Lines Matching +full:long +full:- +full:frame +full:- +full:rx +full:- +full:support
15 is now the standard way to provide device-specific protection to data at rest. (:github:`76222`)
18 :ref:`ZMS <zms_api>` is a new key-value storage subsystem compatible with all non-volatile storage
19 types, including traditional NOR flash and advanced technologies like RRAM and MRAM that support
24 added, complete with shell support. It supports initial configuration through Devicetree and
25 runtime configuration through vendor specific APIs. Initially the :dtcompatible:`nordic,nrf-comp`,
26 :dtcompatible:`nordic,nrf-lpcomp` and :dtcompatible:`nxp,kinetis-acmp` are supported.
30 :ref:`stepper<stepper_api>` device driver subsystem, which also comes with shell support.
31 Initially implemented drivers include a simple :dtcompatible:`zephyr,gpio-steppers` and a complex
32 sensor-less stall-detection capable with integrated ramp-controller :dtcompatible:`adi,tmc5041`.
39 Zephyr's audio and video capabilities have been expanded with support for new image sensors, video
50 directory for :zephyr:code-sample-category:`code samples <samples>`.
52 * **Expanded Board Support**:
70 * :cve:`2024-8798`: Under embargo until 2024-11-22
71 * :cve:`2024-10395`: Under embargo until 2025-01-23
72 * :cve:`2024-11263` `Zephyr project bug tracker GHSA-jjf3-7x72-pqm9
73 <https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-jjf3-7x72-pqm9>`_
89 * Removed deprecated arch-level CMSIS header files
131 * Added support of device memory attributes on Cortex-M (arm_mpu_v8)
135 * Added initial support for :c:func:`arch_stack_walk` that supports unwinding via esf only
136 * Added sys_arch_reboot() support to ARM64
138 * Added support for demand paging.
140 * Added support for Linkable Loadable Extensions (LLEXT).
142 * RISC-V
144 * The stack traces upon fatal exception now prints the address of stack pointer (sp) or frame
147 …* When :kconfig:option:`CONFIG_EXTRA_EXCEPTION_INFO` is enabled, the exception stack frame (arch_e…
148 has an additional field ``csf`` that points to the callee-saved-registers upon an fatal error,
149 which can be accessed in :c:func:`k_sys_fatal_error_handler` by ``esf->csf``.
158 * Added initial support for :c:func:`arch_stack_walk` that supports unwinding via esf only
208 * Added support for non-bondable mode (SSP)
211 * Added support of security level 4 to SSP
213 * Added support for Multi-Command Packet (l2cap)
218 * Added support for SMP CT2 flag
223 …* Added Periodic Advertising Sync Transfer (PAST) support with support for both sending and receiv…
231 * Introduced a mesh-specific workqueue to increase reliability of the mesh messages
234 Boards & SoC Support
237 * Added support for these SoC series:
239 * Added ESP32-C2 and ESP8684 SoC support.
240 * Added STM32U0 series with GPIO, Serial, I2C, DAC, ADC, flash, PWM and counter driver support.
241 * Added STM32WB0 series with GPIO, Serial, I2C, SPI, ADC, DMA and flash driver support.
243 * Added NXP i.MX93's Cortex-M33 core
248 * NXP S32Z270: Added support for the new silicon cut version 2.0. Note that the previous
253 * Added ESP32 WROVER-E-N16R4 variant.
254 * STM32H5: Added support for OpenOCD through STMicroelectronics OpenOCD fork.
255 * MAX32: Enabled Segger RTT and SystemView support.
262 * added additional support to Wakeup from low power modes
272 * Nordic nRF54H: Added support for the FLPR (Fast Lightweight Processor) RISC-V CPU.
