Searched refs:ohm (Results 1 – 25 of 49) sorted by relevance
12
| /Linux-v6.6/drivers/hwmon/ |
| D | ntc_thermistor.c | 31 unsigned int ohm; member
73 { .temp_c = -40, .ohm = 1747920 },
74 { .temp_c = -35, .ohm = 1245428 },
75 { .temp_c = -30, .ohm = 898485 },
76 { .temp_c = -25, .ohm = 655802 },
77 { .temp_c = -20, .ohm = 483954 },
78 { .temp_c = -15, .ohm = 360850 },
79 { .temp_c = -10, .ohm = 271697 },
80 { .temp_c = -5, .ohm = 206463 },
81 { .temp_c = 0, .ohm = 158214 },
[all …]
|
| /Linux-v6.6/arch/arm/boot/dts/ |
| D | cros-adc-thermistors.dtsi | 16 pullup-ohm = <47000>;
17 pulldown-ohm = <0>;
23 pullup-ohm = <47000>;
24 pulldown-ohm = <0>;
30 pullup-ohm = <47000>;
31 pulldown-ohm = <0>;
37 pullup-ohm = <47000>;
38 pulldown-ohm = <0>;
|
| /Linux-v6.6/drivers/iio/potentiometer/ |
| D | max5432.c | 28 unsigned long ohm; member
52 if (unlikely(data->ohm > INT_MAX)) in max5432_read_raw()
55 *val = data->ohm; in max5432_read_raw()
102 data->ohm = (unsigned long)device_get_match_data(dev); in max5432_probe()
|
| /Linux-v6.6/Documentation/devicetree/bindings/phy/ |
| D | rockchip-emmc-phy.txt | 16 - drive-impedance-ohm: Specifies the drive impedance in Ohm.
40 drive-impedance-ohm = <50>;
|
| /Linux-v6.6/arch/arm64/boot/dts/rockchip/ |
| D | rk3399-gru-kevin.dts | 71 pullup-ohm = <25500>;
72 pulldown-ohm = <0>;
80 pullup-ohm = <25500>;
81 pulldown-ohm = <0>;
|
| /Linux-v6.6/arch/arm/boot/dts/st/ |
| D | ste-hrefv60plus.dtsi | 57 pullup-ohm = <220000>;
58 pulldown-ohm = <0>;
66 pullup-ohm = <220000>;
67 pulldown-ohm = <0>;
|
| D | ste-href.dtsi | 42 pullup-ohm = <230000>;
43 pulldown-ohm = <0>;
|
| D | ste-snowball.dts | 46 pullup-ohm = <230000>;
47 pulldown-ohm = <0>;
|
| D | ste-ux500-samsung-golden.dts | 53 pullup-ohm = <230000>;
54 pulldown-ohm = <0>;
|
| /Linux-v6.6/arch/arm64/boot/dts/ti/ |
| D | k3-am62-verdin-wifi.dtsi | 29 ti,driver-strength-ohm = <50>;
|
| D | k3-am6548-iot2050-advanced-common.dtsi | 50 ti,driver-strength-ohm = <50>;
|
| D | k3-j7200-common-proc-board.dts | 320 ti,driver-strength-ohm = <50>;
331 ti,driver-strength-ohm = <50>;
|
| D | k3-am62-verdin-dahlia.dtsi | 188 ti,driver-strength-ohm = <33>;
|
| D | k3-am62-verdin-dev.dtsi | 209 ti,driver-strength-ohm = <33>;
|
| D | k3-am642-tqma64xxl.dtsi | 214 ti,driver-strength-ohm = <50>;
|
| D | k3-am62x-sk-common.dtsi | 396 ti,driver-strength-ohm = <50>;
405 ti,driver-strength-ohm = <50>;
|
| D | k3-am64-phycore-som.dtsi | 205 ti,driver-strength-ohm = <50>;
|
| D | k3-am642-sk.dts | 432 ti,driver-strength-ohm = <50>;
452 ti,driver-strength-ohm = <50>;
|
| D | k3-am654-base-board.dts | 449 ti,driver-strength-ohm = <50>;
462 ti,driver-strength-ohm = <50>;
|
| /Linux-v6.6/arch/arm64/boot/dts/mediatek/ |
| D | mt8183-pumpkin.dts | 62 pullup-ohm = <390000>;
63 pulldown-ohm = <0>;
|
| D | mt8183-evb.dts | 44 pullup-ohm = <390000>;
45 pulldown-ohm = <0>;
|
| /Linux-v6.6/arch/arm/boot/dts/samsung/ |
| D | exynos3250-monk.dts | 148 pullup-ohm = <100000>;
149 pulldown-ohm = <100000>;
156 pullup-ohm = <100000>;
157 pulldown-ohm = <100000>;
|
| D | exynos3250-rinato.dts | 150 pullup-ohm = <100000>;
151 pulldown-ohm = <100000>;
158 pullup-ohm = <100000>;
159 pulldown-ohm = <100000>;
|
| /Linux-v6.6/arch/arm64/boot/dts/exynos/ |
| D | exynos5433-tm2-common.dtsi | 150 pullup-ohm = <100000>;
151 pulldown-ohm = <0>;
158 pullup-ohm = <100000>;
159 pulldown-ohm = <0>;
167 pullup-ohm = <100000>;
168 pulldown-ohm = <0>;
|
| /Linux-v6.6/Documentation/admin-guide/auxdisplay/ |
| D | cfag12864b.rst | 75 Ground (21)---[GND] [GND]---[P1]---(18) Vee - R = Resistor = 22 ohm
|
12
