is going to be a Proxy Server.
332 This option determines for how long the local node advertises using
335 So leaving the default value is the safest option.
338 set by this option. And after that, Network ID will be advertised.
346 This option specifies how many Proxy Filter entries the local node supports.
356 This option enables support for Mesh GATT Proxy Client. The Proxy Client
364 Enable BLE Mesh net buffer pool tracking. This option is used to introduce another
366 devices. Recommend to enable this option as default.
374 If the device is a BLE Mesh node, when this option is enabled, the configuration
390 The option allows nodes to delay a certain period of time to save proper
426 bool "A specific option for settings backward compatibility"
430 This option is created to solve the issue of failure in recovering
439 The new version mesh stack adds the option of "mesh/role" because
444 we recommend enabling this option, so that system could set the flag
457 flash (e.g. more than 20), this option is recommended to be enabled.
480 With this option enabled, Provisioner needs to use specific functions
490 This option specifies the maximum NVS namespaces supported by Provisioner.
499 This option specifies how many subnets a Mesh network can have at the same time.
507 This option specifies how many application keys the device can store per network.
515 This option specifies the maximum number of application keys to which each model
523 This option specifies the maximum number of addresses to which each model can
531 This option specifies how many Label UUIDs can be stored.
539 This option specifies the maximum capacity of the replay protection list.
557 Enable this option will refuse to relay such messages, which could help to
559 However, it should be noted that enabling this option may result in packet
561 Therefore, users need to decide whether to enable this option according to
570 unnecessary decryption operations and unnecessary relays. This option
607 option allows specifying a divider, i.e. how many intervals
625 When the above situation is encountered, this option can be used to decide whether
680 when setting this option to a higher value. There must be at
689 Support for acting as a Mesh Relay Node. Enabling this option will allow
692 option will let a node not support the Relay feature.
720 Enable this option to operate as a Low Power Node. If low power consumption
721 is required by a node, this option should be enabled. And once the node
735 When this option is enabled, the node will stop scanning for a period of
744 for Friend nodes. If this option is disabled LPN mode needs to be manually
747 enabling this option will trigger the node starts to send Friend Request at
858 Enable this option to be able to act as a Friend Node.
875 This option decides the size of each buffer which can be used by a Friend node
914 Select this to save the BLE Mesh related rodata code size. Enabling this option
1140 This option removes the 96 hour limit of the IV Update Procedure and
1142 If IV Update test mode is going to be used, this option should be enabled.
1148 This option is used to decide whether discarding the old SeqAuth when
1151 menu "BLE Mesh specific test option"
1157 This option adds extra self-tests which are run every time BLE Mesh
1164 This option is used to enable some internal functions for auto-pts test.
1171 This option is used to enable the log of auto-pts test.
1179 With this option enabled, an unprovisioned device can automatically
1188 With this option enabled, users can use white list to filter mesh