Lines Matching +full:ra +full:- +full:sdram +full:- +full:control
9 The EK-RA8D1 is an Evaluation Kit for Renesas RA8D1 MCU Group which are the industry’s first 32-bit
10 graphics-enabled MCUs based on the Arm Cortex-M85 (CM85) core, delivering breakthrough performance
11 of over 3000 Coremark points at 480 MHz and superior graphics capabilities that enable high-resolut…
14 The key features of the EK-RA8D1 board are categorized in three groups as follow:
18 - 480MHz Arm Cortex-M85 based RA8D1 MCU in 224 pins, BGA package
19 - Native pin acces througgh 2 x 50-pin, and 2 x 40-pin male headers
20 - MCU current measurement points for precision current consumption measurement
21 - Multiple clock sources - RA8D1 MCU oscillator and sub-clock oscillator crystals,
25 **System Control and Ecosystem Access**
27 - USB Full Speed Host and Device (micro-AB connector)
28 - Four 5V input sources
30 - USB (Debug, Full Speed, High Speed)
31 - External power supply (using surface mount clamp test points and power input vias)
33 - Three Debug modes
35 - Debug on-board (SWD)
36 - Debug in (ETM, SWD and JTAG)
37 - Debug out (SWD)
39 - User LEDs and buttons
41 - Three User LEDs (red, blue, green)
42 - Power LED (white) indicating availability of regulated power
43 - Debug LED (yellow) indicating the debug connection
44 - Two User buttons
45 - One Reset button
47 - Five most popular ecosystems expansions
49 - Two Seeed Grove system (I2C/I3C) connectors
50 - One SparkFun Qwiic connector
51 - Two Digilent Pmod (SPI, UART and I2C/I3C) connectors
52 - Arduino (Uno R3) connector
53 - MikroElektronika mikroBUS connector
55 - MCU boot configuration jumper
59 - Ethernet (RJ45 RMII interface)
60 - USB High Speed Host and Device (micro-AB connector)
61 - 512 Mb (64 MB) External Octo-SPI Flash (present in the MCU Native Pin Access area of the EK-RA8D1…
62 - CAN FD (3-pin header)
68 EK-RA8D1 Board Functional Area Definitions (Credit: Renesas Electronics Corporation)
81 Detail Hardware feature for the EK-RA8D1 MCU can be found at `EK-RA8D1 - User's Manual`_
86 The below features are currently supported on Zephyr OS for EK-RA8D1 board:
88 +--------------+------------+-----------------------------------+
91 | GPIO | on-chip | gpio |
92 +--------------+------------+-----------------------------------+
93 | MPU | on-chip | arch/arm |
94 +--------------+------------+-----------------------------------+
95 | NVIC | on-chip | arch/arm |
96 +--------------+------------+-----------------------------------+
97 | UART | on-chip | serial |
98 +--------------+------------+-----------------------------------+
99 | CLOCK | on-chip | clock control |
100 +--------------+------------+-----------------------------------+
101 | ENTROPY | on-chip | entropy |
102 +--------------+------------+-----------------------------------+
103 | SPI | on-chip | spi |
104 +--------------+------------+-----------------------------------+
105 | FLASH | on-chip | flash |
106 +--------------+------------+-----------------------------------+
107 | PWM | on-chip | pwm |
108 +--------------+------------+-----------------------------------+
109 | COUNTER | on-chip | counter |
110 +--------------+------------+-----------------------------------+
111 | CAN | on-chip | canfd |
112 +--------------+------------+-----------------------------------+
113 | I2C | on-chip | i2c |
114 +--------------+------------+-----------------------------------+
115 | USBHS | on-chip | udc |
116 +--------------+------------+-----------------------------------+
117 | DISPLAY | on-chip | LCDIF; MIPI-DSI. Tested with |
119 +--------------+------------+-----------------------------------+
120 | ETHERNET | on-chip | ethernet |
121 +--------------+------------+-----------------------------------+
122 | ADC | on-chip | adc |
123 +--------------+------------+-----------------------------------+
124 | SDHC | on-chip | sdhc |
125 +--------------+------------+-----------------------------------+
129 - For using Ethernet on RA8D1 board please set switch SW1 as following configuration:
131 +-------------+-------------+--------------+------------+------------+------------+-------------+--…
132 | SW1-1 PMOD1 | SW1-2 TRACE | SW1-3 CAMERA | SW1-4 ETHA | SW1-5 ETHB | SW1-6 GLCD | SW1-7 SDRAM | S…
133 +-------------+-------------+--------------+------------+------------+------------+-------------+--…
135 +-------------+-------------+--------------+------------+------------+------------+-------------+--…
137 - For using SDHC channel 1 on RA8D1 board please set switch SW1 as following configuration:
139 +-------------+-------------+--------------+------------+------------+------------+-------------+--…
140 | SW1-1 PMOD1 | SW1-2 TRACE | SW1-3 CAMERA | SW1-4 ETHA | SW1-5 ETHB | SW1-6 GLCD | SW1-7 SDRAM | S…
141 +-------------+-------------+--------------+------------+------------+------------+-------------+--…
143 +-------------+-------------+--------------+------------+------------+------------+-------------+--…
145 **CAUTION:** Do not enable SW1-4 and SW1-5 together
157 **Note:** Only support from SDK v0.16.6 in which GCC for Cortex Arm-M85 was available.
158 To build for EK-RA8M1 user need to get and install GNU Arm Embedded toolchain from https://github.c…
163 Program can be flashed to EK-RA8D1 via the on-board SEGGER J-Link debugger.
164 SEGGER J-link's drivers are avaialbe at https://www.segger.com/downloads/jlink/
168 1. Connect to J-Link OB via USB port to host PC
170 …2. Make sure J-Link OB jumper is in default configuration as describe in `EK-RA8D1 - User's Manual…
174 .. code-block:: console
176 west flash -r jlink
197 - `EK-RA8D1 Website`_
198 - `RA8D1 MCU group Website`_
200 .. _EK-RA8D1 Website:
201 …enesas.com/us/en/products/microcontrollers-microprocessors/ra-cortex-m-mcus/ek-ra8d1-evaluation-ki…
204 …roducts/microcontrollers-microprocessors/ra-cortex-m-mcus/ra8d1-480-mhz-arm-cortex-m85-based-graph…
206 .. _EK-RA8D1 - User's Manual:
207 https://www.renesas.com/us/en/document/mat/ek-ra8d1-v1-user-manual
210 https://www.renesas.com/us/en/document/mah/ra8d1-group-users-manual-hardware