Searched full:reconfigure (Results 1 – 25 of 315) sorted by relevance
12345678910>>...13
| /Linux-v6.6/include/linux/phy/ |
| D | phy-dp.h | 69 * Flag indicating, whether or not reconfigure link rate and SSC to
78 * Flag indicating, whether or not reconfigure lane count to
87 * Flag indicating, whether or not reconfigure voltage swing
|
| /Linux-v6.6/drivers/net/ethernet/netronome/nfp/ |
| D | nfp_net_common.c | 183 * @nn: NFP Net device to reconfigure
251 * __nfp_net_reconfig() - Reconfigure the firmware
252 * @nn: NFP Net device to reconfigure
306 * nfp_net_mbox_reconfig() - Reconfigure the firmware via the mailbox
307 * @nn: NFP Net device to reconfigure
851 * @nn: NFP Net device to reconfigure
864 * @nn: NFP Net device to reconfigure
877 * @nn: NFP Net device to reconfigure
906 * @nn: NFP Net device to reconfigure
921 * @nn: NFP Net device to reconfigure
[all …]
|
| /Linux-v6.6/fs/autofs/ |
| D | Kconfig | 18 don't have a laptop which needs to dynamically reconfigure to the
|
| /Linux-v6.6/drivers/nvdimm/ |
| D | pfn.h | 36 * configurations mainly to allow a backup, reconfigure the
|
| /Linux-v6.6/Documentation/devicetree/bindings/power/reset/ |
| D | gpio-poweroff.yaml | 31 Initially configure the GPIO line as an input. Only reconfigure
|
| /Linux-v6.6/drivers/net/ethernet/microchip/sparx5/ |
| D | sparx5_psfp.c | 235 /* Was already in use, no need to reconfigure */ in sparx5_psfp_sg_add()
276 /* Was already in use, no need to reconfigure */ in sparx5_psfp_fm_add()
|
| /Linux-v6.6/include/net/ |
| D | ncsi.h | 15 * package and channel while ncsi_dev_state_config helps to reconfigure
|
| /Linux-v6.6/fs/jfs/ |
| D | resize.c | 116 * reconfigure LV spaces in jfs_extendfs()
123 * reconfigure inline log space: in jfs_extendfs()
152 * reconfigure fsck work space: in jfs_extendfs()
|
| /Linux-v6.6/Documentation/userspace-api/media/mediactl/ |
| D | request-api.rst | 12 the same pipeline to reconfigure and collaborate closely on a per-frame basis.
21 on the media pipeline, reconfigure it for the next frame, queue the buffers to
|
| /Linux-v6.6/arch/mips/bcm63xx/ |
| D | prom.c | 85 * reconfigure itself then go back to sleep. in prom_init()
|
| /Linux-v6.6/Documentation/networking/device_drivers/atm/ |
| D | fore200e.rst | 56 2. Reconfigure your kernel to set the new firmware name and location.
|
| /Linux-v6.6/Documentation/ABI/testing/ |
| D | debugfs-driver-dcc | 25 reconfigure addresses again.
|
| /Linux-v6.6/drivers/net/ethernet/sfc/falcon/ |
| D | mdio_10g.h | 75 /* Generic part of reconfigure: set/clear loopback bits */
|
| D | tenxpress.c | 241 /* Try and reconfigure the device */ in tenxpress_special_reset()
481 .reconfigure = tenxpress_phy_reconfigure,
|
| /Linux-v6.6/fs/vboxsf/ |
| D | super.c | 69 vbg_err("vboxsf: Cannot reconfigure nls option\n"); in vboxsf_parse_param()
431 .reconfigure = vboxsf_reconfigure,
|
| /Linux-v6.6/Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-bindings.txt | 15 need to reconfigure pins at run-time, for example to tri-state pins when the
|
| /Linux-v6.6/fs/ |
| D | fs_context.c | 695 .reconfigure = legacy_reconfigure,
724 * from where it can be used to reconfigure a superblock.
733 * until we actually try to reconfigure.
|
| /Linux-v6.6/Documentation/userspace-api/media/v4l/ |
| D | vidioc-subdev-g-routing.rst | 50 means that the userspace must reconfigure all streams after calling the ioctl
|
| /Linux-v6.6/Documentation/devicetree/bindings/mmc/ |
| D | ti-omap-hsmmc.txt | 104 The workaround is to reconfigure the dat1 line as a GPIO upon suspend. To make
|
| /Linux-v6.6/Documentation/driver-api/usb/ |
| D | typec_bus.rst | 52 in need to reconfigure the pins on the connector, the alternate mode driver
|
| /Linux-v6.6/drivers/crypto/intel/qat/qat_common/ |
| D | adf_sysfs.c | 133 dev_info(dev, "Device qat_dev%d must be down to reconfigure the service.\n", in cfg_services_store()
|
| /Linux-v6.6/drivers/net/ethernet/stmicro/stmmac/ |
| D | dwmac-sunxi.c | 79 /* only GMII mode requires us to reconfigure the clock lines */ in sun7i_fix_speed()
|
| /Linux-v6.6/drivers/pwm/ |
| D | pwm-renesas-tpu.c | 160 * Make sure the channel is stopped, as we need to reconfigure it in tpu_pwm_timer_start()
328 * running, there's no need to reconfigure it completely, Just in tpu_pwm_config()
|
| /Linux-v6.6/Documentation/networking/device_drivers/ethernet/cirrus/ |
| D | cs89x0.rst | 459 option to reconfigure the adapter by selecting a different value for the system
536 self-test. If so, reconfigure the adapter selecting another choice for the
541 the adapter and reconfigure it by installing it in another PC to run the
|
| /Linux-v6.6/Documentation/devicetree/bindings/pci/ |
| D | host-generic-pci.yaml | 72 is there any reason for the driver to reconfigure ATU windows for
|
12345678910>>...13
