| /Linux-v6.6/drivers/leds/ |
| D | leds-lt3593.c | 26 int pulses; in lt3593_led_set() local
42 pulses = 32 - (value * 32) / 255; in lt3593_led_set()
44 if (pulses == 0) { in lt3593_led_set()
53 while (pulses--) { in lt3593_led_set()
|
| /Linux-v6.6/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-timer-stm32 | 37 OC4REF rising or falling edges generate pulses.
39 OC6REF rising or falling edges generate pulses.
41 OC4REF or OC6REF rising edges generate pulses.
44 pulses.
46 OC5REF or OC6REF rising edges generate pulses.
49 pulses.
|
| D | sysfs-bus-counter | 119 by two on succeeding clock pulses. When the count
126 two on succeeding clock pulses. One clock pulse after
129 Succeeding clock pulses decrement the count by two. When
334 attribute indicates the value in nanoseconds where noise pulses
|
| D | sysfs-class-hwmon | 230 Number of tachometer pulses per fan revolution.
241 the number of pulses. In the absence of such a register (and
242 thus attribute) the value assumed by all devices is 2 pulses
|
| /Linux-v6.6/Documentation/input/devices/ |
| D | walkera0701.rst | 20 pulses from processor to HF part can be found at pin 2 of this connector,
22 modulation pulses to PC, signal pulses must be amplified.
62 Signal pulses
98 (Warning, pulses on ACK are inverted by transistor, irq is raised up on sync
105 values can be sampled between sync pulses.
|
| /Linux-v6.6/drivers/hwmon/ |
| D | pwm-fan.c | 26 atomic_t pulses; member
69 atomic_inc(&tach->pulses); in pulse_handler()
83 int pulses; in sample_timer() local
85 pulses = atomic_read(&tach->pulses); in sample_timer()
86 atomic_sub(pulses, &tach->pulses); in sample_timer()
87 tach->rpm = (unsigned int)(pulses * 1000 * 60) / in sample_timer()
|
| /Linux-v6.6/drivers/net/wireless/ath/ |
| D | dfs_pri_detector.c | 162 struct list_head *l = &pde->pulses; in pulse_queue_get_tail()
215 list_add(&p->head, &pde->pulses); in pulse_queue_enqueue()
228 list_for_each_entry(p, &pde->pulses, head) { in pseq_handler_create_sequences()
257 list_for_each_entry_continue(p2, &pde->pulses, head) { in pseq_handler_create_sequences()
366 list_for_each_entry_safe(p, p0, &pde->pulses, head) { in pri_detector_reset()
429 INIT_LIST_HEAD(&de->pulses); in pri_detector_init()
|
| D | dfs_pri_detector.h | 70 struct list_head pulses; member
|
| /Linux-v6.6/Documentation/hwmon/ |
| D | g762.rst | 18 hardware characteristics of the system (reference clock, pulses per
36 number of pulses per fan revolution. Supported values
71 system: a reference clock source frequency, a number of pulses per fan
|
| D | sl28cpld.rst | 35 fan1_input Fan RPM. Assuming 2 pulses per revolution.
|
| D | aquacomputer_d5next.rst | 52 voltage and current. Flow sensor pulses are also available.
95 fan5_pulses Quadro flow sensor pulses
|
| D | g760a.rst | 23 consecutive speed pulses. The period is defined in terms of clock
|
| D | nsa320.rst | 55 is reduced from 100 us to less than 15 us then data pulses are likely to be
|
| D | dme1737.rst | 163 to the number of pulses per fan revolution that the connected tachometer
165 that generate 2 pulses per revolution. Fan inputs 5-6 also provide a max
296 number of pulses per revolution that
|
| D | smsc47b397.rst | 90 The SIO counts the number of 90kHz (11.111us) pulses per revolution.
|
| /Linux-v6.6/arch/arm/boot/dts/aspeed/ |
| D | aspeed-bmc-opp-swift.dts | 349 tach-pulses = <2>;
361 tach-pulses = <2>;
373 tach-pulses = <2>;
385 tach-pulses = <2>;
397 tach-pulses = <2>;
|
| D | aspeed-bmc-opp-tacoma.dts | 486 tach-pulses = <2>;
499 tach-pulses = <2>;
512 tach-pulses = <2>;
525 tach-pulses = <2>;
|
| D | aspeed-bmc-ibm-rainier.dts | 1085 tach-pulses = <2>;
1091 tach-pulses = <2>;
1097 tach-pulses = <2>;
1103 tach-pulses = <2>;
1109 tach-pulses = <2>;
1115 tach-pulses = <2>;
|
| D | aspeed-bmc-ibm-bonnell.dts | 277 tach-pulses = <2>;
283 tach-pulses = <2>;
|
| /Linux-v6.6/Documentation/userspace-api/media/rc/ |
| D | lirc-set-send-carrier.rst | 34 Set send carrier used to modulate IR PWM pulses and spaces.
|
| D | lirc-set-rec-carrier.rst | 34 Set receive carrier used to modulate IR PWM pulses and spaces.
|
| /Linux-v6.6/Documentation/i2c/ |
| D | gpio-fault-injection.rst | 81 register 0x00 (if it has registers) when further clock pulses happen on SCL.
82 This is why bus recovery (up to 9 clock pulses) must either check SDA or send
|
| /Linux-v6.6/Documentation/driver-api/ |
| D | reset.rst | 42 carefully timed sequence of pulses on multiple reset lines.
61 trigger reset pulses, or to query reset line status.
|
| /Linux-v6.6/drivers/leds/trigger/ |
| D | Kconfig | 25 This allows LEDs to blink in one-shot pulses with parameters
|
| /Linux-v6.6/drivers/gpu/drm/i915/ |
| D | Kconfig.profile | 42 int "Interval between heartbeat pulses (ms)"
|
