Lines Matching refs:app
96 … bool "Allow app adjust Dummy Cycle bits in SPI Flash for higher frequency (READ HELP FIRST)"
199 Partitions of type "app" cannot be specified here.
202 bool "GPIO triggers boot from test app partition"
206 Allows to run the test app from "TEST" partition.
217 To trigger a test app, this GPIO must be pulled low on reset.
227 Pin level for app test, can be triggered on low or high.
230 bool "Enter test app on GPIO low"
233 bool "Enter test app on GPIO high"
270 … If this option is set, the ESP-IDF app must explicitly reset, feed, or disable the rtc_wdt in
271 the app's own code.
290 bool "Enable app rollback support"
293 …After updating the app, the bootloader runs a new app with the "ESP_OTA_IMG_PENDING_VERIFY" state …
294 …This state prevents the re-run of this app. After the first boot of the new app in the user code, …
295 …function should be called to confirm the operability of the app or vice versa about its non-operab…
296 …If the app is working, then it is marked as valid. Otherwise, it is marked as not valid and rolls …
297 … the previous working app. A reboot is performed, and the app is booted before the software update.
298 …Note: If during the first boot a new app the power goes out or the WDT works, then roll back will …
302 bool "Enable app anti-rollback support"
309 int "eFuse secure version of app"
318 Bootloader: When bootloader selects an app to boot, an app is selected that has
320 The app is booted with a higher (or equal) secure version.
383 … Some applications need to boot very quickly from power on. By default, the entire app binary
386 Enabling this option will skip validation of the app when the SoC boots from power on.
387 Note that in this case it's not possible for the bootloader to detect if an app image is
388 … corrupted in the flash, therefore it's not possible to safely fall back to a different app
392 … Following other reset types, the bootloader will still validate the app image. This increases
394 …the bootloader will fall back to a valid app image. To increase the chances of successfully recove…
396 …OTLOADER_WDT_DISABLE_IN_USER_CODE - then manually disable the RTC Watchdog once the app is running.
407 Selecting this option prevents the bootloader from ever validating the app image before
408 booting it. Any flash corruption of the selected app partition will make the entire SoC
535 bool "Require signed app images"
540 …This option uses the same app signature scheme as hardware secure boot, but unlike hardware secure…
612 bool "Bootloader verifies app signatures"
616 …If this option is set, the bootloader will be compiled with code to verify that an app is signed b…
624 bool "Verify app signature on update"
647 …table or boot an app if the data has a verified digital signature. There are implications for refl…
717 … Once secure boot or signed app requirement is enabled, app images are required to be signed.
722 …If disabled, unsigned app/partition data will be built. They must be signed manually using espsecu…
731 Path to the key file used to sign app images.
750 app, to verify app images.
922 bool "Allow app partition length not 64KB aligned"
925 … If not set (default), app partition size must be a multiple of 64KB. App images are padded to 64KB
928 … space. This prevents an attacker from appending unverified data after the app image in the flash,
931 …Setting this option allows the app partition length to be unaligned, and disables padding of the a…
960 … If not set (default), during startup in the app all unused digest slots will be revoked.
1049 bool "Encrypt only the app image that is present in the partition of type app"
1054 by only encrypting the app image that is present in the partition,
1057 includes the size of the app image, checksum, hash and also the signature sector
1065 bool "Check Flash Encryption enabled on app startup"
1069 If set (default), in an app during startup code,
1072 The app requires this bit is on to continue work otherwise abort.
1074 If not set, the app does not care if the flash encryption eFuse bit is set or not.
1090 … If set, during startup the app will burn an eFuse bit to permanently disable the UART ROM
1107 … If set, during startup the app will burn an eFuse bit to permanently switch the UART ROM