Lines Matching +full:current +full:- +full:limit
1 # Copyright 2019-2020, Peter Bigot Consulting, LLC
3 # SPDX-License-Identifier: Apache-2.0
6 Voltage/Current Regulators
14 regulator-name:
18 regulator-init-microvolt:
22 regulator-min-microvolt:
26 regulator-max-microvolt:
30 regulator-microvolt-offset:
34 regulator-init-microamp:
36 description: Current set during initialisation
38 regulator-min-microamp:
40 description: smallest current consumers may set
42 regulator-max-microamp:
44 description: largest current consumers may set
46 regulator-input-current-limit-microamp:
48 description: maximum input current regulator allows
50 regulator-always-on:
54 regulator-boot-on:
64 regulator-boot-off:
69 regulator-allow-bypass:
73 regulator-allow-set-load:
77 regulator-ramp-delay:
82 (regulator-ramp-delay = <0>) for disabling ramp delay.
84 regulator-enable-ramp-delay:
93 regulator-settling-time-us:
100 regulator-settling-time-up-us:
107 regulator-settling-time-down-us:
114 regulator-soft-start:
118 regulator-initial-mode:
125 regulator-allowed-modes:
129 regulator at run-time. Elements may be specified in any order. The set of
133 regulator-system-load:
139 regulator-pull-down:
143 regulator-over-current-protection:
145 description: Enable over current protection.
147 regulator-oc-protection-microamp:
150 Set over current protection limit. This is a limit where hardware performs
152 indicates that protection should be enabled but limit setting can be
155 regulator-oc-error-microamp:
158 Set over current error limit. This is a limit where part of the hardware
161 should be enabled but limit setting can be omitted.
163 regulator-oc-warn-microamp:
166 Set over current warning limit. This is a limit where hardware is assumed
167 still to be functional but approaching limit where it gets damaged.
170 limit setting can be omitted.
172 regulator-ov-protection-microvolt:
175 Set over voltage protection limit. This is a limit where hardware performs
177 indicates that protection should be enabled but limit setting can be
178 omitted. Limit is given as microvolt offset from voltage set to regulator.
180 regulator-ov-error-microvolt:
183 Set over voltage error limit. This is a limit where part of the hardware
186 should be enabled but limit setting can be omitted. Limit is given as
189 regulator-ov-warn-microvolt:
192 Set over voltage warning limit. This is a limit where hardware is assumed
193 still to be functional but approaching limit where it gets damaged.
196 limit setting can be omitted. Limit is given as microvolt offset from
199 regulator-uv-protection-microvolt:
202 Set over under voltage protection limit. This is a limit where hardware
204 value '1' indicates that protection should be enabled but limit setting
205 can be omitted. Limit is given as microvolt offset from voltage set to
208 regulator-uv-error-microvolt:
211 Set under voltage error limit. This is a limit where part of the hardware
214 should be enabled but limit setting can be omitted. Limit is given as
217 regulator-uv-warn-microvolt:
220 Set over under voltage warning limit. This is a limit where hardware is
221 assumed still to be functional but approaching limit where it gets
224 but limit setting can be omitted. Limit is given as microvolt offset from
227 regulator-temp-protection-kelvin:
230 Set over temperature protection limit. This is a limit where hardware
232 value '1' indicates that protection should be enabled but limit setting
235 regulator-temp-error-kelvin:
238 Set over temperature error limit. This is a limit where part of the
241 detection should be enabled but limit setting can be omitted.
243 regulator-temp-warn-kelvin:
246 Set over temperature warning limit. This is a limit where hardware is
247 assumed still to be functional but approaching limit where it gets
250 but limit setting can be omitted.
252 regulator-active-discharge:
255 - 0
256 - 1
263 regulator-max-step-microvolt:
266 Maximum difference between current and target voltages that can be changed
269 startup-delay-us:
273 off-on-delay-us: