Home
last modified time | relevance | path

Searched +full:resistance +full:- +full:temp +full:- +full:table (Results 1 – 13 of 13) sorted by relevance

/Linux-v5.15/drivers/power/supply/
Dab8500-bm.h1 /* SPDX-License-Identifier: GPL-2.0-only */
283 * struct ab8500_res_to_temp - defines one point in a temp to res curve. To
286 * @temp: battery pack temperature in Celsius
287 * @resist: NTC resistor net total resistance
290 int temp; member
295 * struct ab8500_v_to_cap - Table for translating voltage to capacity
308 * struct ab8500_fg_parameters - Fuel gauge algorithm parameters, in seconds
360 * struct ab8500_charger_maximization - struct used by the board config.
374 * struct ab8500_battery_type - different batteries supported
376 * @resis_high: battery upper resistance limit
[all …]
Dpower_supply_core.c1 // SPDX-License-Identifier: GPL-2.0-only
42 if (!supply->supplied_from && !supplier->supplied_to) in __power_supply_is_supplied_by()
46 if (supply->supplied_from) { in __power_supply_is_supplied_by()
47 if (!supplier->desc->name) in __power_supply_is_supplied_by()
49 for (i = 0; i < supply->num_supplies; i++) in __power_supply_is_supplied_by()
50 if (!strcmp(supplier->desc->name, supply->supplied_from[i])) in __power_supply_is_supplied_by()
53 if (!supply->desc->name) in __power_supply_is_supplied_by()
55 for (i = 0; i < supplier->num_supplicants; i++) in __power_supply_is_supplied_by()
56 if (!strcmp(supplier->supplied_to[i], supply->desc->name)) in __power_supply_is_supplied_by()
69 if (pst->desc->external_power_changed) in __power_supply_changed_work()
[all …]
Dsc27xx_fuel_gauge.c1 // SPDX-License-Identifier: GPL-2.0
10 #include <linux/nvmem-consumer.h>
81 * @internal_resist: the battery internal resistance in mOhm
89 * @table_len: the capacity table length
90 * @resist_table_len: the resistance table length
93 * @calib_resist: the real resistance of coulomb counter chip in uOhm
94 * @cap_table: capacity table with corresponding ocv
95 * @resist_table: resistance percent table with corresponding temperature
128 static int sc27xx_fgu_get_temp(struct sc27xx_fgu_data *data, int *temp);
139 return DIV_S64_ROUND_CLOSEST(adc * 1000, data->cur_1000ma_adc); in sc27xx_fgu_adc_to_current()
[all …]
Dab8500_btemp.c1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) ST-Ericsson SA 2012
30 #include <linux/fixp-arith.h>
32 #include "ab8500-bm.h"
36 #define BTEMP_THERMAL_LOW_LIMIT -10
52 * struct ab8500_btemp_interrupts - ab8500 interrupts
78 * struct ab8500_btemp - ab8500 BTEMP device information
126 * ab8500_btemp_batctrl_volt_to_res() - convert batctrl voltage to resistance
131 * This function returns the battery resistance that is
140 if (is_ab8500_1p1_or_earlier(di->parent)) { in ab8500_btemp_batctrl_volt_to_res()
[all …]
/Linux-v5.15/Documentation/devicetree/bindings/power/supply/
Dbattery.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Sebastian Reichel <sre@kernel.org>
14 In smart batteries, these are typically stored in non-volatile memory
16 no appropriate non-volatile memory, or it is unprogrammed/incorrect.
27 Batteries must be referenced by chargers and/or fuel-gauges using a phandle.
28 The phandle's property should be named "monitored-battery".
32 const: simple-battery
34 device-chemistry:
[all …]
Dsc27xx-fg.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: "http://devicetree.org/schemas/power/supply/sc27xx-fg.yaml#"
5 $schema: "http://devicetree.org/meta-schemas/core.yaml#"
10 - Sebastian Reichel <sre@kernel.org>
13 - $ref: power-supply.yaml#
18 - sprd,sc2720-fgu
19 - sprd,sc2721-fgu
20 - sprd,sc2723-fgu
21 - sprd,sc2730-fgu
[all …]
/Linux-v5.15/drivers/iio/adc/
Dqcom-vadc-common.c1 // SPDX-License-Identifier: GPL-2.0
5 #include <linux/fixp-arith.h>
6 #include <linux/iio/adc/qcom-vadc-common.h>
14 * struct vadc_map_pt - Map the graph representation for ADC channel
17 * resistance.
