Lines Matching +full:window +full:- +full:mode
1 # Nordic Wi-Fi driver for nRF70 series SoCs
5 # SPDX-License-Identifier: Apache-2.0
21 Nordic Wi-Fi Driver
38 bool "low power mode in QSPI"
48 Select the operating mode of the nRF70 driver
51 bool "nRF70 system mode"
55 Select this option to enable system mode of the nRF70 driver
58 bool "nRF70 scan only mode"
60 Select this option to enable scan only mode of the nRF70 driver
63 bool "Radio test mode of the nRF70 driver"
66 bool "Offloaded raw TX mode of the nRF70 driver"
69 bool "nRF70 system mode with raw modes"
73 Select this option to enable system mode of the nRF70 driver with raw modes.
91 bool "nRF70 STA mode"
94 Select this option to enable STA mode of the nRF70 driver.
97 bool "Access point mode"
124 bool "Wi-Fi interface auto start on boot"
145 bool "Low power mode in nRF Wi-Fi chipsets"
169 module-dep = LOG
170 module-str = Log level for Wi-Fi nRF70 driver
171 module-help = Sets log level for Wi-Fi nRF70 driver
193 # Wi-Fi and SR Coexistence Hardware configuration.
195 bool "Wi-Fi and SR coexistence support"
199 depends on $(dt_node_has_prop,nrf70, srrf-switch-gpios)
203 …If this GPIO is asserted (1), the SR side RF switch is connected to the Wi-Fi side (shared antenna…
204 …If this GPIO is de-asserted (0), the SR side RF switch is connected to the SR side (separate anten…
223 bool "low power mode in QSPI"
232 The values are in dB scale in steps of 1 dB and range of 0-4 dB.
236 int "PCB loss for 5 GHz band (5150 MHz - 5350 MHz, Channel-32 - Channel-68)"
241 The values are in dB scale in steps of 1 dB and range of 0-4 dB.
245 int "PCB loss for 5 GHz band (5470 MHz - 5730 MHz, Channel-96 - Channel-144)"
250 The values are in dB scale in steps of 1 dB and range of 0-4 dB.
254 int "PCB loss for 5 GHz band (5730 MHz - 5895 MHz, Channel-149 - Channel-177)"
259 The values are in dB scale in steps of 1 dB and range of 0-4 dB.
268 int "Antenna gain for 5 GHz band (5150 MHz - 5350 MHz)"
273 int "Antenna gain for 5 GHz band (5470 MHz - 5730 MHz)"
278 int "Antenna gain for 5 GHz band (5730 MHz - 5895 MHz)"
313 int "HT/VHT Transmit power backoff (in dB) for lower edge of UNII-1 frequency band"
318 int "HE Transmit power backoff (in dB) for lower edge of UNII-1 frequency band"
323 int "HT/VHT Transmit power backoff (in dB) for upper edge of UNII-1 frequency band"
328 int "HE Transmit power backoff (in dB) for upper edge of UNII-1 frequency band"
333 int "HT/VHT Transmit power backoff (in dB) for lower edge of UNII-2A frequency band"
338 int "HE Transmit power backoff (in dB) for lower edge of UNII-2A frequency band"
343 int "HT/VHT Transmit power backoff (in dB) for upper edge of UNII-2A frequency band"
348 int "HE Transmit power backoff (in dB) for upper edge of UNII-2A frequency band"
353 int "HT/VHT Transmit power backoff (in dB) for lower edge of UNII-2C frequency band"
358 int "HE Transmit power backoff (in dB) for lower edge of UNII-2C frequency band"
363 int "HT/VHT Transmit power backoff (in dB) for upper edge of UNII-2C frequency band"
368 int "HE Transmit power backoff (in dB) for upper edge of UNII-2C frequency band"
373 int "HT/VHT Transmit power backoff (in dB) for lower edge of UNII-3 frequency band"
378 int "HE Transmit power backoff (in dB) for lower edge of UNII-3 frequency band"
383 int "HT/VHT Transmit power backoff (in dB) for upper edge of UNII-3 frequency band"
388 int "HE Transmit power backoff (in dB) for upper edge of UNII-3 frequency band"
393 int "HT/VHT Transmit power backoff (in dB) for lower edge of UNII-4 frequency band"
398 int "HE Transmit power backoff (in dB) for lower edge of UNII-4 frequency band"
403 int "HT/VHT Transmit power backoff (in dB) for upper edge of UNII-4 frequency band"
408 int "HE Transmit power backoff (in dB) for upper edge of UNII-4 frequency band"
447 default -15
490 dropped to conform to the SP window as per the specification that is, no
491 transmission outside SP window.
502 string "Wi-Fi Fixed MAC address in format XX:XX:XX:XX:XX:XX"
507 prompt "Wi-Fi MAC address type"
511 Select the type of MAC address to be used by the Wi-Fi driver
570 # Override the Wi-Fi subsystems WIFI_MGMT_SCAN_SSID_FILT_MAX parameter,
583 …bool "Wi-Fi beamforming. Enabling beamforming can provide a slight improvement in performance, whe…
590 menu "nRF Wi-Fi operation band(s)"
608 1 - 2.4GHz
609 2 - 5GHz
610 3 - All ( 2.4GHz and 5GHz )
614 int "MTU for Wi-Fi interface"
620 bool "Suppress networks with non-individual MAC addresses as BSSID in the scan results"
622 Wi-Fi access points use locally administered MAC addresses to manage
623 multiple virtual interfaces. For geo-location use cases, these networks
624 …from the virtual interfaces do not help in any way as they are co-located with the primary interfa…
648 # Relies on power-save mode, so, LPM is needed and AP mode is not supported
658 re-establish the network connection.
680 RPU attempts to enter power save mode in case of inactivity.
687 Minimum time the host should de-assert WAKEUP_NOW and let RPU enter
688 sleep mode, assuming there is no activity.
710 int "RPU recovery retry window in seconds"
713 Window in seconds during which the number of consecutive RPU recovery
715 exceeds NRF_WIFI_RPU_RECOVERY_MAX_RETRIES within this window, the system
728 This option controls disable/enable of the WMM (Wireless Multi-Media) feature.
737 bool "PS-Poll frame-based mechanism to retrieve buffered data from AP"
740 and retrieves the frames one-by-one. This conserves more power but adds latency
744 bool "QoS null frame-based mechanism to retrieve buffered data from AP"
761 bool "Wi-Fi keepalive feature for connection maintenance"
764 Enable the Wi-Fi keepalive feature to keep the connection alive by sending
788 power save mode might take some time and power.
804 This will override application-specified scan type.
808 # By default, the limit is 250 in scan-only mode and 150 in regular mode.
818 bool "Force disable priority window for scan in the case of coexistence with Short Range radio"
820 Enable this configuration to disable priority window for scan