276 * Added support for these boards:
285 * :zephyr:board:`BeagleBone AI-64 <beaglebone_ai64>` (``beaglebone_ai64``)
288 * :zephyr:board:`Espressif ESP32-C3-DevKitC <esp32c3_devkitc>` (``esp32c3_devkitc``)
289 * :zephyr:board:`Espressif ESP32-C3-DevKit-RUST <esp32c3_rust>` (``esp32c3_rust``)
290 * :zephyr:board:`Espressif ESP32-S3-EYE <esp32s3_eye>` (``esp32s3_eye``)
291 * :zephyr:board:`Espressif ESP8684-DevKitM <esp8684_devkitm>` (``esp8684_devkitm``)
298 * :zephyr:board:`NXP FRDM-MCXA156 <frdm_mcxa156>` (``frdm_mcxa156``)
299 * :zephyr:board:`NXP FRDM-MCXC242 <frdm_mcxc242>` (``frdm_mcxc242``)
300 * :zephyr:board:`NXP FRDM-MCXC444 <frdm_mcxc444>` (``frdm_mcxc444``)
301 * :zephyr:board:`NXP FRDM-MCXN236 <frdm_mcxn236>` (``frdm_mcxn236``)
302 * :zephyr:board:`NXP FRDM-MCXW71 <frdm_mcxw71>` (``frdm_mcxw71``)
304 * :zephyr:board:`NXP MIMXRT1180-EVK <mimxrt1180_evk>` (``mimxrt1180_evk``)
305 * :ref:`PHYTEC phyBOARD-Nash i.MX93 <phyboard_nash>` (``phyboard_nash``)
321 * :zephyr:board:`Renode Cortex-R8 Virtual <cortex_r8_virtual>` (``cortex_r8_virtual``)
322 * :zephyr:board:`Seeed XIAO ESP32-S3 Sense Variant <xiao_esp32s3>`: ``xiao_esp32s3``.
323 * :ref:`sensry.io Ganymed Break-Out-Board (BOB) <ganymed_bob>` (``ganymed_bob``)
324 * :zephyr:board:`SiLabs SiM3U1xx 32-bit MCU USB Development Kit <sim3u1xx_dk>` (``sim3u1xx_dk``)
328 * :zephyr:board:`ST Nucleo H755ZI-Q <nucleo_h755zi_q>` (``nucleo_h755zi_q``)
333 * :zephyr:board:`ST STM32U083C-DK <stm32u083c_dk>` (``stm32u083c_dk``)
335 * :zephyr:board:`vcc-gnd YD-STM32H750VB <yd_stm32h750vb>` (``yd_stm32h750vb``)
345 * Support for Google Kukui EC board (``google_kukui``) has been dropped.
357 * ``mps3/an547/ns`` to ``mps3/corstone300/an547/ns`` for non-secure.
361 …, flexio pwm, flexio spi, watchdog, flash, rtc, i2c, lpspi, edma, gpio, acmp, adc and lptmr support
363 * Enabled support for MCUmgr on NXP boards
369 * Added support for the NXP ``imx8qm`` and ``imx8qxp`` DSP core to enable the openAMP sample
374 * Added support for the following shields:
376 * :ref:`ADI EVAL-ADXL362-ARDZ <eval_adxl362_ardz>`
377 * :ref:`ADI EVAL-ADXL372-ARDZ <eval_adxl372_ardz>`
382 * :ref:`ST X-NUCLEO-WB05KN1: BLE expansion board <x-nucleo-wb05kn1>`
388 * Added support for .elf files to the west flash command for jlink, pyocd and linkserver runners.
393 * ``--dts``
394 * ``--dtc-flags``
395 * ``--bindings-dirs``
396 * ``--dts-out``
397 * ``--edt-pickle-out``
398 * ``--vendor-prefixes``
399 * ``--edtlib-Werror``
404 * Added support for selecting MCUboot operating mode in sysbuild using ``SB_CONFIG_MCUBOOT_MODE``.
406 * Added support for RAM-load MCUboot operating mode in build system, including sysbuild support.
