Lines Matching +full:standby +full:- +full:gpios
6 The Dragino NBSN95 NB-IoT Sensor Node for IoT allows users to develop
7 applications with NB-IoT connectivity via the Quectel BC95-G.
9 low-power communication, ARM |reg| Cortex |reg|-M0 core-based
14 - STM32L072CZ MCU
15 - Quectel BC95-G NB-IoT
16 - Expansion connectors:
17 - PMOD
18 - Li/SOCI2 Unchargable Battery
19 - GPIOs exposed via screw terminals on the carrier board
20 - Housing
29 - Ultra-low-power (down to 0.29 µA Standby mode and 93 uA/MHz run mode)
30 - Core: ARM |reg| 32-bit Cortex |reg|-M0+ CPU, frequency up to 32 MHz
31 - Clock Sources:
33 - 1 to 32 MHz crystal oscillator
34 - 32 kHz crystal oscillator for RTC (LSE)
35 - Internal 16 MHz factory-trimmed RC ( |plusminus| 1%)
36 - Internal low-power 37 kHz RC ( |plusminus| 5%)
37 - Internal multispeed low-power 65 kHz to 4.2 MHz RC
38 - RTC with HW calendar, alarms and calibration
39 - Up to 24 capacitive sensing channels: support touchkey, linear and rotary touch sensors
40 - 11x timers:
42 - 2x 16-bit with up to 4 channels
43 - 2x 16-bit with up to 2 channels
44 - 1x 16-bit ultra-low-power timer
45 - 1x SysTick
46 - 1x RTC
47 - 2x 16-bit basic for DAC
48 - 2x watchdogs (independent/window)
49 - Up to 84 fast I/Os, most 5 V-tolerant.
50 - Memories
52 - Up to 192 KB Flash, 2 banks read-while-write, proprietary code readout protection
53 - Up to 20 KB of SRAM
54 … - External memory interface for static memories supporting SRAM, PSRAM, NOR and NAND memories
55 - Rich analog peripherals (independent supply)
57 - 1x 12-bit ADC 1.14 MSPS
58 - 2x 12-bit DAC
59 - 2x ultra-low-power comparators
60 - 11x communication interfaces
62 - USB OTG 2.0 full-speed, LPM and BCD
63 - 3x I2C FM+(1 Mbit/s), SMBus/PMBus
64 - 4x USARTs (ISO 7816, LIN, IrDA, modem)
65 - 6x SPIs (4x SPIs with the Quad SPI)
66 - 7-channel DMA controller
67 - True random number generator
68 - CRC calculation unit, 96-bit unique ID
69 - Development support: serial wire debug (SWD), JTAG, Embedded Trace Macrocell |trade|
74 - `STM32L072CZ on www.st.com`_
75 - `STM32L0x2 reference manual`_
82 +-----------+------------+-------------------------------------+
85 | UART | on-chip | serial port-polling; |
86 | | | serial port-interrupt |
87 +-----------+------------+-------------------------------------+
88 | PINMUX | on-chip | pinmux |
89 +-----------+------------+-------------------------------------+
90 | GPIO | on-chip | gpio |
91 +-----------+------------+-------------------------------------+
103 input/output, pull-up, etc.
106 ---------------
111 ----------------------------------
113 - UART_1_TX : PB6
114 - UART_1_RX : PB7
115 - UART_2_TX : PA2
116 - UART_2_RX : PA3
119 ------------
124 -----------
142 -----------------------------------------
144 Here is an example for the :zephyr:code-sample:`hello_world` application.
149 .. code-block:: console
151 $ minicom -D /dev/ttyACM0
155 .. zephyr-app-commands::
156 :zephyr-app: samples/hello_world
162 .. code-block:: console
170 :zephyr:code-sample:`hello_world` application.
172 .. zephyr-app-commands::
173 :zephyr-app: samples/hello_world
175 :maybe-skip-config:
179 https://www.dragino.com/products/nb-iot/item/163-nbsn95.html