| /Linux-v4.19/drivers/media/cec/ |
| D | cec-adap.c | 350 if (data->adap->transmitting == data) { in cec_data_cancel()
351 data->adap->transmitting = NULL; in cec_data_cancel()
395 if (adap->transmitting) in cec_flush()
396 cec_data_cancel(adap->transmitting); in cec_flush()
433 if (adap->transmitting) { in cec_thread_func()
447 (!adap->transmitting && in cec_thread_func()
455 (!adap->transmitting && in cec_thread_func()
468 if (adap->transmitting && timeout) { in cec_thread_func()
478 adap->transmitting->msg.len, in cec_thread_func()
479 adap->transmitting->msg.msg); in cec_thread_func()
[all …]
|
| /Linux-v4.19/Documentation/media/uapi/rc/ |
| D | lirc-get-send-mode.rst | 31 The mode used for transmitting.
65 - Device does not support transmitting.
|
| D | lirc-get-features.rst | 52 :ref:`LIRC_MODE_PULSE <lirc-mode-pulse>` can only be used for transmitting.
|
| D | lirc-dev-intro.rst | 47 For transmitting (aka sending), create a ``struct lirc_scancode`` with
|
| /Linux-v4.19/drivers/net/team/ |
| D | Kconfig | 32 Basic mode where port used for transmitting packets is selected in
44 Basic mode where port used for transmitting packets is selected
|
| /Linux-v4.19/Documentation/devicetree/bindings/iio/health/ |
| D | afe4404.txt | 6 - tx-supply : Regulator supply to transmitting LEDs.
|
| D | afe4403.txt | 6 - tx-supply : Regulator supply to transmitting LEDs.
|
| /Linux-v4.19/drivers/media/rc/ |
| D | redrat3.c | 234 bool transmitting; member
248 if (!rr3->transmitting && (code != 0x40)) in redrat3_dump_fw_error()
286 if (!rr3->transmitting) in redrat3_dump_fw_error()
771 if (rr3->transmitting) { in redrat3_transmit_ir()
780 rr3->transmitting = true; in redrat3_transmit_ir()
857 rr3->transmitting = false; in redrat3_transmit_ir()
|
| D | ite-cir.c | 225 bool for_tx = dev->transmitting; in ite_set_carrier_params()
399 dev->transmitting = true; in ite_tx_ir()
513 dev->transmitting = false; in ite_tx_ir()
1328 wait_event_interruptible(dev->tx_ended, !dev->transmitting); in ite_close()
1650 wait_event_interruptible(dev->tx_ended, !dev->transmitting); in ite_suspend()
|
| D | ite-cir.h | 127 bool in_use, transmitting; member
|
| /Linux-v4.19/drivers/usb/class/ |
| D | cdc-acm.h | 104 int transmitting; member
|
| /Linux-v4.19/Documentation/scsi/ |
| D | cxgb3i.txt | 14 On transmitting, Chelsio S3 h/w computes and inserts the Header and
28 On transmitting, S3 h/w accepts the complete PDU (header + data)
|
| /Linux-v4.19/Documentation/devicetree/bindings/sound/ |
| D | imx-audio-spdif.txt | 15 transmitting function of S/PDIF will be enabled,
|
| /Linux-v4.19/Documentation/devicetree/bindings/media/ |
| D | st-rc.txt | 14 protocol used for transmitting remote control signals. tx-mode should
|
| /Linux-v4.19/drivers/net/hippi/ |
| D | Kconfig | 35 transmitting and receiving. This memory cannot be used by any other
|
| /Linux-v4.19/Documentation/media/uapi/cec/ |
| D | cec-pin-error-inj.rst | 89 receiving CEC messages and those relating to transmitting CEC messages. In
154 keeps transmitting after the first byte was NACKed.
186 stop transmitting ('Arbitration Lost'). This is very hard to test,
196 This setting changes the behavior of transmitting CEC messages. Normally
289 Just stop transmitting after this bit. If <op> specifies a specific CEC
|
| /Linux-v4.19/Documentation/devicetree/bindings/serial/ |
| D | atmel-usart.txt | 16 - atmel,use-dma-tx: use of PDC or DMA for transmitting data
|
| /Linux-v4.19/Documentation/devicetree/bindings/soc/fsl/cpm_qe/ |
| D | network.txt | 90 slots used for transmitting and receiving.
|
| /Linux-v4.19/Documentation/input/ |
| D | userio.rst | 61 Registers the port with the serio driver and begins transmitting data back and
|
| /Linux-v4.19/Documentation/networking/mac80211_hwsim/ |
| D | README | 35 currently enabled and on the same channel as the transmitting
|
| /Linux-v4.19/include/media/ |
| D | cec.h | 158 struct cec_data *transmitting; member
|
| /Linux-v4.19/Documentation/devicetree/bindings/display/panel/ |
| D | panel-lvds.txt | 37 below on all data lanes, transmitting bits for slots 6 to 0 instead of
|
| /Linux-v4.19/drivers/staging/most/Documentation/ |
| D | driver_usage.txt | 166 When transmitting synchronous data the allocated channel width needs to be
184 When transmitting isochronous AVP data the desired packet size needs to be
|
| /Linux-v4.19/Documentation/networking/caif/ |
| D | README | 105 might be problems transmitting over UART.
|
| /Linux-v4.19/Documentation/serial/ |
| D | driver | 116 Stop transmitting characters. This might be due to the CTS
120 The driver should stop transmitting characters as soon as
128 Start transmitting characters.
|
