Lines Matching +full:start +full:- +full:from +full:- +full:bottom
1 # Nordic Wi-Fi driver for nRF70 series SoCs
5 # SPDX-License-Identifier: Apache-2.0
21 Nordic Wi-Fi Driver
124 bool "Wi-Fi interface auto start on boot"
139 bool "Load nRF70 FW patches from external binary"
141 Select this option to load nRF70 FW patches from an external tooling.
145 bool "Low power mode in nRF Wi-Fi chipsets"
157 # Making calls to RPU from net_mgmt callbacks.
169 module-dep = LOG
170 module-str = Log level for Wi-Fi nRF70 driver
171 module-help = Sets log level for Wi-Fi nRF70 driver
193 # Wi-Fi and SR Coexistence Hardware configuration.
195 bool "Wi-Fi and SR coexistence support"
199 depends on $(dt_node_has_prop,nrf70, srrf-switch-gpios)
203 …If this GPIO is asserted (1), the SR side RF switch is connected to the Wi-Fi side (shared antenna…
204 …If this GPIO is de-asserted (0), the SR side RF switch is connected to the SR side (separate anten…
231 Specifies PCB loss from the antenna connector to the RF pin.
232 The values are in dB scale in steps of 1 dB and range of 0-4 dB.
236 int "PCB loss for 5 GHz band (5150 MHz - 5350 MHz, Channel-32 - Channel-68)"
240 Specifies PCB loss from the antenna connector to the RF pin.
241 The values are in dB scale in steps of 1 dB and range of 0-4 dB.
245 int "PCB loss for 5 GHz band (5470 MHz - 5730 MHz, Channel-96 - Channel-144)"
249 Specifies PCB loss from the antenna connector to the RF pin.
250 The values are in dB scale in steps of 1 dB and range of 0-4 dB.
254 int "PCB loss for 5 GHz band (5730 MHz - 5895 MHz, Channel-149 - Channel-177)"
258 Specifies PCB loss from the antenna connector to the RF pin.
259 The values are in dB scale in steps of 1 dB and range of 0-4 dB.
268 int "Antenna gain for 5 GHz band (5150 MHz - 5350 MHz)"
273 int "Antenna gain for 5 GHz band (5470 MHz - 5730 MHz)"
278 int "Antenna gain for 5 GHz band (5730 MHz - 5895 MHz)"
313 int "HT/VHT Transmit power backoff (in dB) for lower edge of UNII-1 frequency band"
318 int "HE Transmit power backoff (in dB) for lower edge of UNII-1 frequency band"
323 int "HT/VHT Transmit power backoff (in dB) for upper edge of UNII-1 frequency band"
328 int "HE Transmit power backoff (in dB) for upper edge of UNII-1 frequency band"
333 int "HT/VHT Transmit power backoff (in dB) for lower edge of UNII-2A frequency band"
338 int "HE Transmit power backoff (in dB) for lower edge of UNII-2A frequency band"
343 int "HT/VHT Transmit power backoff (in dB) for upper edge of UNII-2A frequency band"
348 int "HE Transmit power backoff (in dB) for upper edge of UNII-2A frequency band"
353 int "HT/VHT Transmit power backoff (in dB) for lower edge of UNII-2C frequency band"
358 int "HE Transmit power backoff (in dB) for lower edge of UNII-2C frequency band"
363 int "HT/VHT Transmit power backoff (in dB) for upper edge of UNII-2C frequency band"
368 int "HE Transmit power backoff (in dB) for upper edge of UNII-2C frequency band"
373 int "HT/VHT Transmit power backoff (in dB) for lower edge of UNII-3 frequency band"
378 int "HE Transmit power backoff (in dB) for lower edge of UNII-3 frequency band"
383 int "HT/VHT Transmit power backoff (in dB) for upper edge of UNII-3 frequency band"
388 int "HE Transmit power backoff (in dB) for upper edge of UNII-3 frequency band"
393 int "HT/VHT Transmit power backoff (in dB) for lower edge of UNII-4 frequency band"
398 int "HE Transmit power backoff (in dB) for lower edge of UNII-4 frequency band"
403 int "HT/VHT Transmit power backoff (in dB) for upper edge of UNII-4 frequency band"
408 int "HE Transmit power backoff (in dB) for upper edge of UNII-4 frequency band"
447 default -15
450 int "Priority of the workqueue for handling bottom half"
458 int "Stack size of the workqueue for handling bottom half"
496 of traffic available at the start of the SP.
502 string "Wi-Fi Fixed MAC address in format XX:XX:XX:XX:XX:XX"
504 This option overrides the MAC address read from OTP. It is strictly for testing purposes only.
507 prompt "Wi-Fi MAC address type"
511 Select the type of MAC address to be used by the Wi-Fi driver
514 bool "Use MAC address from OTP"
538 If data is active (for example, ping), the driver stores the RSSI value from
570 # Override the Wi-Fi subsystems WIFI_MGMT_SCAN_SSID_FILT_MAX parameter,
583 …bool "Wi-Fi beamforming. Enabling beamforming can provide a slight improvement in performance, whe…
590 menu "nRF Wi-Fi operation band(s)"
608 1 - 2.4GHz
609 2 - 5GHz
610 3 - All ( 2.4GHz and 5GHz )
614 int "MTU for Wi-Fi interface"
620 bool "Suppress networks with non-individual MAC addresses as BSSID in the scan results"
622 Wi-Fi access points use locally administered MAC addresses to manage
623 multiple virtual interfaces. For geo-location use cases, these networks
624 …from the virtual interfaces do not help in any way as they are co-located with the primary interfa…
626 So, to save resources, this option drops such networks from the scan results.
644 …are received from the AP. This is used to detect AP silently going down, for example, due to power…
648 # Relies on power-save mode, so, LPM is needed and AP mode is not supported
654 Enable the RPU recovery mechanism to recover from an RPU (nRF70) hang.
658 re-establish the network connection.
687 Minimum time the host should de-assert WAKEUP_NOW and let RPU enter
728 This option controls disable/enable of the WMM (Wireless Multi-Media) feature.
734 Select the mechanism to retrieve buffered data from AP.
737 bool "PS-Poll frame-based mechanism to retrieve buffered data from AP"
740 and retrieves the frames one-by-one. This conserves more power but adds latency
744 bool "QoS null frame-based mechanism to retrieve buffered data from AP"
757 from having to exchange commands and events for every management packet even if it is
761 bool "Wi-Fi keepalive feature for connection maintenance"
764 Enable the Wi-Fi keepalive feature to keep the connection alive by sending
782 Select the power save exit strategy to retrieve buffered data from AP.
785 bool "Exit power save every time to retrieve buffered data from AP"
787 Exit power save every time to retrieve buffered data from AP. Entering back to
793 Exit power save based on an intelligent algorithm to retrieve buffered data from the AP.
804 This will override application-specified scan type.
808 # By default, the limit is 250 in scan-only mode and 150 in regular mode.