416 * Added a new :zephyr:code-sample-category:`interactive code sample catalog <samples>` for quickly
421 * Added :rst:dir:`zephyr:code-sample-category` directive to describe and group code samples in the
429 * Added two new build commands, ``make html-live`` and ``make html-live-fast``, that automatically
439 * Fixed calibration scheme in ESP32-S3.
440 * STM32H7: Added support for higher sampling frequencies thanks to boost mode implementation.
441 * Added initial support for Renesas RA8 ADC driver (:dtcompatible:`renesas,ra-adc`)
442 * Added driver for Analog Devices MAX32 SoC series (:dtcompatible:`adi,max32-adc`).
443 * Added support for NXP S32 SAR_ADC (:dtcompatible:`nxp,s32-adc-sar`)
444 * Added support for Ambiq Apollo3 series (:dtcompatible:`ambiq,adc`).
448 * Added initial support for Renesas RA CANFD (:dtcompatible:`renesas,ra-canfd-global`,
449 :dtcompatible:`renesas,ra-canfd`)
450 * Added Flexcan support for S32Z27x (:dtcompatible:`nxp,flexcan`, :dtcompatible:`nxp,flexcan-fd`)
451 * Improved NXP S32 CANXL error reporting (:dtcompatible:`nxp,s32-canxl`)
459 * STM32H7: PLL FRACN can now be configured (see :dtcompatible:`st,stm32h7-pll-clock`)
460 * Added initial support for Renesas RA clock control driver (:dtcompatible:`renesas,ra-cgc-pclk`,
461 :dtcompatible:`renesas,ra-cgc-pclk-block`, :dtcompatible:`renesas,ra-cgc-pll`,
462 :dtcompatible:`renesas,ra-cgc-external-clock`, :dtcompatible:`renesas,ra-cgc-subclk`,
463 :dtcompatible:`renesas,ra-cgc-pll-out`)
464 …* Silabs: Added support for Series 2+ Clock Management Unit (see :dtcompatible:`silabs,series-cloc…
465 * Added initial support for Nordic nRF54H Series clock controllers.
475 * Added support for Nordic nRF COMP (:dtcompatible:`nordic,nrf-comp`)
476 * Added support for Nordic nRF LPCOMP (:dtcompatible:`nordic,nrf-lpcomp`)
477 * Added support for NXP Kinetis ACMP (:dtcompatible:`nxp,kinetis-acmp`)
481 * Added initial support for Renesas RA8 AGT counter driver (:dtcompatible:`renesas,ra-agt`)
482 * Added driver for Analog Devices MAX32 SoC series (:dtcompatible:`adi,max32-counter`).
483 * Updated the NXP counter_mcux_lptmr driver to support multiple instances of the lptmr
486 …* Added support for late and short relative alarms area to NXP nxp_sys_timer (:dtcompatible:`nxp,s…
490 * Added support for STM32L4 AES.
494 …* DAC API now supports specifying channel path as internal. Support has been added in STM32 driver…
517 * Added driver for Analog Devices MAX32 SoC series (:dtcompatible:`adi,max32-dma`).
519 …* Added support for eDMAv5 and cyclic mode (:github:`80584`) to the NXP EMDA driver (:dtcompatible…
523 * Added support for using the EEPROM simulator with embedded C standard libraries
524 (:dtcompatible:`zephyr,sim-eeprom`).
528 * Added initial support for Renesas RA8 Entropy driver (:dtcompatible:`renesas,ra-rsip-e51a-trng`)
529 * Added driver for Analog Devices MAX32 SoC series (:dtcompatible:`adi,max32-trng`).
541 * Fixed bug that resulted in double RX buffer read when generic spi protocol is used.
546 * Added support for the ``zephyr,random-mac-address`` property.
558 * Added support for multiple instances of the liteX ethernet driver.
559 * Added support for VLAN to the liteX ethernet driver.
560 * Added phy support.
565 * NXP ENET_QOS: Fixed check for ``zephyr,random-mac-address`` property.
