Lines Matching refs:board
3 reel board
9 `reel board`_ is a evaluation board based on the Nordic Semiconductor
10 nRF52840 SoC. The board was developed by PHYTEC Messtechnik GmbH in
12 The board has a built-in debug adapter based on the DAPLink interface
27 The board provides support for the Nordic Semiconductor nRF52840 ARM |reg|
31 The schematic can be found on the `reel board website`_.
36 On the front of the board are RGB-LED, ADPS9960 and HDC1010 sensors,
41 On the back side of the board are all other components such as nRF52840,
53 :alt: reel board front
55 reel board front (Credit: PHYTEC)
59 :alt: reel board back
61 reel board back (Credit: PHYTEC)
64 the board but integrated as a module on a NOTM.2 adapter.
72 GDEH0213B1 is the display with which the board was introduced
74 Currently the board is delivered with the display GDEH0213B72.
77 The following table lists the displays used on the reel board.
95 The board is optimized for low power applications and supports two
100 reel board uses a TPS610981 boost converter to generate supply voltage
112 :zephyr_file:`boards/phytec/reel_board/board.c`
117 The reel_board board configuration supports the following
147 Other hardware features have not been enabled yet for this board.
265 There are several labeled solder jumpers on the board.
271 :alt: reel board Jumper and Testpoints
273 reel board testpoints (Credit: PHYTEC)
333 is always on when the board is connected to the USB host.
334 reel board can be flashed and debugged, powered either from battery or USB.
335 If the Adapter is powered via USB, the Adapter circuit heats the board
340 :alt: reel board Debug Adapter
342 reel board Debug Adapter overview (Credit: PHYTEC)
347 DAPLink firmware for the adapter can be found at `DAPLink reel board Firmware`_.
349 mode. For this, the board should be disconnected from the USB host,
350 the J22 should be closed (use tweezers for this) and the board reconnected to
384 designed especially for the reel board are called link boards.
388 :alt: reel board Expansion Connector
390 reel board Expansion Connector (Credit: PHYTEC)
392 link board BASE
395 link board BASE is a passive expansion board and allows other link boards or
396 third party shields in Arduino UNO R3 format to be connected to the reel board.
398 then reel board.
402 :alt: reel board and link board BASE
404 reel board and link board BASE (Credit: PHYTEC)
406 link board BASE can be used in combination with other link boards or
410 reel board is plugged into the link board BASE. Both peripherals on
411 reel board and shields can be used as long as there is no conflict
416 NOTM.2 adapter is removed from the reel board and
417 connected to NOTM.2 connector on the link board BASE.
422 peripherals on the reel board are not used or in conflict,
423 power provided by the reel board is not enough,
428 :alt: link board BASE
430 link board BASE (Credit: PHYTEC)
432 Components on the link board BASE:
434 reel board Connector:
443 reel board should be removed from reel board connector.
461 link board BASE is powered from Alternative Power Source Connector
465 link board BASE is powered from USB connector (via DCDC converter).
468 link board BASE is powered from reel board. The available power is
469 below 0.3W and depends on which source is used to power the reel board.
474 Applications for the ``reel_board`` board configuration can be
494 Finally, unplug and plug the board again for the rules to take effect.
508 Replace :code:`<tty_device>` with the port where the reel board
515 :board: reel_board
519 Please use reel_board@2 to build a application for the board equipped with
524 :board: reel_board@2
535 :board: reel_board
544 LEDs on the board are working properly with Zephyr:
550 your board.
557 .. _reel board Website:
562 .. _reel board:
565 .. _DAPLink reel board Firmware:
566 https://github.com/PHYTEC-Messtechnik-GmbH/DAPLink/tree/reel-board