Lines Matching +full:flexcan +full:- +full:fd
6 FRDM-MCXN236 are compact and scalable development boards for rapid prototyping of
8 MCUs I/Os, integrated open-standard serial interfaces, external flash memory and
9 an on-board MCU-Link debugger. MCX N Series are high-performance, low-power
10 microcontrollers with intelligent peripherals and accelerators providing multi-tasking
16 - MCX-N236 Arm Cortex-M33 microcontroller running at 150 MHz
17 - 1MB dual-bank on chip Flash
18 - 352 KB RAM
19 - USB high-speed (Host/Device) with on-chip HS PHY. HS USB Type-C connectors
20 - 8x LP Flexcomms each supporting SPI, I2C, UART
21 - 2x FlexCAN with FD, 2x I3Cs, 2x SAI
22 - On-board MCU-Link debugger with CMSIS-DAP
23 - Arduino Header, FlexIO/LCD Header, SmartDMA/Camera Header, mikroBUS
25 For more information about the MCX-N236 SoC and FRDM-MCXN236 board, see:
27 - `MCX-N236 SoC Website`_
28 - `MCX-N236 Datasheet`_
29 - `MCX-N236 Reference Manual`_
30 - `FRDM-MCXN236 Website`_
31 - `FRDM-MCXN236 User Guide`_
32 - `FRDM-MCXN236 Board User Manual`_
33 - `FRDM-MCXN236 Schematics`_
38 The FRDM-MCXN236 board configuration supports the following hardware features:
40 +-----------+------------+-------------------------------------+
43 | NVIC | on-chip | nested vector interrupt controller |
44 +-----------+------------+-------------------------------------+
45 | SYSTICK | on-chip | systick |
46 +-----------+------------+-------------------------------------+
47 | PINMUX | on-chip | pinmux |
48 +-----------+------------+-------------------------------------+
49 | GPIO | on-chip | gpio |
50 +-----------+------------+-------------------------------------+
51 | UART | on-chip | serial port-polling; |
52 | | | serial port-interrupt |
53 +-----------+------------+-------------------------------------+
54 | SPI | on-chip | spi |
55 +-----------+------------+-------------------------------------+
56 | I2C | on-chip | i2c |
57 +-----------+------------+-------------------------------------+
58 | CLOCK | on-chip | clock_control |
59 +-----------+------------+-------------------------------------+
60 | FLASH | on-chip | soc flash |
61 +-----------+------------+-------------------------------------+
62 | WATCHDOG | on-chip | watchdog |
63 +-----------+------------+-------------------------------------+
64 | VREF | on-chip | regulator |
65 +-----------+------------+-------------------------------------+
66 | ADC | on-chip | adc |
67 +-----------+------------+-------------------------------------+
68 | USBHS | on-chip | USB device |
69 +-----------+------------+-------------------------------------+
70 | LPCMP | on-chip | sensor(comparator) |
71 +-----------+------------+-------------------------------------+
72 | FLEXCAN | on-chip | CAN |
73 +-----------+------------+-------------------------------------+
74 | FLEXIO | on-chip | flexio |
75 +-----------+------------+-------------------------------------+
76 | DISPLAY | on-chip | flexio; MIPI-DBI. Tested with |
78 +-----------+------------+-------------------------------------+
79 | LPTMR | on-chip | counter |
80 +-----------+------------+-------------------------------------+
81 | MRT | on-chip | counter |
82 +-----------+------------+-------------------------------------+
83 | RTC | on-chip | rtc |
84 +-----------+------------+-------------------------------------+
97 The MCX-N236 SoC has 6 gpio controllers and has pinmux registers which
100 +------------+-----------------+----------------------------+
104 +------------+-----------------+----------------------------+
106 +------------+-----------------+----------------------------+
111 The MCX-N236 SoC is configured to use PLL0 running at 150MHz as a source for
117 The FRDM-MCXN236 SoC has 8 FLEXCOMM interfaces for serial communication.
130 configured by default to use the MCU-Link CMSIS-DAP Onboard Debug Probe.
133 ----------------
136 default MCU-Link firmware. Follow the instructions in
137 :ref:`mcu-link-cmsis-onboard-debug-probe` to reprogram the default MCU-Link
142 Using J-Link
143 ------------
146 J-Link firmware by following the instructions in
147 :ref:`mcu-link-jlink-onboard-debug-probe`.
150 The second option is to attach a :ref:`jlink-external-debug-probe` to the
151 10-pin SWD connector (J12) of the board. Additionally, the jumper JP7 must
153 For both options use the ``-r jlink`` option with west to use the jlink runner.
155 .. code-block:: console
157 west flash -r jlink
165 - Speed: 115200
166 - Data: 8 bits
167 - Parity: None
168 - Stop bits: 1
173 Here is an example for the :zephyr:code-sample:`hello_world` application.
175 .. zephyr-app-commands::
176 :zephyr-app: samples/hello_world
183 .. code-block:: console
185 *** Booting Zephyr OS build v3.6.0-4478-ge6c3a42f5f52 ***
191 Here is an example for the :zephyr:code-sample:`hello_world` application.
193 .. zephyr-app-commands::
194 :zephyr-app: samples/hello_world
201 .. code-block:: console
203 *** Booting Zephyr OS build v3.6.0-4478-ge6c3a42f5f52 ***
209 .. include:: ../../common/segger-ecc-systemview.rst
210 :start-after: segger-ecc-systemview
212 .. _MCX-N236 SoC Website:
213 …-and-microcontrollers/arm-microcontrollers/general-purpose-mcus/mcx-arm-cortex-m/mcx-n-series-micr…
215 .. _MCX-N236 Datasheet:
216 https://www.nxp.com/docs/en/data-sheet/MCXN23x.pdf
218 .. _MCX-N236 Reference Manual:
219 https://www.nxp.com/docs/en/reference-manual/MCXN23xRM.pdf
221 .. _FRDM-MCXN236 Website:
222 …w.nxp.com/design/design-center/development-boards-and-designs/general-purpose-mcus/frdm-developmen…
224 .. _FRDM-MCXN236 User Guide:
225 https://www.nxp.com/document/guide/getting-started-with-frdm-mcxn236:GS-FRDM-MCXN236
227 .. _FRDM-MCXN236 Board User Manual:
228 https://www.nxp.com/docs/en/user-manual/UM12041.pdf
230 .. _FRDM-MCXN236 Schematics:
231 https://www.nxp.com/webapp/Download?colCode=SPF-90828