574 * Driver can now be configured to use a preemptive RX thread priority, which could be useful
576 * Added support for DT-defined mdio.
586 … * Fixed generic phy_mii driver not using the value of the ``no-reset`` property from Devicetree.
590 * Fixed reset times during init that were unnecessarily long.
592 * Fixed issue relating to strap-in override bits.
598 device tee when SFDP at run-time has been enabled (:github:`80383`)
599 * Updated all Espressif's SoC driver initialization to allow new chipsets and octal flash support.
610 * Extended STM32 OSPI drivers to support QUAL, DUAL and SPI modes. Additionally, added support
612 * Added possibility to run STM32H7 flash driver from Cortex-M4 core.
614 …* Added initial support for Renesas RA8 Flash controller driver (:dtcompatible:`renesas,ra-flash-h…
615 * Added driver for Analog Devices MAX32 SoC series (:dtcompatible:`adi,max32-flash-controller`).
616 * Added support for W25Q512JV and W25Q512NW-IQ/IN to NXP's MCUX Flexspi driver
617 * Renamed the binding :dtcompatible:`nxp,iap-msf1` to :dtcompatible:`nxp,msf1` for accuracy
621 …* tle9104: Add support for the parallel output mode via setting the properties ``parallel-out12`` …
622 ``parallel-out34``.
624 * Converted the NXP wake-up drivers to native Zephyr code
629 * Added support for TI DRV2605 haptic driver IC (:dtcompatible:`ti,drv2605`)
630 …* Added a sample for the DRV2605 haptic driver to trigger ROM events (:zephyr:code-sample:`drv2605…
634 * Added initial support for Renesas RA8 I2C driver (:dtcompatible:`renesas,ra-iic`)
638 * Added ESP32-S3 and ESP32-C3 driver support.
642 * Added support for SETAASA optimization during initialization. Added a
643 ``supports-setaasa`` property to ``i3c-devices.yaml``.
644 * Added sending DEFTGTS if any devices that support functioning as a secondary
652 * Added shell commands for setting the I3C speed, sending HDR-DDR, raising IBIs,
662 * New feature: :dtcompatible:`zephyr,input-double-tap`.
666 * Added power management support to all keyboard matrix drivers, added a
667 ``no-disconnect`` property to :dtcompatible:`gpio-keys` so it can be used
668 with power management on GPIO drivers that do not support pin
679 * Add support for multitouch events
690 * lp5562: added ``enable-gpios`` property to describe the EN/VCC GPIO of the lp5562.
692 * lp5569: added ``charge-pump-mode`` property to configure the charge pump of the lp5569.
694 * lp5569: added ``enable-gpios`` property to describe the EN/PWM GPIO of the lp5569.
700 * Updated ws2812 GPIO driver to support dynamic bus timings
704 * Added driver support for ESP32 and ESP32-S3 SoCs.
709 * Added support for mdio shell to stm32 mdio.
722 * Added support for the U-Blox LARA-R6 modem.
723 * Added support for setting the modem's UART baudrate during init.
725 * MIPI-DBI
727 * Added bitbang MIPI-DBI driver, supporting 8080 and 6800 mode
728 (:dtcompatible:`zephyr,mipi-dbi-bitbang`).
729 * Added support for STM32 FMC memory controller (:dtcompatible:`st,stm32-fmc-mipi-dbi`).
730 * Added support for 8080 mode to NXP LCDIC controller (:dtcompatible:`nxp,lcdic`).
733 * MIPI-CSI
735 * Improve NXP CSI and MIPI_CSI2Rx drivers to support varibale frame rates
739 * Added support for Microchip MEC5
740 * Added SCMI-based driver for NXP i.MX
741 * Added support for i.MX93 M33 core
742 * Added support for ESP32C2
749 * Added initial support for Renesas RA8 PWM driver (:dtcompatible:`renesas,ra8-pwm`)
750 * Added driver for Analog Devices MAX32 SoC series (:dtcompatible:`adi,max32-pwm`).