26 {1758, -40000 },
27 {1742, -35000 },
28 {1719, -30000 },
29 {1691, -25000 },
30 {1654, -20000 },
[all …]
Dtwl4030-madc.c1 // SPDX-License-Identifier: GPL-2.0-only
4 * TWL4030 MADC module driver-This driver monitors the real time
8 * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
9 * J Keerthy <j-keerthy@ti.com>
11 * Based on twl4030-madc.c
118 * struct twl4030_madc_request - madc request packet for channel conversion
153 * struct twl4030_madc_data - a container for madc info
158 * @use_second_irq: IRQ selection (main or co-processor)
182 req.method = madc->use_second_irq ? TWL4030_MADC_SW2 : TWL4030_MADC_SW1; in twl4030_madc_read()
184 req.channels = BIT(chan->channel); in twl4030_madc_read()
[all …]
Dab8500-gpadc.c1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) ST-Ericsson SA 2010
15 * detection by resistance measurements using relative voltages and GSM burst
54 /* 0 = use VTVOUT, 1 = use VRTC as pull-up supply for battery temp NTC */
63 * the bit layout is the same for SW and HW conversion set-up
163 #define AB8500_ADC_CH_IBAT_MIN (-6000) /* mA range measured by ADC for ibat */
165 #define AB8500_ADC_CH_IBAT_MIN_V (-60) /* mV range measured by ADC for ibat */
167 #define AB8500_GPADC_IBAT_VDROP_L (-56) /* mV */
192 * struct ab8500_adc_cal_data - Table for storing gain and offset for the
207 * struct ab8500_gpadc_chan_info - per-channel GPADC info
[all …]
/Linux-v5.15/include/linux/
Dpower_supply.h1 /* SPDX-License-Identifier: GPL-2.0-only */
217 /* Run-time specific power supply configuration */
339 int temp; /* celsius */ member
340 int resistance; /* internal resistance percent */ member
350 * The default field value is -EINVAL.
356 int energy_full_design_uwh; /* microWatt-hours */
357 int charge_full_design_uah; /* microAmp-hours */
411 extern int power_supply_ocv2cap_simple(struct power_supply_battery_ocv_table *table,
415 int temp, int *table_len);
417 int ocv, int temp);
[all …]
/Linux-v5.15/drivers/hwmon/
Dntc_thermistor.c1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * ntc_thermistor.c - NTC Thermistors
16 #include <linux/fixp-arith.h>
30 * Used as index in a zero-terminated array, holes not allowed so
60 * A compensation table should be sorted by the values of .ohm
66 { .temp_c = -40, .ohm = 1747920 },
67 { .temp_c = -35, .ohm = 1245428 },
68 { .temp_c = -30, .ohm = 898485 },
69 { .temp_c = -25, .ohm = 655802 },
70 { .temp_c = -20, .ohm = 483954 },
[all …]
/Linux-v5.15/Documentation/hwmon/
Dvt1211.rst10 Addresses scanned: none, address read from Super-I/O config space
24 -----------------
29 configuration for channels 1-5.
30 Legal values are in the range of 0-31. Bit 0 maps to
47 -----------
49 The VIA VT1211 Super-I/O chip includes complete hardware monitoring
52 implements 5 universal input channels (UCH1-5) that can be individually
60 connected to the PWM outputs of the VT1211 :-().
62 The following table shows the relationship between the vt1211 inputs and the
66 Sensor Voltage Mode Temp Mode Default Use (from the datasheet)
[all …]
/Linux-v5.15/drivers/iio/chemical/
Dbme680_core.c1 // SPDX-License-Identifier: GPL-2.0
3 * Bosch BME680 - Temperature, Pressure, Humidity & Gas Sensor
5 * Copyright (C) 2017 - 2018 Bosch Sensortec GmbH
9 * https://ae-bst.resource.bosch.com/media/_tech/media/datasheets/BST-BME680-DS001-00.pdf
111 struct device *dev = regmap_get_device(data->regmap); in bme680_read_calib()
117 ret = regmap_bulk_read(data->regmap, BME680_T1_LSB_REG, in bme680_read_calib()
123 calib->par_t1 = le16_to_cpu(buf); in bme680_read_calib()
125 ret = regmap_bulk_read(data->regmap, BME680_T2_LSB_REG, in bme680_read_calib()
131 calib->par_t2 = le16_to_cpu(buf); in bme680_read_calib()
133 ret = regmap_read(data->regmap, BME680_T3_REG, &tmp); in bme680_read_calib()
[all …]