Lines Matching +full:bit +full:- +full:per +full:- +full:seconds
13 - STM32 microcontroller in LQFP100 package
14 - USB OTG or full-speed device
15 - 1 user LED
16 - User, boot, and reset push-buttons
17 - 32.768 kHz and 25MHz HSE crystal oscillators
18 - External NOR Flash memories: 64-Mbit Quad-SPI and 64-Mbit SPI
19 - Board connectors:
21 - Camera (8 bit) connector
22 - ST7735 TFT-LCD 160 x 80 pixels (RGB565 3-SPI)
23 - microSD |trade| card
24 - USB Type-C Connector
25 - SWD header for external debugger
26 - 2x 40-pin GPIO connector
36 - STM32H7B0VBT6 in LQFP100 package
37 - ARM 32-bit Cortex-M7 CPU with FPU
38 - Chrom-ART Accelerator
39 - Hardware JPEG Codec
40 - 280 MHz max CPU frequency
41 - VDD from 1.62 V to 3.6 V
42 - 128 KB Flash
43 - 1.4 MB SRAM
44 - High-resolution timer (2.1 ns)
45 - 32-bit timers(2)
46 - 16-bit timers(10)
47 - SPI(5)
48 - I2C(4)
49 - I2S (4)
50 - USART(5)
51 - UART(5)
52 - USB OTG Full Speed and High Speed(1)
53 - CAN FD(2)
54 - SAI(4)
55 - SPDIF_Rx(4)
56 - HDMI_CEC(1)
57 - Dual Mode Quad SPI(1)
58 - Camera Interface
59 - GPIO (up to 80) with external interrupt capability
60 - 16-bit ADC(2) with 16 channels
61 - 12-bit DAC with 2 channels(2)
62 - True Random Number Generator (RNG)
63 - 16-channel DMA
64 - LCD-TFT Controller with XGA resolution
68 - `STM32H7B0VB on www.st.com`_
69 - `STM32H7B0VB reference manual`_
70 - `STM32H7B0VB datasheet`_
77 +-----------+------------+-------------------------------------+
80 | NVIC | on-chip | nested vector interrupt controller |
81 +-----------+------------+-------------------------------------+
82 | WDT | on-chip | watchdog |
83 +-----------+------------+-------------------------------------+
84 | PINMUX | on-chip | pinmux |
85 +-----------+------------+-------------------------------------+
86 | FLASH | on-chip | flash memory |
87 +-----------+------------+-------------------------------------+
88 | GPIO | on-chip | gpio |
89 +-----------+------------+-------------------------------------+
90 | SPI | on-chip | spi |
91 +-----------+------------+-------------------------------------+
92 | QSPI NOR | on-chip | off-chip flash |
93 +-----------+------------+-------------------------------------+
94 | SDMMC | on-chip | disk access |
95 +-----------+------------+-------------------------------------+
96 | DISPLAY | on-chip | display |
97 +-----------+------------+-------------------------------------+
101 The default configuration per core can be found in the defconfig file:
108 input/output, pull-up, etc.
113 ----------------------------------
117 - USER_LED : PE3
118 - USER_PB : PC13
119 - SPI1 SCK/MISO/MOSI/NSS : PB3/PB4/PD7/PD6 (NOR Flash memory)
120 - SPI4 SCK/MOSI/NSS : PE12/PE14/PE11 (LCD)
121 - QuadSPI CLK/NCS/IO0/IO1/IO2/IO3 : PB2/PB6/PD11/PD12/PE2/PD13 (NOR Flash memory)
122 - SDMMC1 CLK/DCMD/CD/D0/D1/D2/D3 : PC12/PD2/PD4/PC8/PC9/PC10/PC11 (microSD card)
123 - USB DM/DP : PA11/PA12 (USB CDC ACM)
145 an external debugger, such as ST-Link.
154 3. Wait for 0.5 seconds, then release the BOOT0 key.
161 ----------------------------------------
163 Here is an example for the :zephyr:code-sample:`hello_world` application.
170 .. zephyr-app-commands::
171 :zephyr-app: samples/hello_world
174 :gen-args: -DCONFIG_BOOT_DELAY=5000
178 .. code-block:: console
180 $ minicom -D <tty_device> -b 115200
182 Then, press the RESET button, you should see the following message after few seconds:
184 .. code-block:: console
192 ---------
202 .. zephyr-app-commands::
203 :zephyr-app: samples/basic/blinky
206 :gen-args: -DCONFIG_BOOT_DELAY=5000
218 .. zephyr-app-commands::
219 :zephyr-app: samples/subsys/shell/shell_module
222 :gen-args: -DCONFIG_BOOT_DELAY=5000
228 https://www.st.com/en/microcontrollers-microprocessors/stm32h7b0vb.html
231 …st.com/resource/en/reference_manual/rm0455-stm32h7a37b3-and-stm32h7b0-value-line-advanced-armbased…