Lines Matching +full:in +full:-
1 # Nordic Wi-Fi driver for nRF70 series SoCs
5 # SPDX-License-Identifier: Apache-2.0
21 Nordic Wi-Fi Driver
38 bool "low power mode in QSPI"
102 bool "P2P support in driver"
106 bool "RAW TX data path in the driver"
110 bool "RAW RX sniffer operation in the driver"
114 bool "Promiscuous RX sniffer operation in the driver"
120 bool "TX data path in the driver"
124 bool "Wi-Fi interface auto start on boot"
145 bool "Low power mode in nRF Wi-Fi chipsets"
153 …string "The ISO/IEC alpha2 country code for the country in which this device is currently operatin…
165 bool "Maintains the verbosity of information in logs"
169 module-dep = LOG
170 module-str = Log level for Wi-Fi nRF70 driver
171 module-help = Sets log level for Wi-Fi nRF70 driver
193 # Wi-Fi and SR Coexistence Hardware configuration.
195 bool "Wi-Fi and SR coexistence support"
199 depends on $(dt_node_has_prop,nrf70, srrf-switch-gpios)
203 …If this GPIO is asserted (1), the SR side RF switch is connected to the Wi-Fi side (shared antenna…
204 …If this GPIO is de-asserted (0), the SR side RF switch is connected to the SR side (separate anten…
220 bool "Utility shell in nRF70 driver"
223 bool "low power mode in QSPI"
232 The values are in dB scale in steps of 1 dB and range of 0-4 dB.
233 The loss is considered in the RX path only.
236 int "PCB loss for 5 GHz band (5150 MHz - 5350 MHz, Channel-32 - Channel-68)"
241 The values are in dB scale in steps of 1 dB and range of 0-4 dB.
242 The loss is considered in the RX path only.
245 int "PCB loss for 5 GHz band (5470 MHz - 5730 MHz, Channel-96 - Channel-144)"
250 The values are in dB scale in steps of 1 dB and range of 0-4 dB.
251 The loss is considered in the RX path only.
254 int "PCB loss for 5 GHz band (5730 MHz - 5895 MHz, Channel-149 - Channel-177)"
259 The values are in dB scale in steps of 1 dB and range of 0-4 dB.
260 The loss is considered in the RX path only.
268 int "Antenna gain for 5 GHz band (5150 MHz - 5350 MHz)"
273 int "Antenna gain for 5 GHz band (5470 MHz - 5730 MHz)"
278 int "Antenna gain for 5 GHz band (5730 MHz - 5895 MHz)"
283 int "DSSS Transmit power backoff (in dB) for lower edge of 2.4 GHz frequency band"
288 int "HT/VHT Transmit power backoff (in dB) for lower edge of 2.4 GHz frequency band"
293 int "HE Transmit power backoff (in dB) for lower edge of 2.4 GHz frequency band"
298 int "DSSS Transmit power backoff (in dB) for upper edge of 2.4 GHz frequency band"
303 int "HT/VHT Transmit power backoff (in dB) for upper edge of 2.4 GHz frequency band"
308 int "HE Transmit power backoff (in dB) for upper edge of 2.4 GHz frequency band"
313 int "HT/VHT Transmit power backoff (in dB) for lower edge of UNII-1 frequency band"
318 int "HE Transmit power backoff (in dB) for lower edge of UNII-1 frequency band"
323 int "HT/VHT Transmit power backoff (in dB) for upper edge of UNII-1 frequency band"
328 int "HE Transmit power backoff (in dB) for upper edge of UNII-1 frequency band"
333 int "HT/VHT Transmit power backoff (in dB) for lower edge of UNII-2A frequency band"
338 int "HE Transmit power backoff (in dB) for lower edge of UNII-2A frequency band"
343 int "HT/VHT Transmit power backoff (in dB) for upper edge of UNII-2A frequency band"
348 int "HE Transmit power backoff (in dB) for upper edge of UNII-2A frequency band"
353 int "HT/VHT Transmit power backoff (in dB) for lower edge of UNII-2C frequency band"
358 int "HE Transmit power backoff (in dB) for lower edge of UNII-2C frequency band"
363 int "HT/VHT Transmit power backoff (in dB) for upper edge of UNII-2C frequency band"
368 int "HE Transmit power backoff (in dB) for upper edge of UNII-2C frequency band"
373 int "HT/VHT Transmit power backoff (in dB) for lower edge of UNII-3 frequency band"
378 int "HE Transmit power backoff (in dB) for lower edge of UNII-3 frequency band"
383 int "HT/VHT Transmit power backoff (in dB) for upper edge of UNII-3 frequency band"
