Lines Matching full:this
44 Select this option if you have a NXP RW610-based
45 Wireless chip. This option will enable support
319 This option specifies the size of the stack used by the mon task.
325 This option specifies the size of the stack used by the wlcmgr task.
331 This option specifies the size of the stack used by the wifi powersave task.
338 This option specifies the size of the stack used by the wifi driver TX task.
344 This option specifies the size of the stack used by the wifi driver task.
350 This option specifies the size of the stack used by the wifi scan task.
361 This option specifies the priority of the mon task.
367 This option specifies the priority of the wlcmgr task.
373 This option specifies the priority of the wifi powersave task.
380 This option specifies the priority of the wifi driver TX task,
389 This option specifies the priority of the wifi driver task.
395 This option specifies the priority of the wifi scan task.
405 This option enables Station auto connection support.
414 This option specifies the SSID of the external Access Point
423 This option specifies the Passphrase of the external
434 This option enables Station auto reconnection support,
450 This option enables the use of extended scan support.
456 This option enables rssi threshold support in the Wi-Fi driver.
463 This is the maximum number of entries in the
475 This option sets the max scan channel gap time between two scan commands.
483 This option enables WMM UAPSD in the Wi-Fi driver.
491 This option enables Soft Roaming support in the Wi-Fi driver.
496 This option enables Cloud Keep Alive support in the Wi-Fi driver.
502 This option enables the use of 802.11k support.
508 This option enables the use of 802.11v support.
516 This option enables the use of 802.11r support.
522 This option enables the set of rts threshold support.
528 This option enables the use of Inactivity Timeout Ext support.
536 This option sets Wi-Fi max priority in the Wi-Fi driver.
568 This option enables uAP Wi-Fi Capability in the Wi-Fi driver.
580 This config enables the workaround of a
583 enabled this will enable the sticky TIM bit
584 workaround. A downside of this is that the STA
595 This option enables SDIO Multiport Rx Aggregation support in the Wi-Fi driver.
602 This option enables SDIO Multiport Rx Aggregation support in the Wi-Fi driver.
613 This option enables the use of 802.11ax support.
621 This option enables the use of 802.11ac support.
627 This option enables the use of 802.11 WMM support.
634 This option enables the use of single user support.
641 This option enables the use of multiple BSSID support.
647 This option enables the set of fragment threshold support.
653 This option enables the set of force RTS support.
659 This option enables TX AMPDU protection mode support.
665 This option enables the use of external coex PTA support.
673 This option enables WMM Turbo Mode support in the Wi-Fi driver.
680 This option enables the use of IPv6 support.
687 This option enables the use of 5GHz.
694 This option enables the Zero memory copy of data packets in Wi-Fi driver data path.
700 This option gets 802.11 log in the Wi-Fi driver.
705 This option is used to track Tx packet error ratio.
712 This option enable/disable channel state information collection.
718 This option is used to enable/disable/reset Wi-Fi.
724 This option is used to do channel switch according to spec.
731 This option is used to enable/disable UNII4 channels.
737 This option is used to enable wifi recovery support.
745 This option is to load some firmware features in run-time.
751 This option is to support sending null frame in period for CSI.
757 This option is used to set/get network monitor configuration.
763 This option is used to enable/disable Cau temperature.
769 This option is used to set and get Thermal Safeguard Protection configuration.
775 This option enable/disable config for IPS in the Wi-Fi driver.
781 This option enables rx abort config with static RSSI threshold
788 This option enables rx abort extension config with dynamic
795 This option enables cck desense mode in the Wi-Fi driver.
801 This option sets duty cycle in the Wi-Fi driver.
807 This option is used to specify/get 11ax density config in the Wi-Fi driver.
813 This option is used to set IM3 configuration for Wi-Fi,
820 This option is used to auto detect which two antennas are present and
826 This option is used to enable one antenna.
831 This option is used to enable one antenna diversity.
836 This option is used to enable three antenna diversity.
845 This option enables 11ax TWT in the Wi-Fi driver.
852 This option enables Wi-Fi packet forward on SoftAP.
858 This option is used to set dtim period in the Wi-Fi driver.
864 This option enables memory access cmd in the Wi-Fi driver.
870 This option enables register access cmd in the Wi-Fi driver.
876 This option prints the get subscribe event from firmware for user test.
882 This option enables TX/RX statistics in the Wi-Fi driver.
888 This option enables WLAN test mode commands.
894 This option enables EU Validation Support.
902 This option enables clock synchronization of TSF latches.
908 This option enables the use of Compress TX Power Table support.
914 This option enables the use of Compress RU TX Power Table support.
923 This option enables Wi-Fi EU Crypto support in the Wi-Fi driver.
929 This option enables HOST Sleep support for MCU.
935 This option enables Memory Efficient Filtering support in the Wi-Fi driver.
940 This option enables Wi-Fi FIPS support in the Wi-Fi driver.
946 This option enables Wi-Fi Opportunistic Wireless Encryption support
959 This option force to use custom calibration data.
967 This option enables the use of firmware auto recoonect support.
972 This option enables the use of Parallel firmware download support.
977 This option enables the use of Wi-Fi independent reset support.
988 This option is for development smoke tests in the Wi-Fi driver.
999 This option is to enable Wi-Fi Alliance Sigma Agent support in the Wi-Fi driver.
1041 If you enable this, error messages will be printed in case of error
1042 conditions. This will increase the size of the image. It is strongly
1050 If you enable this, error messages will be printed in case of error
1051 conditions. This will increase the size of the image. It is strongly
1059 If you enable this the debug options will be
1066 If you enable this the OS abstraction APIs debugs will be enabled.
1072 If you enable this the network driver abstraction APIs debugs will be enabled.
1078 If you enable this the WLAN Connection Manager APIs debugs will be enabled.
1086 This macro helps you to get additional debugging
1096 Enabling this will print out logs related
1097 to the uAP. This is enable to developer
1106 Enabling this will dump event codes of
1108 This helps the developer to checks the
1116 Enabling this will dump command and response
1124 Enabling this will dump command and response
1132 Enabling this will enable scan code logs
1133 This helps the developer to localize wlan
1141 Enabling this will enable packet TX/RX code logs
1142 This helps the developer to localize wlan
1149 Enabling this will dump information
1150 about input/output data packets. This information
1158 Enabling this will enable I/O debugging
1159 of wifi driver. This enables you to see
1167 Enabling this will enable I/O debugging
1168 of wifi driver. This enables you to see
1176 Enabling this will enable monitoring
1178 the wifi driver. This enables you to gauge
1185 Enabling this will help you to monitor what
1196 Enable this to monitor timer activity of the
1205 Enable this to monitor SDIO init deinit errors
1211 Enable this to monitor SDIO driver read write errors
1218 Enable this to monitor FW download debug logs
1224 Enable this to monitor debug logs from FW
1230 Enable this to monitor VDLL debug logs
1236 # This way we do not need to mark them as allowed for CI checks.