Lines Matching full:of
43 # Basic controller functionalities required for implementation of
47 bool "Transmission of Constant Tone Extension"
51 Enable support for transmission of Constant Tone Extension in
55 bool "Reception of CTE with 1us sampling slots"
59 Enable reception of Constant Tone Extension. Process IQ sampling
81 Also known as Angle of Departure mode.
89 Also known as Angle of Arrival mode.
92 bool "Reception of Constant Tone Extension feature"
97 Enable support for reception of Constant Tone Extension in controller.
135 Enable transmission of Constant Tone Extension in
143 Enable reception and sampling of Constant Tone Extension in direction
149 bool "Sampling of CTE for PDUs with bad CRC"
153 Enable support for sampling of CTE for PDUs that have bad CRC.
158 int "Maximum length of antenna switch pattern"
163 Defines maximum length of antenna switch pattern that controller
170 bool "Initialization of GPIOs responsible for antenna switching"
174 Enable implicit initialization of GPIOs responsible for antenna
182 int "Maximum number of transmitted PDUs with Constant Tone Extension in connectionless mode"
187 Maximum supported number of PDUs, that have Constant Tone Extension, transmitted in single
192 int "Maximum number of received PDUs with Constant Tone Extension in connectionless mode"
197 Maximum supported number of PDUs, that have Constant Tone Extension, received in single
202 int "Antenna switch offset relative to end of CRC"
207 Offset of start of antenna switching after end of the CRC. It is a signed value in number
208 of 16M cycles. Decreasing the offset value beyond the trigger of the AoA/AoD procedure
217 Offset of sampling start from beginning of sampling slot. The value is a signed number
218 of 16M cycles relative. It is used when PHY is set to PHY 1M and sampling slot duration
219 is 1 us. Decreasing the offset beyond the trigger of the AoA/AoD procedure will have
228 Offset of sampling start from beginning of sampling slot. The value is a signed number
229 of 16M cycles relative. It is used when PHY is set to PHY 1M and sampling slot duration
230 is 1 us. Decreasing the offset beyond the trigger of the AoA/AoD procedure will have
240 Offset of sampling start from beginning of sampling slot. The value is a signed number
241 of 16M cycles relative. It is used when PHY is set to PHY 1M and sampling slot duration
242 is 2 us. Decreasing the offset beyond the trigger of the AoA/AoD procedure will have
251 Offset of sampling start from beginning of sampling slot. The value is a signed number
252 of 16M cycles relative. It is used when PHY is set to PHY 1M and sampling slot duration
253 is 2 us. Decreasing the offset beyond the trigger of the AoA/AoD procedure will have
278 bool "Conversion of IQ samples to 8 bits wide by 4 bits shift"
283 sections 7.7.65.21 and 7.7.65.22. This config enables conversion of 12 bit IQ samples to
288 bool "Conversion of IQ samples to 8 bits wide by 2 bits shift"
293 sections 7.7.65.21 and 7.7.65.22. This config enables conversion of 12 bit IQ samples to
299 bool "Conversion of IQ samples to 8 bits wide by use of 8 LSB"
304 sections 7.7.65.21 and 7.7.65.22. This config enables conversion of 12 bit IQ samples to
305 8 bits by use of 8 least significant bits. This conversion may be used only if you are
317 Direction Finging connectionless IQ reports provide a set of IQ samples collected during
318 sampling of CTE. Bluetooth 5.3 Core Specification defines IQ samples to be 8 bits signed
327 Direction Finging connection IQ reports provide a set of IQ samples collected during
328 sampling of CTE. Bluetooth 5.3 Core Specification defines IQ samples to be 8 bits signed