Lines Matching +full:pro +full:-

3 SparkFun Pro Micro RP2040
9 The SparkFun Pro Micro RP2040 is a small, low-cost, versatile board from
10 SparkFun. It is equipped with an RP2040 SoC, an on-board WS2812 addressable
12 to be flashed without any adapter, in a drag-and-drop manner.
16 - Dual core Arm Cortex-M0+ processor running up to 133MHz
17 - 264KB on-chip SRAM
18 - 16MB on-board QSPI flash with XIP capabilities
19 - 18 GPIO pins
20 - 4 Analog inputs
21 - 1 UART peripherals
22 - 1 SPI controllers
23 - 2 I2C controllers (one via Qwiic connector)
24 - 16 PWM channels
25 - USB 1.1 controller (host/device)
26 - 8 Programmable I/O (PIO) for custom peripherals
27 - On-board RGB LED
28 - 1 Watchdog timer peripheral
33      :alt: SparkFun Pro Micro RP2040
35      SparkFun Pro Micro RP2040 (Image courtesy of SparkFun)
43 .. list-table::
44    :header-rows: 1
46    * - Peripheral
47      - Kconfig option
48      - Devicetree compatible
49    * - NVIC
50      - N/A
51      - :dtcompatible:`arm,v6m-nvic`
52    * - UART
53      - :kconfig:option:`CONFIG_SERIAL`
54      - :dtcompatible:`raspberrypi,pico-uart`
55    * - GPIO
56      - :kconfig:option:`CONFIG_GPIO`
57      - :dtcompatible:`raspberrypi,pico-gpio`
58    * - ADC
59      - :kconfig:option:`CONFIG_ADC`
60      - :dtcompatible:`raspberrypi,pico-adc`
61    * - I2C
62      - :kconfig:option:`CONFIG_I2C`
63      - :dtcompatible:`snps,designware-i2c`
64    * - SPI
65      - :kconfig:option:`CONFIG_SPI`
66      - :dtcompatible:`raspberrypi,pico-spi`
67    * - USB Device
68      - :kconfig:option:`CONFIG_USB_DEVICE_STACK`
69      - :dtcompatible:`raspberrypi,pico-usbd`
70    * - HWINFO
71      - :kconfig:option:`CONFIG_HWINFO`
72      - N/A
73    * - Watchdog Timer (WDT)
74      - :kconfig:option:`CONFIG_WATCHDOG`
75      - :dtcompatible:`raspberrypi,pico-watchdog`
76    * - PWM
77      - :kconfig:option:`CONFIG_PWM`
78      - :dtcompatible:`raspberrypi,pico-pwm`
79    * - Flash
80      - :kconfig:option:`CONFIG_FLASH`
81      - :dtcompatible:`raspberrypi,pico-flash`
82    * - Clock controller
83      - :kconfig:option:`CONFIG_CLOCK_CONTROL`
84      - :dtcompatible:`raspberrypi,pico-clock-controller`
85    * - UART (PIO)
86      - :kconfig:option:`CONFIG_SERIAL`
87      - :dtcompatible:`raspberrypi,pico-uart-pio`
97 ----------------------------------
99 .. rst-class:: rst-columns
101 - UART0_TX : P0
102 - UART0_RX : P1
103 - I2C1_SDA : P2
104 - I2C1_SCL : P3
105 - SPI0_RX : P20
106 - SPI0_SCK : P18
107 - SPI0_TX : P19
116 ---------
118 The Pro Micro board does make the SWD pins available on pads on the
122 :file:`build/zephyr/zephyr.uf2` file. If the Pro Micro RP2040 is powered on with
125 flash the Pro Micro RP2040.
127 .. target-notes::
130   https://datasheets.raspberrypi.com/pico/getting-started-with-pico.pdf