768 * Fixed a bug in the NXP SAI driver that caused a crash on a FIFO under- and overrun
770 * Added support for PM operations in NXP's SAI driver
774 * Added ESP32-S3 driver support.
775 * SPI SDHC driver now handles SPI devices with runtime PM support correctly
783 support all JEDEC JC 42.4 compatible temperature sensors. It now uses the
784 :dtcompatible:`jedec,jc-42.4-temp` compatible string instead to the ``microchip,mcp9808``
786 * Added support for VDD based ADC reference to the NTC thermistor driver.
794 * Add RTIO streaming support to ADXL345, ADXL362, and ADXL372 accelerometer drivers.
799 * Added support for power domains to BMM150 and BME680 drivers.
818 * Added I2C bus support to ICM42670.
822 * Added support for INA236 to the existing INA230 driver.
823 * Added support for TMAG3001 to the existing TMAG5273 driver.
832 * Added Würth Elektronik HIDS-2525020210002
833 :dtcompatible:`we,wsen-hids-2525020210002` humidity sensor driver.
841 * NS16550: Added support for Synopsys Designware 8250 UART.
842 * Renesas: Added support for SCI UART.
843 * Sensry: Added UART support for Ganymed SY1XX.
847 * Added initial support for Renesas RA8 SPI driver (:dtcompatible:`renesas,ra8-spi-b`)
848 * Added RTIO support to the Analog Devices MAX32 driver.
849 * Silabs: Added support for EUSART (:dtcompatible:`silabs,gecko-spi-eusart`)
857 * Added support for ADI TMC5041 (:dtcompatible:`adi,tmc5041`)
858 * Added support for gpio-stepper-controller (:dtcompatible:`zephyr,gpio-steppers`)
859 * Added stepper api test-suite
860 * Added stepper shell test-suite
864 * Silabs: Added support for Sleeptimer (:dtcompatible:`silabs,gecko-stimer`)
868 * Added support for USB HS on STM32U59x/STM32U5Ax SoC variants.
876 * Introduced API to control frame rate
878 …* Introduced API for :ref:`multi-heap<memory_management_shared_multi_heap>` video buffer allocatio…
880 …* Introduced bindings for common video link properties in ``video-interfaces.yaml``. Migration to …
884 (:zephyr:code-sample:`video-capture-to-lvgl`)
886 * Added support for GalaxyCore GC2145 image sensor (:dtcompatible:`galaxycore,gc2145`)
887 * Added support for ESP32-S3 LCD-CAM interface (:dtcompatible:`espressif,esp32-lcd-cam`)
888 * Added support for NXP MCUX SMARTDMA interface (:dtcompatible:`nxp,smartdma`)
889 * Added support for more OmniVision OV2640 controls (:dtcompatible:`ovti,ov2640`)
890 * Added support for more OmniVision OV5640 controls (:dtcompatible:`ovti,ov5640`)
894 * Added an NXP's smartdma based video driver (:dtcompatible:`nxp,video-smartdma`)
895 * Added frame interval APIs to support variable frame rates (video_sw_generator.c)
900 * Added 1-Wire master driver for Analog Devices MAX32 SoC series (:dtcompatible:`adi,max32-w1`)
904 * Added driver for Analog Devices MAX32 SoC series (:dtcompatible:`adi,max32-watchdog`).
907 * Wi-Fi
909 * Add Wi-Fi Easy Connect (DPP) support.
910 * Add support for Wi-Fi credentials library.
911 * Add enterprise support for station.
912 * Add Wi-Fi snippet support for networking samples.
913 * Add build testing for various Wi-Fi config combinations.
914 * Add regulatory domain support to Wi-Fi shell.
915 * Add WPS support to Wi-Fi shell.
916 * Add 802.11r connect command usage in Wi-Fi shell.
918 * Allow user to reset Wi-Fi statistics in Wi-Fi shell.
