Lines Matching +full:chip +full:- +full:specific
9 The EK-RA2A1 is an evaluation kit for Renesas RA2A1 Microcontroller Group.
13 - 48MHz, Arm Cortex-M23 core
14 - 256kB Code Flash, 8kB Data Flash, 32kB SRAM
15 - USB 2.0 Full-Sppeed
16 - SCI x 3
17 - SPI x 2
18 - I2C x 2
19 - CAN x 1
20 - 16-bit A/D Converter
21 - 24-bit Sigma-Delta A/D Converter
22 - 12-bit D/A Converter
23 - 8-bit D/A Converter x 2
24 - High-Speed Analog Comparator
25 - Low-Power Analog Comparator
26 - OPAMP x 3
27 - Temperature Sensor
28 - General PWM Timer 32-bit x 1
29 - General PWM Timer 16-bit x 6
30 - Low Power Asynchronous General-Purpose Timer x 2
31 - Watchdog Timer
32 - 49 Input/Output pins
38 EK-RA2A1 Board Functional Area Definitions (Credit: Renesas Electronics Corporation)
52 Detail Hardware feature for the EK-RA2A1 MCU can be found at `EK-RA2A1 - User's Manual`_
54 EK-RA2A1 has following features.
56 - Native pin access through 4x 40-pin male headers
57 - MCU current measurement points
58 - SEGGER J-Link on-board programmer and debugger
59 - Two Digilent Pmod (SPI and UART)
60 - User LED
61 - Mechanical user button
62 - Capacitive user button
67 The Renesas EK-RA2A1 board configuration supports the following
70 +-----------+------------+-------------------------------+
73 | PINCTRL | on-chip | pinctrl |
74 +-----------+------------+-------------------------------+
75 | CLOCK | on-chip | clock_control |
76 +-----------+------------+-------------------------------+
77 | GPIO | on-chip | gpio |
78 +-----------+------------+-------------------------------+
79 | UART | on-chip | uart |
80 +-----------+------------+-------------------------------+
81 | SPI | on-chip | spi |
82 +-----------+------------+-------------------------------+
83 | COUNTER | on-chip | counter |
84 +-----------+------------+-------------------------------+
85 | PWM | on-chip | pwm |
86 +-----------+------------+-------------------------------+
87 | ENTROPY | on-chip | entropy |
88 +-----------+------------+-------------------------------+
89 | I2C | on-chip | i2c |
90 +-----------+------------+-------------------------------+
102 You can build and flash an application with onboard J-Link debug adapter.
106 Here is an example for building and flashing the :zephyr:code-sample:`blinky` application.
108 .. zephyr-app-commands::
109 :zephyr-app: samples/basic/blinky
117 Debugging also can be done with onboard J-Link debug adapter.
118 The following command is debugging the :zephyr:code-sample:`blinky` application.
119 Also, see the instructions specific to the debug server that you use.
121 .. zephyr-app-commands::
122 :zephyr-app: samples/basic/blinky
124 :maybe-skip-config:
131 .. target-notes::
133 .. EK-RA2A1 Web site:
134 …enesas.com/us/en/products/microcontrollers-microprocessors/ra-cortex-m-mcus/ek-ra2a1-evaluation-ki…
137 https://www.renesas.com/en/document/mah/renesas-ra2a1-group-users-manual-hardware
139 .. _EK-RA2A1 - User's Manual:
140 https://www.renesas.com/en/document/mah/renesas-ra2a1-group-users-manual-hardware