Lines Matching +full:power +full:- +full:delay +full:- +full:ms
4 # SPDX-License-Identifier: Apache-2.0
113 bool "Mesh-specific workqueue"
116 mesh-specific workqueue. This will ensure that messages are always sent.
117 The application needs to ensure the mesh-specific workqueue size is large
130 CONFIG_BT_BUF_CMD_TX_COUNT, the host returns -ENOBUFS immediately
187 greater than zero, this can noticeably delay transmission of
189 in a friendship, this option can delay transmission of local
191 value. This in turn will result in increase of the power
192 consumption of the Low Power node.
209 thus reducing the scanning time on the Low Power node.
237 bool "PB-ADV support"
299 bool "PB-GATT Server support"
314 the PB-GATT is enabled.
317 bool "PB-GATT Client support"
509 Maximum number of simultaneous outgoing multi-segment and/or
521 Maximum number of simultaneous incoming multi-segment and/or
554 This value should typically be fine-tuned based on what
565 4-byte MIC and 52 bytes using an 8-byte MIC.
576 This value should typically be fine-tuned based on what
587 4-byte MIC and 52 bytes using an 8-byte MIC.
597 (CONFIG_BT_MESH_SAR_TX_SEG_INT_STEP + 1) * 10 ms.
626 (CONFIG_BT_MESH_SAR_TX_UNICAST_RETRANS_INT_STEP + 1) * 25 ms.
637 (CONFIG_BT_MESH_SAR_TX_UNICAST_RETRANS_INT_INC + 1) * 25 ms.
656 (CONFIG_BT_MESH_SAR_TX_MULTICAST_RETRANS_INT + 1) * 25 ms.
670 hex "Acknowledgment delay increment"
674 This value controls the delay increment of an interval used for
689 (CONFIG_BT_MESH_SAR_RX_SEG_INT_STEP + 1) * 10 ms
746 enabled this choice will provide a non-persistent implementation
842 The maximum number of messages the Access layer can manage to delay
867 When enabled, the periodic publications are randomly delayed by 20 to 50ms. Publications
869 20 to 500ms. This option reduces the probability of collisions when multiple nodes publish
925 is instantiated on a Low Power node, the pull request count will be
938 range 64 1048576 # 2^6 - 2^20
941 size will be some number that is a power of two, and is between block
951 size will be some number that is a power of two, and is between block
1008 Note: Without a delay between each sent chunk, the network might become too busy with the
1280 bool "Support for On-Demand Private Proxy Client model"
1282 On-Demand Private Proxy Client allows to configure and check the state
1283 of On-Demand Private Proxy Servers. The state determines if the peers will
1292 This timeout controls how long the On-Demand Private Proxy Client waits
1297 bool "Support for On-Demand Private Proxy Server model"
1301 The On-Demand Private Proxy Server is used to support configuration of
1496 that do not support TF-M.
1500 bool "Use TF-M PSA [EXPERIMENTAL]"
1504 Use TF-M as PSA Crypto API provider. This is only possible on platforms
1505 that support TF-M.
1574 ways that the node will be used and what kind of power source it
1587 bool "Support for Low Power features"
1589 Enable this option to be able to act as a Low Power Node.
1594 bool "Perform Friendship establishment using low power"
1597 Perform the Friendship establishment using low power, with
1629 int "RSSIFactor, used in the Friend Offer Delay calculation"
1634 in Friend Offer Delay calculations. 0 = 1, 1 = 1.5, 2 = 2, 3 = 2.5.
1637 int "ReceiveWindowFactor, used in the Friend Offer Delay calculation"
1642 Friend Offer Delay calculations. 0 = 1, 1 = 1.5, 2 = 2, 3 = 2.5.
1655 int "Receive delay requested by the local node"
1660 The ReceiveDelay is the time between the Low Power node
1661 sending a request and listening for a response. This delay
1664 the minimal value for the delay can not be less than 50ms due
1673 consecutive requests sent by the Low Power node. If no
1750 Friend node for a Low Power node.
1757 Number of Low Power Nodes the Friend can have a Friendship
1830 int "Delay (in seconds) before storing anything persistently"
1853 one used before power off.
1859 range -1 1000000
1869 may make sense. Setting this value to -1 will disable this timer.
1929 bool "Perform self-tests"
1931 This option adds extra self-tests which are run every time