Lines Matching +full:initial +full:- +full:timeout +full:- +full:ms
4 # SPDX-License-Identifier: Apache-2.0
113 bool "Mesh-specific workqueue"
116 mesh-specific workqueue. This will ensure that messages are always sent.
117 The application needs to ensure the mesh-specific workqueue size is large
130 CONFIG_BT_BUF_CMD_TX_COUNT, the host returns -ENOBUFS immediately
237 bool "PB-ADV support"
288 int "Timeout value of retransmit provisioning PDUs"
292 Timeout value of retransmit provisioning PDUs.
299 bool "PB-GATT Server support"
314 the PB-GATT is enabled.
317 bool "PB-GATT Client support"
416 Controls the initial number of retransmissions of original messages,
425 Controls the initial interval between retransmissions of original
463 Controls the initial number of retransmissions of relayed messages, in
472 Controls the initial interval between retransmissions of relayed
509 Maximum number of simultaneous outgoing multi-segment and/or
521 Maximum number of simultaneous incoming multi-segment and/or
554 This value should typically be fine-tuned based on what
565 4-byte MIC and 52 bytes using an 8-byte MIC.
576 This value should typically be fine-tuned based on what
587 4-byte MIC and 52 bytes using an 8-byte MIC.
597 (CONFIG_BT_MESH_SAR_TX_SEG_INT_STEP + 1) * 10 ms.
614 acknowledgment was received during timeout, or if an
626 (CONFIG_BT_MESH_SAR_TX_UNICAST_RETRANS_INT_STEP + 1) * 25 ms.
637 (CONFIG_BT_MESH_SAR_TX_UNICAST_RETRANS_INT_INC + 1) * 25 ms.
656 (CONFIG_BT_MESH_SAR_TX_MULTICAST_RETRANS_INT + 1) * 25 ms.
689 (CONFIG_BT_MESH_SAR_RX_SEG_INT_STEP + 1) * 10 ms
692 hex "Discard timeout for reception of a segmented message"
746 enabled this choice will provide a non-persistent implementation
867 When enabled, the periodic publications are randomly delayed by 20 to 50ms. Publications
869 20 to 500ms. This option reduces the probability of collisions when multiple nodes publish
884 int "Config Client model timeout in milliseconds"
887 This timeout controls how long config client waits for a response
901 int "Health Client model timeout in milliseconds"
904 This timeout controls how long health client waits for a response
938 range 64 1048576 # 2^6 - 2^20
1010 Note: Timing restrictions, like the timeout base, should be considered or changed
1012 timeout settings and cause timeouts.
1233 int "Opcodes Aggregator Client model timeout in milliseconds"
1236 This timeout controls how long Opcodes Aggregator Client waits
1280 bool "Support for On-Demand Private Proxy Client model"
1282 On-Demand Private Proxy Client allows to configure and check the state
1283 of On-Demand Private Proxy Servers. The state determines if the peers will
1288 int "Solicitation PDU RPL Configuration Client model timeout in milliseconds"
1292 This timeout controls how long the On-Demand Private Proxy Client waits
1297 bool "Support for On-Demand Private Proxy Server model"
1301 The On-Demand Private Proxy Server is used to support configuration of
1326 int "Solicitation PDU RPL Configuration Client model timeout in milliseconds"
1330 This timeout controls how long Solicitation PDU RPL Configuration Client waits
1362 int "Bridge Configuration Client model timeout in milliseconds"
1365 This timeout controls how long the bridge configuration client waits for a
1396 int "Node Identity advertising timeout"
1496 that do not support TF-M.
1500 bool "Use TF-M PSA [EXPERIMENTAL]"
1504 Use TF-M as PSA Crypto API provider. This is only possible on platforms
1505 that support TF-M.
1621 int "Retry timeout for Friend requests"
1664 the minimal value for the delay can not be less than 50ms due
1684 The initial value of the PollTimeout timer when Friendship
1685 gets established for the first time. After this the timeout
1859 range -1 1000000
1869 may make sense. Setting this value to -1 will disable this timer.
1874 between this timeout and calling @ref bt_mesh_rpl_pending_store
1929 bool "Perform self-tests"
1931 This option adds extra self-tests which are run every time