Lines Matching +full:dual +full:- +full:supply
6 M5Stack StampS3 is an ESP32-based development board from M5Stack.
9 - ESP32-S3FN8 chip (240MHz dual core)
10 - 512KB SRAM
11 - 384KB ROM
12 - 8MB Flash
13 - Wi-Fi
14 - Bluetooth
15 - User-Button
23 +---------------+-----------------------------------------------------------------+-----------+
26 | ESP32-S3FN8 | This MPU-ESP32S3 module provides complete Wi-Fi and Bluetooth | supported |
28 +---------------+-----------------------------------------------------------------+-----------+
29 | Status LED | One user LED connected via :dtcompatible:`worldsemi,ws2812-spi` | supported |
30 | | interface (``led-strip``). | |
31 +---------------+-----------------------------------------------------------------+-----------+
32 | USB Port | USB interface. Power supply for the board as well as the | supported |
34 +---------------+-----------------------------------------------------------------+-----------+
36 +---------------+-----------------------------------------------------------------+-----------+
43 :dtcompatible:`m5stack,stamps3-header`.
54 - ``m5stack_stamps3_clkout0``: PWM output with 2 channels (0 and 2).
55 - ``m5stack_stamps3_spilcd``: SPI interface for interfacing LCDs. Consists of a
57 - ``m5stack_stamps3_i2c0`` and ``m5stack_stamps3_i2c1``: I2C interfaces (SDA, SCL).
58 - ``m5stack_stamps3_uart0``: UART interface (RXD, TXD).
59 - ``m5stack_stamps3_header``: All GPIOs are of course accessible via main header
62 +-----+-----------------------------------------+-----+---------------------------------+
66 +-----+-----------------------------------------+-----+---------------------------------+
68 +-----+-----------------------------------------+-----+---------------------------------+
69 | 3 | ``m5stack_stamps3_clkout0`` - Channel 0 | | |
70 +-----+-----------------------------------------+-----+---------------------------------+
72 +-----+-----------------------------------------+-----+---------------------------------+
73 | 5 | ``m5stack_stamps3_spilcd`` - MOSI | | |
74 +-----+-----------------------------------------+-----+---------------------------------+
75 | 6 | ``m5stack_stamps3_spilcd`` - CLK | | |
76 +-----+-----------------------------------------+-----+---------------------------------+
77 | 7 | ``m5stack_stamps3_spilcd`` - CS | 28 | **3V3** |
78 +-----+-----------------------------------------+-----+---------------------------------+
79 | 8 | | 27 | ``m5stack_stamps3_uart0`` - TXD |
80 +-----+-----------------------------------------+-----+---------------------------------+
81 | 9 | ``m5stack_stamps3_clkout0`` - Channel 2 | 26 | |
82 +-----+-----------------------------------------+-----+---------------------------------+
83 | 10 | | 25 | ``m5stack_stamps3_uart0`` - RXD |
84 +-----+-----------------------------------------+-----+---------------------------------+
86 +-----+-----------------------------------------+-----+---------------------------------+
87 | 12 | ``m5stack_stamps3_i2c1`` - SDA | 23 | |
88 +-----+-----------------------------------------+-----+---------------------------------+
90 +-----+-----------------------------------------+-----+---------------------------------+
91 | 14 | ``m5stack_stamps3_i2c1`` - SCL | 21 | |
92 +-----+-----------------------------------------+-----+---------------------------------+
93 | 15 | ``m5stack_stamps3_i2c0`` - SDA | 20 | |
94 +-----+-----------------------------------------+-----+---------------------------------+
96 +-----+-----------------------------------------+-----+---------------------------------+
97 | 17 | ``m5stack_stamps3_i2c0`` - SCL | 18 | **GND** |
98 +-----+-----------------------------------------+-----+---------------------------------+
100 Power supply
103 M5Stack StampS3 requires a single 5V input power supply. The module internally
104 features a DCDC (MUN3CAD01-SC) to generate the 3.3V needed for the MCU.
107 supply. If this pin is pulled low this main 3.3V power supply for the MCU will be
108 deactivated. It is internally equipped with a pull-up and can hence be left open
121 -------------
126 .. code-block:: console
135 -------------------
140 .. zephyr-app-commands::
141 :zephyr-app: samples/hello_world
146 configuration. Here is an example for the :zephyr:code-sample:`hello_world`
149 .. zephyr-app-commands::
150 :zephyr-app: samples/hello_world
155 try using different values by using ``--esp-baud-rate <BAUD>`` option during
156 ``west flash`` (e.g. ``west flash --esp-baud-rate 115200``).
160 .. code-block:: shell
167 .. code-block:: console
169 ***** Booting Zephyr OS vx.x.x-xxx-gxxxxxxxxxxxx *****
173 ---------
175 M5Stack StampS3 exports a JTAG-interface via Pins 19 (MTCK), 21 (MTDO), 23
186 - `M5Stack StampS3 schematic <https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/docs/datasheet/…
187 - `M5Stack StampS3 <https://docs.m5stack.com/en/core/StampS3>`_
188 - `ESP32 Datasheet <https://www.espressif.com/sites/default/files/documentation/esp32_datasheet_en.…
189 - `ESP32 Hardware Reference <https://docs.espressif.com/projects/esp-idf/en/latest/esp32/hw-referen…