Lines Matching +full:dev +full:- +full:density
12 - MEC172x (MEC1723, MEC1727 and MEC1728) ARM Cortex-M4 Processor
13 - 416 KB RAM and 128 KB boot ROM
14 - UART1 using microUSB
15 - PECI interface 3.0
16 - FAN, PWM and TACHO pins
17 - 5 SMBus instances
18 - eSPI header
19 - VCI interface
20 - 1 hardware driven PS/2 ports
21 - Keyboard interface headers
29 - GPIOs
30 - JTAG port
31 - eSPI bus
32 - I2C0, I2C1 and I2C6
33 - PWM1, PWM2, PWM3
34 - Shared SPI
35 - Keyboard Interface
37 2) Mated mode with another platform that has a high density MECC connector
39 - FAN, PWM8
40 - I2C3 and I2C7
41 - eSPI bus
43 The board is powered through the +5V USB micro-A connector or from the MECC connector.
49 .. zephyr:board-supported-hw::
56 - MEC172x Modular ASSY 6930 Rev B1 `MEC172x Modular EC Card - Assy_6930 Rev B1p1`_
62 on-chip PLL to generate a resulting EC clock rate of 12 MHz. See Processor clock
80 Power-Related Jumpers
81 ---------------------
82 If you wish to power from type A/B connector ``P1`` set the jumper ``JP22 1-2``.
85 set the jumper to ``JP22 2-3``.
89 If you wish to set VTR2 to 3.3V, set the jumper ``JP26 2-3``.
91 If you wish to set VTR2 to 1.8V, set the jumper ``JP26 1-2``.
94 Boot-ROM Straps
95 ---------------
96 This jumper configures MEC172x Boot-ROM strap.
98 +---------------------+
101 | 1-2 |
102 +---------------------+
104 ``JP23 1-2`` pulls UART_BSTRAP to GND. MEC172x Boot-ROM samples UART_BSTRAP and if low,
108 ------------------
112 +-------------------+----------+
115 | Shared SPI or SAF | 5-6 |
116 +-------------------+----------+
117 | MAF | 1-2, 4-6 |
118 +-------------------+----------+
133 For Linux please make sure that you copied ``60-dediprog.rules``
137 .. code-block:: console
139 $ udevadm control --reload
150 .. code-block:: console
152 -DMEC172X_SPI_GEN=<path to spi_gen tool>/mec172x_spi_gen_lin_x86_64
161 .. code-block:: console
163 -DMEC172X_SPI_CFG=<path to spi_cfg file>/spi_cfg.txt
167 .. code-block:: console
169 …ld -p auto -b mec172xmodular_assy6930 samples/hello_world -- -DMEC172X_SPI_GEN=$HOME/CPGZephyrDocs…
179 +------------+---------------+
184 +------------+---------------+
186 +------------+---------------+
188 +------------+---------------+
190 +------------+---------------+
192 +------------+---------------+
194 +------------+---------------+
199 #. Apply power to the board via a micro-USB cable.
200 Configure this option by using a jumper between ``JP22 1-2``.
205 #. Build :zephyr:code-sample:`hello_world` application as you would normally do.
215 Under Linux the terminal should be :code:`/dev/ttyUSB0`. Do not close it.
219 .. code-block:: console
221 $ minicom -D /dev/ttyUSB0 -o
223 The -o option tells minicom not to send the modem initialization
226 - Speed: 115200
227 - Data: 8 bits
228 - Parity: None
229 - Stop bits: 1
234 .. code-block:: console
251 If ``LED1`` is off, check the power-related jumpers again.
261 .. target-notes::
264 https://github.com/MicrochipTech/CPGZephyrDocs/blob/master/MEC172x/MEC172x-Data-Sheet.pdf
265 .. _MEC172x Modular EC Card - Assy_6930 Rev B1p1:
266 …https://github.com/MicrochipTech/CPGZephyrDocs/blob/master/MEC172x/MEC172X-MECC_Assy_6930_B1p1-SCH…