Lines Matching +full:video +full:- +full:interfaces
6 SBC-3.5-PX30 (JUNO - D23) is a Single Board Computer based on embedded Rockchip PX30
7 Processor, featuring Quad-Core ARM Cortex-A35 processor. The processor
8 integrates a Mali-G31 GPU with High performance dedicated 2D processor,
10 Embedded VPU is able to support video decoding of the most common coding
11 standard (MPEG-4, H.265/HEVC, H.264, VP8, VC-1). The board is completed with up
12 to 4GB LPDDR4-3200 32-bit bus memory directly soldered on board and one eMMC
17 The audio functionalities are managed by the AudioCodec embedded in the RK-809
18 PMIC. SBC-3.5-PX30 board is completed by a series of connectors with various
19 interfaces (UART, SPI, I2C) managed by the microcontroller STM32F302VCT6.
24 SECO SBC-3.5-PX30 provides the following hardware components:
26 - STM32F302VCT6
27 - ARM |reg| 32-bit Cortex |reg| -M4 CPU with FPU
28 - 256 KB Flash
29 - 40 KB SRAM
30 - 72 MHz max CPU frequency
31 - 2 User LEDs
32 - 16 GPI
33 - 16 GPO
34 - 4 U(S)ART
35 - Modbus
36 - RS485
37 - TTL Serial Debug
38 - TTL Serial
39 - 8-channel General Purpose Timers
40 - USB 2.0 full speed interface
41 - CAN
42 - I2C (up to 2)
43 - SPI
47 - `STM32F302VC on www.st.com`_
48 - `STM32F302xC reference manual`_
56 +-----------+------------+-------------------------------------+
59 | NVIC | on-chip | nested vector interrupt controller |
60 +-----------+------------+-------------------------------------+
61 | UART | on-chip | serial port-polling; |
62 | | | serial port-interrupt |
63 +-----------+------------+-------------------------------------+
64 | PINMUX | on-chip | pinmux |
65 +-----------+------------+-------------------------------------+
66 | GPIO | on-chip | gpio |
67 +-----------+------------+-------------------------------------+
68 | I2C | on-chip | i2c |
69 +-----------+------------+-------------------------------------+
70 | SPI | on-chip | spi |
71 +-----------+------------+-------------------------------------+
72 | USB | on-chip | USB device |
73 +-----------+------------+-------------------------------------+
74 | CAN | on-chip | CAN |
75 +-----------+------------+-------------------------------------+
76 | IWDG | on-chip | Independent WatchDoG |
77 +-----------+------------+-------------------------------------+
78 | PWM | on-chip | pwm |
79 +-----------+------------+-------------------------------------+
86 SBC-3.5-PX30 has 6 GPIO controllers. These controllers are
87 responsible for pin muxing, input/output, pull-up, etc.
89 For more details please refer to `SECO SBC-3.5-PX30 board User Manual`_.
92 ----------------------------------
94 .. rst-class:: rst-columns
96 - UART_1_TX : PA9 (debug config for UART_1)
97 - UART_1_RX : PA10 (debug config for UART_1)
98 - UART_1_TX : PC4 (alternate config for UART_1)
99 - UART_1_RX : PC5 (alternate config for UART_1)
100 - UART_2_TX : PD5
101 - UART_2_RX : PD6
102 - UART_2_CLK : PD7
103 - UART_2_CTS : PD3
104 - UART_2_RTS/DE : PD4
105 - UART_3_TX : PC10
106 - UART_3_RX : PC11
107 - UART_3_CLK : PD10
108 - UART_3_CTS : PD11
109 - UART_3_RTS/DE : PD12
110 - UART_5_TX : PC12
111 - UART_5_RX : PD2
112 - I2C1_SCL : PB6
113 - I2C1_SDA : PB7
114 - I2C2_SCL : PA9 (alternate config for UART_1)
115 - I2C2_SDA : PA10 (alternate config for UART_1)
116 - SPI1_NSS : PA4
117 - SPI1_SCK : PB3
118 - SPI1_MISO : PB4
119 - SPI1_MOSI : PB5
120 - SPI2_NSS : PB12
121 - SPI2_SCK : PB13
122 - SPI2_MISO : PB14
123 - SPI2_MOSI : PB15
124 - CAN1_RX : PB8
125 - CAN1_TX : PB9
126 - USB_DM : PA11
127 - USB_DP : PA12
128 - LD1 : PD8
129 - LD2 : PD9
130 - PWM : PA8
135 SECO SBC-3.5-PX30 System Clock could be driven by internal or external
142 SECO SBC-3.5-PX30 has up to 4 U(S)ARTs. The Zephyr console output
147 UART3 provides RS-485 interface to connectors CN57 and CN48.
154 SECO SBC-3.5-PX30 has up to 2 I2Cs. Both are present in connector CN33.
159 SECO SBC-3.5-PX30 has a USB 2.0 full-speed device interface available through
164 SECO SBC-3.5-PX30 has an onboard CAN transceiver (TJA1051T), and it is
169 SECO SBC-3.5-PX30 has two SPI lines: SPI1 is an internal SPI line connected to the
182 Flashing an application to SECO SBC-3.5-PX30
183 --------------------------------------------
185 First, connect the SECO SBC-3.5-PX30 to your host computer using
186 CN56 connector to an ST-Link.
188 The pinout is (1-8):
190 - VDD
191 - UART1_TX
192 - UART1_RX
193 - BOOT_0
194 - SWDIO_JTMS
195 - SWCLK_JTCK
196 - EC_RST#
197 - GND
201 Here is an example for the :zephyr:code-sample:`hello_world` application.
203 .. zephyr-app-commands::
204 :zephyr-app: samples/hello_world
210 .. code-block:: console
212 $ minicom -D /dev/<tty device>
214 Replace <tty_device> with the port where the SBC-3.5-PX30 board can be
219 .. code-block:: console
224 .. _SECO SBC-3.5-PX30 website:
225 https://edge.seco.com/sbc-3-5-px30.html
227 .. _SECO SBC-3.5-PX30 board User Manual:
228 https://www.seco.com/Manuals/SBC-D23_Manual.pdf
234 …ww.st.com/resource/en/reference_manual/rm0365-stm32f302xbcde-and-stm32f302x68-advanced-armbased-32…