919 * Display RTS threshold in Wi-Fi shell.
923 * Fix setting of frequency band both in AP and STA mode in Wi-Fi shell.
924 * Fix correct channel scan range in Wi-Fi 6GHz.
925 * Fix scan results printing in Wi-Fi shell.
926 * Increase main and shell stack sizes for Wi-Fi shell sample.
927 * Increase the maximum count of connected STA to 8 in Wi-Fi shell.
928 * Relocate AP and STA Wi-Fi sample to samples/net/wifi directory.
929 * Run Wi-Fi tests together with network tests.
930 * Updated ESP32 Wi-Fi driver to reflect actual negotiated PHY mode.
931 * Add ESP32-C2 Wi-Fi support.
932 * Add ESP32 driver APSTA support.
933 * Add NXP RW612 driver support.
934 * Added nRF70 Wi-Fi driver.
941 * Implemented support for beacons without association bit.
942 * Implemented support for beacons payload.
943 * Fixed a bug where LL address endianness was swapped twice when deciphering a frame.
956 * Added support for runtime configuration of ACK random factor parameter.
957 * Added support for No Response CoAP option.
963 * Various fixes in the block transfer support in CoAP client.
971 * Added support for parsing multiple DNS servers received from DHCP server.
972 * Added support for DNS Server option in DHCPv4 server.
973 * Added support for Router option in DHCPv4 server.
974 * Added support for application callback which allows to assign custom addresses
985 * Added support for collecting DNS statistics.
986 * Added support for more error codes in :c:func:`zsock_gai_strerror`.
1001 * Added support for specifying response headers and response code by the application.
1002 * Added support for netusb in the HTTP server sample.
1003 * Added support for accessing HTTP request headers from the application callback.
1004 * Added support for handling IPv4 connections over IPv6 socket in HTTP server.
1005 * Added support for creating HTTP server instances without specifying local host.
1006 * Added overlays to support HTTP over IEEE 802.15.4 for HTTP client and server
1008 * Added support for static filesystem resources in HTTP server.
1012 * Fixed possible busy-looping in case of errors in the HTTP server sample.
1032 * Fixed endless IPv6 packet looping with both routing and VLAN support enabled.
1036 * Added onlink and forwarding check to IPv6-prepare
1046 * Added support for accepting SenML-CBOR floats decoded as integers.
1047 * Added support for X509 hostname verification if using certificates, when
1062 * Fixed c++ support in LwM2M public header.
1067 * Added support for network packet allocation statistics.
1068 * Added a new library implementing Prometheus monitoring support.
1069 * Added USB CDC NCM support for Echo Server sample.
1072 postfix in non-hexadecimal format.
1083 * Extended network tracing support and added documentation page
1092 * Updated MQTT tests to be self-contained, no longer requiring external broker.
1106 * Fixed native IP support being required to register IP addresses on an
1112 * Fixed compiler warnings when building with ``-Wtype-limits``.
1116 * Added support for :kconfig:option:`CONFIG_IEEE802154_SELECTIVE_TXCHANNEL`
1132 * Added support for enabling/disabling individual network shell commands with
1147 * Added TLS 1.3 support for TLS sockets.
1160 * Fixed possible busy-looping when polling TLS socket for POLLOUT event.
1169 * Added support for Websocket console in the Echo Server sample.
1173 * Wi-Fi:
1177 * Added AP configuration cmd support to the NXP Wifi drivers
1182 * Added support for USB CDC NCM in the zperf sample.
1193 * Made USB device stack high-bandwidth aware
1199 * Added support for string-array and array type properties to be enums.
1209 * Renamed ``power-domain`` base property to ``power-domains``,
1210 and introduced ``power-domain-names`` property. ``#power-domain-cells`` is now required as well.
1221 * Added west runner for probe-rs, a Rust-based embedded toolkit.
1227 * Added on-demand memory mapping support (:kconfig:option:`CONFIG_DEMAND_MAPPING`).
