Lines Matching +full:connector +full:- +full:control
9 The EK-RA6E2, an Evaluation Kit for RA6E2 MCU Group, enables users to
12 and e2 studio IDE. The users can use rich on-board features along with
13 their choice of popular ecosystems add-ons to bring their big ideas to life
15 The key features of the EK-RA6E2 board are categorized in three groups as follow:
19 - 200MHz Arm Cortex-M33 based RA6E2 MCU in 64 pins, LQFP package
20 - 256 kB Code Flash, 40 kB SRAM
21 - Native pin access through 2 x 14-pin and 1 x 40-pin male headers
22 - MCU current measurement points for precision current consumption measurement
23 - Multiple clock sources - RA6E2 MCU oscillator and sub-clock oscillator crystals,
27 **System Control and Ecosystem Access**
29 - USB Full Speed Host and Device (micro-AB connector)
30 - Three 5V input sources
32 - USB (Debug, Full Speed)
33 - External power supply (using surface mount clamp test points and J31 through holes)
35 - Three Debug modes
37 - Debug on-board (SWD)
38 - Debug in (SWD)
39 - Debug out (JTAG, SWD)
41 - User LEDs and buttons
43 - Three User LEDs (red, blue, green)
44 - Power LED (white) indicating availability of regulated power
45 - Debug LED (yellow) indicating the debug connection
46 - Two User buttons
47 - One Reset button
49 - Five most popular ecosystems expansions
51 - Two Seeed Grove system (I3C/Analog) connectors
52 - One SparkFun Qwiic connector
53 - Two Digilent Pmod (SPI and UART) connectors
54 - Arduino (Uno R3) connector
55 - MikroElektronika mikroBUS connector
57 - MCU boot configuration jumper
61 - 16 Mb (128 Mb) External Quad-SPI Flash
62 - CAN (3-pin header)
68 EK-RA6E2 Board Functional Area Definitions (Credit: Renesas Electronics Corporation)
81 Detailed hardware feature for the EK-RA6E2 MCU can be found at `EK-RA6E2 - User's Manual`_
86 The below features are currently supported on Zephyr OS for EK-RA6E2 board:
88 +-----------+------------+----------------------+
91 | GPIO | on-chip | gpio |
92 +-----------+------------+----------------------+
93 | MPU | on-chip | arch/arm |
94 +-----------+------------+----------------------+
95 | NVIC | on-chip | arch/arm |
96 +-----------+------------+----------------------+
97 | UART | on-chip | serial |
98 +-----------+------------+----------------------+
99 | CLOCK | on-chip | clock control |
100 +-----------+------------+----------------------+
101 | SPI | on-chip | spi |
102 +-----------+------------+----------------------+
103 | ADC | on-chip | adc |
104 +-----------+------------+----------------------+
105 | PWM | on-chip | pwm |
106 +-----------+------------+----------------------+
107 | ENTROPY | on-chip | entropy |
108 +-----------+------------+----------------------+
123 Program can be flashed to EK-RA6E2 via the on-board SEGGER J-Link debugger.
124 SEGGER J-link's drivers are avaialbe at https://www.segger.com/downloads/jlink/
128 1. Connect to J-Link OB via USB port to host PC
130 …2. Make sure J-Link OB jumper is in default configuration as describe in `EK-RA6E2 - User's Manual…
134 .. code-block:: console
136 west flash -r jlink
157 - `EK-RA6E2 Website`_
158 - `RA6E2 MCU group Website`_
160 .. _EK-RA6E2 Website:
161 …enesas.com/us/en/products/microcontrollers-microprocessors/ra-cortex-m-mcus/ek-ra6e2-evaluation-ki…
164 …/us/en/products/microcontrollers-microprocessors/ra-cortex-m-mcus/ra6e2-entry-line-200mhz-arm-cort…
166 .. _EK-RA6E2 - User's Manual:
167 https://www.renesas.com/us/en/document/mat/ek-ra6e2-v1-users-manual
170 https://www.renesas.com/us/en/document/mah/ra6e2-group-users-manual-hardware