Lines Matching refs:command
20 local Controller supports. It is implied that if a command is listed as
21 supported, the feature underlying that command is also supported.
24 command is supported.
58 that either extend commands or don't have a vendor command. Most features are
59 indicated by the support its respective vendor command. The Supported Features
98 bootup and vendor specific Reset command includes the Fatal_Error event.
164 This command reads the values for the vendor version information for the local
244 When the Read_Version_Information command has completed, a Command Complete
251 This command reads the list of vendor commands supported for the local
262 This command shall return the Supported_Commands configuration parameter. It is
263 implied that if a command is listed as supported, the feature underlying that
264 command is also supported.
278 | | Bit mask for each vendor command |
281 | | supports the corresponding command |
283 | | command, unsupported or undefined |
287 When the Read_Supported_Commands command has completed, a Command Complete
294 This command reads the list of vendor features supported by the local Controller.
304 This command shall return the Supported_Features configuration parameter. The
322 When the Read_Supported_Features command has completed, a Command Complete
329 This command is used to control which vendor events are generated by the HCI
344 The vendor specific Reset command shall reset this event mask back to its
345 default value, but the standard HCI Reset command shall not reset this command
364 When the Set_Event_Mask command has completed, a Command Complete event shall
371 This command resets the vendor portion of the local Controller.
381 event related to the Reset command has been received.
384 HCI Reset command. While the standard HCI Reset command does not reset any
385 vendor specific settings, this command will reset everything back to defaults.
406 When the Reset command has completed, a Command Complete event shall be
413 This command writes the BD_ADDR (Bluetooth public device address) value
415 Read_BD_ADDR command.
424 To activate this address the standard HCI Reset command is required to be
426 Read_BD_ADDR. The vendor specific Reset command will reset the BD_ADDR to its
445 When the Write_BD_ADDR command has completed, a Command Complete event shall
452 This command is used to enable or disable the tracing functionality.
469 support when the Set_Trace_Enable command is supported.
497 When the Set_Trace_Enable command has completed, a Command Complete event shall
514 This command shall return the build information encoded as an UTF-8 string.
531 When the Read_Build_Information command has completed, a Command Complete
550 This command shall return the static addresses programmed by the vendor at
560 Read_Key_Hierarchy_Roots command shall not be returned from this command.
564 command. In case a public address is provided, then it is recommended to use
565 the Read_Key_Hierarchy_Roots command to return the identity root key (if only
601 When the Read_Static_Addresses command has completed, a Command Complete event
619 This command shall return the identity root key and encryption root key
627 command that have its dedicated identity root key assigned.
661 When the Read_Key_Hierarchy_Roots command has completed, a Command Complete
678 This command shall return the current chip temperature in degrees Celsius.
697 When the Read_Chip_Temperature command has completed, a Command Complete event
704 This command reads the list of host stack operation system defined vendor
717 This command shall return the list of host stack operation defined vendor
720 With this command it is possible to incorporate external defined HCI commands
725 command set. Ideally all external commands are multiplexed through that single
756 | 0xXXXX | Base opcode of command |
759 When the Read_Host_Stack_Commands command has completed, a Command Complete
801 When the Set_Scan_Request_Reports command has completed, a Command Complete
808 This command dynamically modifies BLE Tx power level given a handle and a
840 asynchronous service of the command as well. In addition, the command returns
852 | 0x03-0xFF | Reserved (HCI command error) |
923 When the Write_Tx_Power_Level command has completed, a Command Complete
930 This command reads the BLE Tx power level. In contrast to the standardized HCI
931 command, i.e. Read_Transmit_Power_Level, which returns the transmitted power
932 level only for a specified connection handle, this command operates for both
956 The command returns with an operational Status, and the replicated Handle_Type
967 | 0x03-0xFF | Reserved (HCI command error) |
1016 When the Read_Tx_Power_Level command has completed, a Command Complete
1022 This command read the supported USB transport modes.
1047 When the Read_USB_Transport_Mode command has completed, a Command Complete
1053 This command set the host transport mode and reset the controller states like
1054 an HCI Reset command.
1063 When the Set_USB_Transport_Mode command has completed, a Command Complete
1213 The event is reported by default unless masked away by Set_Event_Mask command.
1260 The event is only reported when unmasked by Set_Event_Mask command.
1325 The event is only reported when unmasked by Set_Event_Mask command.