1235 * Added support for :ref:`mcumgr_smp_group_10`, which allows for listing information on
1239 * Added support for custom os mgmt bootloader info responses using notification hooks, this
1242 * Added support for img mgmt slot info command, which allows for listing information on
1244 * Added support for LoRaWAN MCUmgr transport, which can be enabled with
1270 * Added initial ESP32-C6 power management interface to allow light and deep-sleep features.
1276 * https://github.com/Mbed-TLS/mbedtls/releases/tag/mbedtls-3.6.1
1277 * https://github.com/Mbed-TLS/mbedtls/releases/tag/mbedtls-3.6.2
1280 was added to allow ``psa_get_random()`` to make use of non-cryptographically
1285 enable TLS 1.3 support from Mbed TLS. When this is enabled the following
1312 runtime, do ``kernel thread -h`` for more info.
1330 support libraries without enabling the File System subsystem. This option can be used
1334 * FAT FS: Added :kconfig:option:`CONFIG_FS_FATFS_LBA64` to enable support for the 64-bit LBA
1337 * FAT FS: Added :kconfig:option:`CONFIG_FS_FATFS_MULTI_PARTITION` that enables support for
1340 * FAT FS: Added :kconfig:option:`CONFIG_FS_FATFS_HAS_RTC` that enables RTC usage for time-stamping
1354 non-volatile storage technologies. It supports classical on-chip NOR flash as well as
1361 * Added support for a "user event" trace, with the purpose to allow driver or
1366 * Added support for the following Option Groups:
1371 * Added support for the following Options:
1378 * Support for :c:macro:`O_TRUNC` flag in :c:func:`open()`.
1379 * Support for :c:func:`rmdir` and :c:func:`remove`.
1383 * Support for :c:func:`asctime_r`, :c:func:`ctime_r`, and :c:func:`localtime_r`.
1407 * Introduced basic support for ARM's System Control and Management Interface, which includes:
1411 * Shared memory and mailbox-based transport
1419 * Added OS agnostic parts of the nRF70 Wi-Fi driver.
1442 overall driver support.
1466 * Added sysbuild support to the hello-world sample.
1470 * Added SHA512 support to MCUboot code and support for calculating SHA512 hash in imgtool.
1476 * Added compressed image flags and TLVs to MCUboot, Kconfig options and support for generating
1481 * Added non-bootable flag to imgtool.
1484 * Added bootutil support for maximum image size details for additional images.
1485 * Added support for automatically calculating max sectors.
1487 * Added support for keeping image encrypted in scratch area in bootutil.
1495 * Fixed bootutil issue with not zeroing AES and SHA-256 contexts with mbedTLS.
1496 * Fixed boot_serial ``format`` and ``incompatible-pointer-types`` warnings.
1502 * Fixed issue with properly retrieving image headers after interrupted swap-scratch in bootutil.
1503 * The MCUboot version in this release is version ``2.1.0+0-dev``.
1510 Trusted Firmware-M (TF-M)
1513 * TF-M was updated to version 2.1.1 (from 2.1.0).
1514 …The release notes can be found at: https://trustedfirmware-m.readthedocs.io/en/tf-mv2.1.1/releases…
1539 * You can now decide at run-time whether the decoder should enforce canonical encoding.
1541 * Allow --file-header to accept a path to a file with header contents
1550 * Added support for testing SDMMC devices to the fatfs API test
1551 * Extended net/vlan to add IPv6 prefix config to each vlan-iface
1558 * Added :zephyr:code-sample:`smf_calculator` sample demonstrating the usage of the State Machine fr…
1568 - :github:`71042` stream_flash: stream_flash_init() size parameter allows to ignore partition layout
1569 - :github:`67407` stream_flash: stream_flash_erase_page allows to accidentally erase stream
1570 - :github:`80875` stepper_api: incorrect c-prototype stepper.h and absence of NULL check stepper_sh…