Lines Matching +full:dev +full:- +full:density
13 - MEC1521HA0SZ ARM Cortex-M4 Processor
14 - 256 KB RAM and 64 KB boot ROM
15 - GPIO headers
16 - UART1 using microUSB
17 - PECI interface 3.0
18 - 10 SMBUS instances
19 - FAN, PMW and TACHO pins
20 - VCI interface
21 - Independent Hardware Driven PS/2 Ports
28 - GPIOs
29 - PWM5
30 - JTAG/SWD, ETM and MCHP Trace ports
31 - eSPI bus
32 - SMB0
34 2) Mated mode with another platform that has a high density MECC connector.
36 - FAN0, PWM0, SMB0, SMB1, SMB4 and SMB5
37 - eSPI bus
38 - Breathing/Blinking LEDs
51 +-----------+------------+-------------------------------------+
54 | NVIC | on-chip | nested vector interrupt controller |
55 +-----------+------------+-------------------------------------+
56 | SYSTICK | on-chip | systick |
57 +-----------+------------+-------------------------------------+
58 | UART | on-chip | serial port |
59 +-----------+------------+-------------------------------------+
60 | GPIO | on-chip | gpio |
61 +-----------+------------+-------------------------------------+
62 | ESPI | on-chip | espi |
63 +-----------+------------+-------------------------------------+
64 | I2C | on-chip | i2c |
65 +-----------+------------+-------------------------------------+
66 | PINMUX | on-chip | pinmux |
67 +-----------+------------+-------------------------------------+
68 | RTOS | on-chip | timer |
69 +-----------+------------+-------------------------------------+
70 | TIMER | on-chip | counter |
71 +-----------+------------+-------------------------------------+
72 | PWM | on-chip | pwm |
73 +-----------+------------+-------------------------------------+
74 | ADC | on-chip | adc |
75 +-----------+------------+-------------------------------------+
76 | WATCHDOG | on-chip | watchdog |
77 +-----------+------------+-------------------------------------+
78 | PS2 | on-chip | ps2 |
79 +-----------+------------+-------------------------------------+
92 - MEC1501 Modular Card ASSY 6885 Rev A0 `MEC1501 Modular EC Card - Assy_6885 Rev A0p1`_
98 on-chip PLL to generate a resulting EC clock rate of 12 MHz. See Processor clock
115 Power-related jumpers
116 ---------------------
118 If you wish to power from type A/B connector ``P10`` set the jumper ``JP35 1-2``.
121 set the jumper to ``JP35 3-4``.
125 +------+---------+---------+------+------+------+----------+
129 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 |
130 +------+---------+---------+------+------+------+----------+
133 +------+------------+------+----------+
137 | 2-3 | 1-2 | 2-3 | open |
138 +------+------------+------+----------+
142 +-----------+---------------+
146 | 11-12 | 1-2 |
147 +-----------+---------------+
149 Boot-ROM Straps
150 ---------------
152 These jumpers configure MEC1501 Boot-ROM straps.
154 +-------------+------------+--------------+-------------+
158 | 1-2 | 1-2 | 1-2 | 3-4 |
159 +-------------+------------+--------------+-------------+
162 ``JP23 3-4`` pulls SHD SPI CS0# up to VTR2. MEC1501 Boot-ROM samples
166 +-------------+------------+----------------------------+
168 +-------------+------------+----------------------------+
170 +-------------+------------+----------------------------+
172 +-------------+------------+----------------------------+
174 +-------------+------------+----------------------------+
177 ----------------
178 ``JP20 2-3`` is required so all GPIOs powered by VTR3 rail worked at 1.8V.
182 +-------------------+-----------------+
186 | 2-3 | 1.8V to pin 1 |
187 +-------------------+-----------------+
191 -------------------
193 .. code-block:: none
195 +--------------------------------------------------------------------------------------+
196 | |------------| +----------+ J10 || |
197 | [BT1] + +------------+ J50 ++ ++ || |
199 | + + + +-+ JP4 + + JP26 || || |
201 | JP31 ++ JP32 JP36 +-+ JP27 + + + + J6 || |
203 | ++ + + +--------+ J48 |
204 | || JP21 + + +--------+ JP22 +----------+ |
207 | ++ +----------------+ || |
208 | +---------------+ || + JP24 |----------------| ++ |
209 | |---------------| ++ + +----------+ +----------------+ J47 |
210 | JP20 +---------------+ JP23 JP40 +----------+ ++ |
212 | + + +----------+ + || |
213 | J52+---------------+ + + +----------+ J5 +-------------+ ++ |
214 | J45+---------------+ JP33 TP57 JP25 +-------------+ J4 J49 |
216 | ++ TP4 +----------+ ++ |
217 | ++ + + + + + + TP61 +----------+ ++ |
222 +--------------------------------------------------------------------------------------+
232 that directory. For the pre-production MEC150x use the `MEC150x SPI Image Gen`_
239 .. code-block:: console
244 For the pre-production MEC1501 SOC use everglades_spi_gen_lin64.
249 .. code-block:: console
256 #. Build :zephyr:code-sample:`hello_world` application as you would normally do.
271 terminal should be :code:`/dev/ttyACM0`. For example:
273 .. code-block:: console
275 $ minicom -D /dev/ttyACM0 -o
277 The -o option tells minicom not to send the modem initialization
280 - Speed: 115200
281 - Data: 8 bits
282 - Parity: None
283 - Stop bits: 1
303 .. target-notes::
309 .. _MEC1501 Modular EC Card - Assy_6885 Rev A0p1:
310 …phyrDocs/blob/master/MEC1501/MEC1501%20Modular%20EC%20Card%20-%20Assy_6885%20Rev%20A0p1%20-%20SCH.…