Lines Matching +full:long +full:- +full:codes
21 taking a ``void *mem`` pointer instead of a ``void **mem`` double-pointer.
37 * The default C library used on most targets has changed from the built-in
47 increase by 8-16 bytes.
68 * Picolibc removes the ``-ffreestanding`` compiler option. This allows
71 the Zephyr required type -- ``int main(void)``.
74 'double', 'long long', 'integer', and 'minimal. 'double' offers a
76 hexadecimal formats, full integer support including long long, C99
77 integer size specifiers (j, z, t) and POSIX positional arguments. 'long
78 long' mode removes float support, 'integer' removes long long support
100 * ``psa-arch-tests``
102 * ``tf-m-tests``
103 * ``tflite-micro``
107 To enable them again use the ``west config manifest.project-filter -- +<module
108 name>`` command, or ``west config manifest.group-filter -- +optional`` to
114 * ``zephyr,memory-region-mpu`` was renamed ``zephyr,memory-attr`` and its type
118 .. code-block:: none
120 - "RAM" -> <( DT_MEM_ARM(ATTR_MPU_RAM) )>
121 - "RAM_NOCACHE" -> <( DT_MEM_ARM(ATTR_MPU_RAM_NOCACHE) )>
122 - "FLASH" -> <( DT_MEM_ARM(ATTR_MPU_FLASH) )>
123 - "PPB" -> <( DT_MEM_ARM(ATTR_MPU_PPB) )>
124 - "IO" -> <( DT_MEM_ARM(ATTR_MPU_IO) )>
125 - "EXTMEM" -> <( DT_MEM_ARM(ATTR_MPU_EXTMEM) )>
144 .. code-block:: devicetree
148 compatible = "zephyr,ram-disk";
149 disk-name = "RAM";
150 sector-size = <512>;
151 sector-count = <192>;
158 :dtcompatible:`zephyr,kscan-input` node.
160 * The ``zephyr,gpio-keys`` binding has been merged into
161 :dtcompatible:`gpio-keys` and the callback definition has been renamed from
183 * ``CONFIG_SSD1306_REVERSE_MODE`` is now set using the ``inversion-on``
189 ``-ENOSYS`` when these are not available, instead of ``-ENOTSUP``.
199 ``st,adc-clock-source`` allows choosing either synchronous or asynchronous clock source.
200 ``st,adc-prescaler`` allows setting the value of the prescaler for the chosen clock source.
206 .. code-block:: devicetree
213 * On NXP boards with LPC DMA, the DMA controller node used to have its ``dma-channels`` property
215 This did not match the zephyr dma-controller binding, so this property is now fixed and set
229 no longer fallback to the (Re-)Synchronization Jump Width (SJW) value set in the devicetree
238 * The CAN ISO-TP message configuration in :c:struct:`isotp_msg_id` is changed to use the following
241 * :c:macro:`ISOTP_MSG_EXT_ADDR` to enable ISO-TP extended addressing
242 * :c:macro:`ISOTP_MSG_FIXED_ADDR` to enable ISO-TP fixed addressing
243 * :c:macro:`ISOTP_MSG_IDE` to use extended (29-bit) CAN IDs
308 result, MDIO controller nodes now require ``#address-cells`` and
309 ``#size-cells`` properties. Similarly, Ethernet PHY devicetree nodes and
311 ``ethernet-phy`` instead of ``phy``. Devicetrees and overlays must be updated
314 .. code-block:: devicetree
317 compatible = "mdio-controller";
318 #address-cells = <1>;
319 #size-cells = <0>;
321 ethernet-phy@0 {
322 compatible = "ethernet-phy";
334 - Replace the integer ``CONFIG_ZBUS_RUNTIME_OBSERVERS_POOL_SIZE`` with the boolean
336 - Set the HEAP size with the :kconfig:option:`CONFIG_HEAP_MEM_POOL_SIZE`.
341 * MCUmgr SMP version 2 error codes entry has changed due to a collision with an
346 SMP version 2 error code defines for in-tree modules have been updated to
375 example :dtcompatible:`arm,gic-v2`, to the GIC node in the device tree.
379 ``nfct-pins-as-gpios`` property in devicetree. It can be set like this in the
382 .. code-block:: devicetree
385 nfct-pins-as-gpios;
390 ``gpio-as-nreset`` property in devicetree. It can be set like this in the
393 .. code-block:: devicetree
396 gpio-as-nreset;
413 initial CAN bitrate using the ``bus-speed``, ``sample-point``, ``bus-speed-data``, and
414 ``sample-point-data`` properties:
417 * ``prop-seg``
418 * ``phase-seg1``
419 * ``phase-seg1``
420 * ``sjw-data``
421 * ``prop-seg-data``
422 * ``phase-seg1-data``
423 * ``phase-seg1-data``