Lines Matching +full:mic +full:- +full:feature +full:- +full:delay
4 # SPDX-License-Identifier: Apache-2.0
113 bool "Mesh-specific workqueue"
116 mesh-specific workqueue. This will ensure that messages are always sent.
117 The application needs to ensure the mesh-specific workqueue size is large
130 CONFIG_BT_BUF_CMD_TX_COUNT, the host returns -ENOBUFS immediately
173 Note that: The Subnet Bridge feature uses the relay advertising sets.
187 greater than zero, this can noticeably delay transmission of
188 local messages. When Friend feature is enabled and the node is
189 in a friendship, this option can delay transmission of local
237 bool "PB-ADV support"
299 bool "PB-GATT Server support"
314 the PB-GATT is enabled.
317 bool "PB-GATT Client support"
451 bool "Relay feature enabled by default"
454 Controls whether the Relay feature is enabled by default when the
494 Note that: The Subnet Bridge feature uses the relay advertising buffers. If both the Relay
495 feature and the Subnet Bridge feature is enabled, the added load should be taken into
509 Maximum number of simultaneous outgoing multi-segment and/or
513 feature of specification, set to zero will not allow send any
521 Maximum number of simultaneous incoming multi-segment and/or
525 feature of specification, set to zero will not allow receive any
554 This value should typically be fine-tuned based on what
562 which 4 or 8 bytes is used for the Transport Layer MIC). For
565 4-byte MIC and 52 bytes using an 8-byte MIC.
576 This value should typically be fine-tuned based on what
584 which 4 or 8 bytes is used for the Transport Layer MIC). For
587 4-byte MIC and 52 bytes using an 8-byte MIC.
670 hex "Acknowledgment delay increment"
674 This value controls the delay increment of an interval used for
746 enabled this choice will provide a non-persistent implementation
832 Controls whether the delayable message feature is enabled by default in
842 The maximum number of messages the Access layer can manage to delay
938 range 64 1048576 # 2^6 - 2^20
1008 Note: Without a delay between each sent chunk, the network might become too busy with the
1280 bool "Support for On-Demand Private Proxy Client model"
1282 On-Demand Private Proxy Client allows to configure and check the state
1283 of On-Demand Private Proxy Servers. The state determines if the peers will
1292 This timeout controls how long the On-Demand Private Proxy Client waits
1297 bool "Support for On-Demand Private Proxy Server model"
1301 The On-Demand Private Proxy Server is used to support configuration of
1392 Controls whether the GATT Proxy feature is enabled by default.
1410 the GATT Proxy feature is enabled.
1439 bool "Proxy solicitation feature"
1496 that do not support TF-M.
1497 This feature is experimental and only BabbleSim tests were run.
1500 bool "Use TF-M PSA [EXPERIMENTAL]"
1504 Use TF-M as PSA Crypto API provider. This is only possible on platforms
1505 that support TF-M.
1506 This feature is experimental.
1532 Controls whether the Secure network beacon feature is enabled by
1629 int "RSSIFactor, used in the Friend Offer Delay calculation"
1634 in Friend Offer Delay calculations. 0 = 1, 1 = 1.5, 2 = 2, 3 = 2.5.
1637 int "ReceiveWindowFactor, used in the Friend Offer Delay calculation"
1642 Friend Offer Delay calculations. 0 = 1, 1 = 1.5, 2 = 2, 3 = 2.5.
1655 int "Receive delay requested by the local node"
1661 sending a request and listening for a response. This delay
1664 the minimal value for the delay can not be less than 50ms due
1722 bool "Friend feature enabled by default"
1725 Controls whether the Friend feature is enabled by default when the
1830 int "Delay (in seconds) before storing anything persistently"
1859 range -1 1000000
1869 may make sense. Setting this value to -1 will disable this timer.
1929 bool "Perform self-tests"
1931 This option adds extra self-tests which are run every time