388 int "HE Transmit power backoff (in dB) for upper edge of UNII-3 frequency band"
393 int "HT/VHT Transmit power backoff (in dB) for lower edge of UNII-4 frequency band"
398 int "HE Transmit power backoff (in dB) for lower edge of UNII-4 frequency band"
403 int "HT/VHT Transmit power backoff (in dB) for upper edge of UNII-4 frequency band"
408 int "HE Transmit power backoff (in dB) for upper edge of UNII-4 frequency band"
447 default -15
482 int "RPU power save idle timeout in milliseconds"
488 In case frames accepted before the beginning of SP are not
494 in specification but not recommended. As the device is actively transmitting
502 string "Wi-Fi Fixed MAC address in format XX:XX:XX:XX:XX:XX"
507 prompt "Wi-Fi MAC address type"
511 Select the type of MAC address to be used by the Wi-Fi driver
516 This option uses the MAC address stored in the OTP memory of the nRF70.
533 int "RSSI stale timeout in milliseconds"
540 to wpa_supplicant. In this case, a higher value will be suitable
570 # Override the Wi-Fi subsystems WIFI_MGMT_SCAN_SSID_FILT_MAX parameter,
583 …l "Wi-Fi beamforming. Enabling beamforming can provide a slight improvement in performance, wherea…
587 int "Scan timeout in seconds"
590 menu "nRF Wi-Fi operation band(s)"
608 1 - 2.4GHz
609 2 - 5GHz
610 3 - All ( 2.4GHz and 5GHz )
614 int "MTU for Wi-Fi interface"
620 bool "Suppress networks with non-individual MAC addresses as BSSID in the scan results"
622 Wi-Fi access points use locally administered MAC addresses to manage
623 multiple virtual interfaces. For geo-location use cases, these networks
624 …from the virtual interfaces do not help in any way as they are co-located with the primary interfa…
629 bool "Disables DFS channels in scan operation"
631 This option disables inclusion of the DFS channels in the scan operation.
639 int "Access point dead detection timeout in seconds"
648 # Relies on power-save mode, so, LPM is needed and AP mode is not supported
658 re-establish the network connection.
662 int "RPU recovery propagation delay in milliseconds"
665 Propagation delay in milliseconds to wait after RPU is powered down
671 # Doing interface down and up even with delay puts a lot of events in the queue
675 int "RPU recovery power save active timeout in milliseconds"
678 Power save active timeout in milliseconds, after which the RPU recovery
680 RPU attempts to enter power save mode in case of inactivity.
683 int "Minimum idle time to enter sleep in milliseconds"
687 Minimum time the host should de-assert WAKEUP_NOW and let RPU enter
696 int "RPU recovery quiet period in milliseconds"
699 Quiet period in milliseconds after RPU recovery is triggered. During
710 int "RPU recovery retry window in seconds"
713 Window in seconds during which the number of consecutive RPU recovery
728 This option controls disable/enable of the WMM (Wireless Multi-Media) feature.
737 bool "PS-Poll frame-based mechanism to retrieve buffered data from AP"
739 When the AP notifies about the availability of buffered data, the STA stays in power save
740 and retrieves the frames one-by-one. This conserves more power but adds latency
744 bool "QoS null frame-based mechanism to retrieve buffered data from AP"
761 bool "Wi-Fi keepalive feature for connection maintenance"
764 Enable the Wi-Fi keepalive feature to keep the connection alive by sending
771 int "Keepalive period in seconds"
775 Keepalive period in seconds to send keepalive packets to the AP.
795 whether to stay in PS (for a lower amount of buffered data) or exit PS (for a higher
804 This will override application-specified scan type.
808 # By default, the limit is 250 in scan-only mode and 150 in regular mode.
815 Number of BSS entries in scan result.
818 bool "Force disable priority window for scan in the case of coexistence with Short Range radio"
821 in the case of coexistence with Short Range radio.