Lines Matching +full:hold +full:- +full:time +full:- +full:2 +full:x
6 The Nucleo L4R5ZI board features an ARM Cortex-M4 based STM32L4R5ZI MCU
11 - STM32 microcontroller in LQFP144 package
12 - Two types of extension resources:
14 - Arduino Uno V3 connectivity
15 - ST morpho extension pin headers for full access to all STM32 I/Os
17 - On-board ST-LINK/V2-1 debugger/programmer with SWD connector
18 - Flexible board power supply:
20 - USB VBUS or external source(3.3V, 5V, 7 - 12V)
21 - Power management access point
23 - Three User LEDs: LD1 (Green), LD2 (Blue), LD3 (Red)
24 - Two push-buttons: USER and RESET
33 - Ultra-low-power with FlexPowerControl (down to 130 nA Standby mode
35 - Core: ARM |reg| 32-bit Cortex |reg|-M4 CPU with FPU, adaptive
36 real-time accelerator (ART Accelerator) allowing 0-wait-state
39 - Clock Sources:
41 - 4 to 48 MHz crystal oscillator
42 - 32 kHz crystal oscillator for RTC (LSE)
43 - Internal 16 MHz factory-trimmed RC ( |plusminus| 1%)
44 - Internal low-power 32 kHz RC ( |plusminus| 5%)
45 - Internal multispeed 100 kHz to 48 MHz oscillator, auto-trimmed by
47 - Internal 48 MHz with clock recovery
48 - 3 PLLs for system clock, USB, audio, ADC
50 - RTC with HW calendar, alarms and calibration
51 - Up to 24 capacitive sensing channels: support touchkey, linear and
53 - Advanced graphics features
55 - Chrom-ART Accelerator™ (DMA2D) for enhanced graphic content creation
56 - Chrom-GRC™ (GFXMMU) allowing up to 20% of graphic resources optimization
57 - MIPI® DSI Host controller with two DSI lanes running at up to 500
59 - LCD-TFT controller
61 - 16x timers
63 - 2 x 16-bit advanced motor-control
64 - 2 x 32-bit and 5 x 16-bit general purpose
65 - 2x 16-bit basic
66 - 2x low-power 16-bit timers (available in Stop mode)
67 - 2x watchdogs
68 - SysTick timer
70 - Up to 136 fast I/Os, most 5 V-tolerant, up to 14 I/Os with
72 - Memories
74 - 2-Mbyte Flash, 2 banks read-while-write, proprietary code readout protection
75 - 640 Kbytes of SRAM including 64 Kbytes with hardware parity check
76 - External memory interface for static memories supporting SRAM,
78 - 2 x OctoSPI memory interface
80 - 4x digital filters for sigma delta modulator
81 - Rich analog peripherals (independent supply)
83 - 12-bit ADC 5 Msps, up to 16-bit with hardware oversampling, 200 μA/Msps
84 - 2x 12-bit DAC, low-power sample and hold
85 - 2x operational amplifiers with built-in PGA
86 - 2x ultra-low-power comparators
88 - 20x communication interfaces
90 - USB OTG 2.0 full-speed, LPM and BCD
91 - 2x SAIs (serial audio interface)
92 - 4x I2C FM+(1 Mbit/s), SMBus/PMBus
93 - 6x USARTs (ISO 7816, LIN, IrDA, modem)
94 - 3x SPIs (5x SPIs with the dual OctoSPI)
95 - CAN (2.0B Active) and SDMMC
97 - 14-channel DMA controller
98 - True random number generator
99 - CRC calculation unit, 96-bit unique ID
100 - 8- to 14-bit camera interface up to 32 MHz (black and white) or 10 MHz (color)
101 - Development support: serial wire debug (SWD), JTAG, Embedded Trace
106 - `STM32L4R5ZI on www.st.com`_
107 - `STM32L4R5 reference manual`_
115 +-----------+------------+-------------------------------------+
118 | NVIC | on-chip | nested vector interrupt controller |
119 +-----------+------------+-------------------------------------+
120 | UART | on-chip | serial port-polling; |
121 | | | serial port-interrupt |
122 +-----------+------------+-------------------------------------+
123 | PINMUX | on-chip | pinmux |
124 +-----------+------------+-------------------------------------+
125 | GPIO | on-chip | gpio |
126 +-----------+------------+-------------------------------------+
127 | I2C | on-chip | i2c |
128 +-----------+------------+-------------------------------------+
129 | PWM | on-chip | pwm |
130 +-----------+------------+-------------------------------------+
131 | SPI | on-chip | spi |
132 +-----------+------------+-------------------------------------+
133 | USB | on-chip | usb |
134 +-----------+------------+-------------------------------------+
135 | ADC | on-chip | adc |
136 +-----------+------------+-------------------------------------+
137 | RTC | on-chip | rtc |
138 +-----------+------------+-------------------------------------+
150 responsible for pin muxing, input/output, pull-up, etc.
153 ---------------
158 For more details please refer to `STM32 Nucleo-144 board User Manual`_.
161 ----------------------------------
163 .. rst-class:: rst-columns
165 - UART_1_TX : PA9
166 - UART_1_RX : PA10
167 - UART_2_TX : PA2
168 - UART_2_RX : PA3
169 - UART_3_TX : PB10
170 - UART_3_RX : PB11
171 - I2C_1_SCL : PB6
172 - I2C_1_SDA : PB7
173 - SPI_1_NSS : PD14
174 - SPI_1_SCK : PA5
175 - SPI_1_MISO : PA6
176 - SPI_1_MOSI : PA7
177 - SPI_2_NSS : PB12
178 - SPI_2_SCK : PB13
179 - SPI_2_MISO : PB14
180 - SPI_2_MOSI : PB15
181 - SPI_3_NSS : PB12
182 - SPI_3_SCK : PC10
183 - SPI_3_MISO : PC11
184 - SPI_3_MOSI : PC12
185 - PWM_2_CH1 : PA0
186 - USER_PB : PC13
187 - LD1 : PC7
188 - LD2 : PB7
189 - LD3 : PB14
190 - USB DM : PA11
191 - USB DP : PA12
192 - ADC1 : PC0
195 ------------
204 -----------
210 -----------------
217 The NUCLEO-L4R5ZI board includes a ST-LINK/V2 embedded debug tool interface.
223 so its :ref:`installation <stm32cubeprog-flash-host-tools>` is required.
226 the ``--runner`` (or ``-r``) option:
228 .. code-block:: console
230 $ west flash --runner openocd
231 $ west flash --runner jlink
234 ----------------------------------------
239 Here is an example for the :zephyr:code-sample:`hello_world` application.
243 .. code-block:: console
245 $ minicom -D /dev/ttyACM0
249 .. zephyr-app-commands::
250 :zephyr-app: samples/hello_world
256 .. code-block:: console
261 https://www.st.com/en/evaluation-tools/nucleo-l4r5zi.html
263 .. _STM32 Nucleo-144 board User Manual:
272 .. _STM32 ST-LINK utility:
273 …/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/…
276 https://www.st.com/en/development-tools/stm32cubeprog.html