Lines Matching full:ethernet

6 The ESP32-Ethernet-Kit is an Ethernet-to-Wi-Fi development board that enables
7 Ethernet devices to be interconnected over Wi-Fi. At the same time, to provide
8 more flexible power supply options, the ESP32-Ethernet-Kit also supports power
9 over Ethernet (PoE).
11 .. _get-started-esp32-ethernet-kit-v1.2-overview:
13 ESP32-Ethernet-Kit is an ESP32-WROVER-E based development.
16 It consists of two development boards, the Ethernet Board A and the PoE
17 board B. The `Ethernet Board (A)`_ contains Bluetooth/Wi-Fi dual-mode
18 ESP32-WROVER-E module and IP101GRI, a Single Port 10/100 Fast Ethernet
19 Transceiver (PHY). The `PoE Board (B)`_ provides power over Ethernet
23 .. _get-started-esp32-ethernet-kit-v1.2:
25 .. figure:: img/esp32-ethernet-kit-v1.2.jpg
27     :alt: ESP32-Ethernet-Kit V1.2
30     ESP32-Ethernet-Kit V1.2
32 For the application loading and monitoring, the Ethernet Board (A) also
41 The block diagram below shows the main components of ESP32-Ethernet-Kit
44 .. figure:: img/esp32-ethernet-kit-v1.1-block-diagram.jpg
46     :alt: ESP32-Ethernet-Kit block diagram
49     ESP32-Ethernet-Kit block diagram
56 and controls of the ESP32-Ethernet-Kit.
58 .. _get-started-esp32-ethernet-kit-a-v1.2-layout:
61 Ethernet Board (A)
64 .. figure:: img/esp32-ethernet-kit-a-v1.2-layout.jpg
66     :alt: ESP32-Ethernet-Kit V1.2
69     ESP32-Ethernet-Kit - Ethernet Board (A) layout
97       development and debugging. See `ESP32-Ethernet-Kit V1.2 Ethernet Board (A) Schematic`_
115     - The physical layer (PHY) connection to the Ethernet cable is
124     - Ethernet network data transmission port.
126     - The Magnetics are part of the Ethernet specification to protect against
129       galvanic isolation between the transceiver and the Ethernet device.
146 This board coverts power delivered over the Ethernet cable (PoE) to provide a
147 power supply for the Ethernet Board (A). The main components of the PoE Board
155 To take advantage of the PoE functionality the **RJ45 Port** of the Ethernet
156 board (A) should be connected with an Ethernet cable to a switch that supports
157 PoE. When the Ethernet Board (A) detects 5 V power output from the PoE Board
160 .. figure:: img/esp32-ethernet-kit-b-v1.0-layout.jpg
162     :alt: ESP32-Ethernet-Kit - PoE Board (B)
165     ESP32-Ethernet-Kit - PoE Board (B) layout
175       PoE Board (B) to `Ethernet Board (A)`_. The pins on the left accept
177       supply to the Ethernet Board (A).
181 .. _get-started-esp32-ethernet-kit-v1.2-setup-options:
187 This section describes options to configure the ESP32-Ethernet-Kit hardware.
210 The ethernet MAC and PHY under RMII working mode need a common 50 MHz
217     `ESP32-Ethernet-Kit V1.2 Ethernet Board (A) Schematic`_, sheet 2, location D2.
222 By default, the ESP32-Ethernet-Kit is configured to provide RMII clock for the
227 .. figure:: img/esp32-ethernet-kit-rmii-clk-from-phy.jpg
248 .. figure:: img/esp32-ethernet-kit-rmii-clk-to-phy.jpg
257 `ESP32-Ethernet-Kit V1.2 Ethernet Board (A) Schematic`_,
267 functions of the ESP32-Ethernet-Kit.
274 below. Implementation of ESP32-Ethernet-Kit defaults to Reduced
312 ESP32-Ethernet-Kit.
401        `ESP32-Ethernet-Kit V1.2 Ethernet Board (A) Schematic`_.
572 Enabling Ethernet
575 Enable Ethernet MAC, PHY and MDIO; add these to your device tree overlay:
591 Enable Ethernet in KConfig:
602 RESET_N (GPIO5) is automatically set high to enable the Ethernet PHY
610 .. _`ESP32-Ethernet-Kit V1.2 Ethernet Board (A) Schematic`: https://dl.espressif.com/dl/schematics/…