| /Linux-v6.6/Documentation/devicetree/bindings/media/i2c/ |
| D | ov7670.txt | 13 - hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
14 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
|
| D | tvp5150.txt | 44 - hsync-active: Active state of the HSYNC signal. Must be <1> (HIGH).
45 - vsync-active: Active state of the VSYNC signal. Must be <1> (HIGH).
|
| /Linux-v6.6/arch/arm64/boot/dts/renesas/ |
| D | hihope-rzg2-ex-lvds.dtsi | 21 * When GP1_20 is HIGH LVDS0 is connected to the LT8918L
|
| /Linux-v6.6/include/linux/mfd/ |
| D | tps65010.h | 124 #define HIGH 1 macro
|
| /Linux-v6.6/arch/arm/boot/dts/rockchip/ |
| D | rk3228-evb.dts | 67 rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
|
| D | rk3288-rock2-som.dtsi | 251 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
|
| D | rk3288-evb.dtsi | 301 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
|
| /Linux-v6.6/Documentation/devicetree/bindings/clock/ |
| D | silabs,si5351.txt | 55 1 = clock output is driven HIGH when disabled
56 2 = clock output is FLOATING (HIGH-Z) when disabled
|
| /Linux-v6.6/drivers/s390/crypto/ |
| D | zcrypt_msgtype6.h | 108 #define HIGH 500 macro
|
| /Linux-v6.6/Documentation/userspace-api/media/cec/ |
| D | cec-ioc-dqevent.rst | 160 * .. _`CEC-EVENT-PIN-CEC-HIGH`:
176 * .. _`CEC-EVENT-PIN-HPD-HIGH`:
194 * .. _`CEC-EVENT-PIN-5V-HIGH`:
|
| /Linux-v6.6/arch/arm/boot/dts/nxp/imx/ |
| D | imx6qdl-mba6.dtsi | 407 /* HYS = 1, DSE = 111, 100k up, SPEED = HIGH */
494 /* HYS = 1, DSE = 110, 100k up, SPEED = HIGH (11)*/
524 /* HYS = 1, DSE = 110, PUE+PKE, SPEED = HIGH (11)*/
|
| D | imx6q-bosch-acc.dts | 441 connect-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; /* Old: 0, SS: HIGH */
442 intn-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; /* Old: 1, SS: HIGH */
443 reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; /* Old: 0, SS: HIGH */
|
| /Linux-v6.6/Documentation/devicetree/bindings/mfd/ |
| D | max77620.txt | 122 GPIO1/nRST_IO pins are HIGH only if all rails
123 that have POK control enabled are HIGH.
|
| D | tps6507x.txt | 30 1: If defdcdc pin of DCDC2/DCDC3 is driven HIGH.
|
| /Linux-v6.6/drivers/nfc/st95hf/ |
| D | core.c | 76 #define HIGH 1 macro
454 gpio_set_value(st95con->enable_gpio, HIGH); in st95hf_send_st95enable_negativepulse()
466 gpio_set_value(st95con->enable_gpio, HIGH); in st95hf_send_st95enable_negativepulse()
|
| /Linux-v6.6/arch/arm64/boot/dts/rockchip/ |
| D | rk3368-evb.dtsi | 224 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
|
| /Linux-v6.6/arch/arm/mach-omap1/ |
| D | board-osk.c | 223 tps65010_set_gpio_out_value(GPIO2, HIGH); in osk_tps_setup()
|
| /Linux-v6.6/Documentation/leds/ |
| D | leds-lm3556.rst | 24 or by pulling the STROBE pin HIGH.
|
| /Linux-v6.6/drivers/net/ieee802154/ |
| D | cc2520.c | 25 #define HIGH 1 macro
1109 gpiod_set_value(vreg, HIGH); in cc2520_probe()
1112 gpiod_set_value(reset, HIGH); in cc2520_probe()
|
| /Linux-v6.6/Documentation/driver-api/iio/ |
| D | buffers.rst | 62 |D11|D10|D9 |D8 |D7 |D6 |D5 |D4 | (HIGH byte, address 0x07)
|
| /Linux-v6.6/Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-max77620.txt | 66 master FPS input event set to HIGH.
|
| /Linux-v6.6/Documentation/translations/zh_CN/driver-api/gpio/ |
| D | legacy.rst | 367 HIGH: gpio_direction_input(gpio) ... 这代码关闭输出,所以上拉电阻
|
| /Linux-v6.6/tools/power/cpupower/bench/ |
| D | README-BENCH | 114 -p, --prio=<priority> scheduler priority, HIGH, LOW or DEFAULT
|
| /Linux-v6.6/Documentation/translations/zh_TW/ |
| D | gpio.txt | 371 HIGH: gpio_direction_input(gpio) ... 這代碼關閉輸出,所以上拉電阻
|
| /Linux-v6.6/arch/arm/boot/dts/renesas/ |
| D | r8a7742-iwg21d-q7-dbcm-ca.dts | 99 /* Hog GP0_18 to output HIGH to enable VIN2 */
|
