Home
last modified time | relevance | path

Searched refs:degrees (Results 1 – 25 of 121) sorted by relevance

12345

/Linux-v6.6/include/linux/
Dfixp-arith.h49 static inline s32 __fixp_sin32(int degrees) in __fixp_sin32() argument
54 if (degrees > 180) { in __fixp_sin32()
56 degrees -= 180; in __fixp_sin32()
58 if (degrees > 90) in __fixp_sin32()
59 degrees = 180 - degrees; in __fixp_sin32()
61 ret = sin_table[degrees]; in __fixp_sin32()
73 static inline s32 fixp_sin32(int degrees) in fixp_sin32() argument
75 degrees = (degrees % 360 + 360) % 360; in fixp_sin32()
77 return __fixp_sin32(degrees); in fixp_sin32()
115 int degrees; in fixp_sin32_rad() local
[all …]
/Linux-v6.6/drivers/clk/rockchip/
Dclk-mmc-phase.c51 u16 degrees; in rockchip_mmc_get_phase() local
60 degrees = (raw_value & ROCKCHIP_MMC_DEGREE_MASK) * 90; in rockchip_mmc_get_phase()
69 degrees += DIV_ROUND_CLOSEST(delay_num * factor, 1000000); in rockchip_mmc_get_phase()
72 return degrees % 360; in rockchip_mmc_get_phase()
75 static int rockchip_mmc_set_phase(struct clk_hw *hw, int degrees) in rockchip_mmc_set_phase() argument
101 nineties = degrees / 90; in rockchip_mmc_set_phase()
102 remainder = (degrees % 90); in rockchip_mmc_set_phase()
142 clk_hw_get_name(hw), degrees, delay_num, in rockchip_mmc_set_phase()
Dclk-inverter.c35 static int rockchip_inv_set_phase(struct clk_hw *hw, int degrees) in rockchip_inv_set_phase() argument
40 if (degrees % 180 == 0) { in rockchip_inv_set_phase()
41 val = !!degrees; in rockchip_inv_set_phase()
44 __func__, degrees, clk_hw_get_name(hw)); in rockchip_inv_set_phase()
/Linux-v6.6/drivers/clk/meson/
Dclk-phase.c26 static unsigned int meson_clk_degrees_to_val(int degrees, unsigned int width) in meson_clk_degrees_to_val() argument
28 unsigned int val = DIV_ROUND_CLOSEST(degrees, phase_step(width)); in meson_clk_degrees_to_val()
48 static int meson_clk_phase_set_phase(struct clk_hw *hw, int degrees) in meson_clk_phase_set_phase() argument
54 val = meson_clk_degrees_to_val(degrees, phase->ph.width); in meson_clk_phase_set_phase()
107 static int meson_clk_triphase_set_phase(struct clk_hw *hw, int degrees) in meson_clk_triphase_set_phase() argument
113 val = meson_clk_degrees_to_val(degrees, tph->ph0.width); in meson_clk_triphase_set_phase()
164 static int meson_sclk_ws_inv_set_phase(struct clk_hw *hw, int degrees) in meson_sclk_ws_inv_set_phase() argument
170 val = meson_clk_degrees_to_val(degrees, tph->ph.width); in meson_sclk_ws_inv_set_phase()
/Linux-v6.6/drivers/mmc/host/
Ddw_mmc-hi3798cv200.c63 static const int degrees[] = { 0, 45, 90, 135, 180, 225, 270, 315 }; in dw_mci_hi3798cv200_execute_tuning() local
71 for (i = 0; i < ARRAY_SIZE(degrees); i++) { in dw_mci_hi3798cv200_execute_tuning()
72 clk_set_phase(priv->sample_clk, degrees[i]); in dw_mci_hi3798cv200_execute_tuning()
98 fall_point = ARRAY_SIZE(degrees) - 1; in dw_mci_hi3798cv200_execute_tuning()
101 (ARRAY_SIZE(degrees) - 1)) in dw_mci_hi3798cv200_execute_tuning()
104 i = (raise_point + ARRAY_SIZE(degrees) - 1) / 2; in dw_mci_hi3798cv200_execute_tuning()
109 clk_set_phase(priv->sample_clk, degrees[i]); in dw_mci_hi3798cv200_execute_tuning()
111 raise_point, fall_point, degrees[i]); in dw_mci_hi3798cv200_execute_tuning()
/Linux-v6.6/Documentation/hwmon/
Dds1621.rst68 Fahrenheit range of -67 to +257 degrees with 0.9 steps. If polarity
81 of up to +/- 0.5 degrees even when compared against precise temperature
107 and 80 degrees respectively).
125 - DS1621: +/- 0.5 degree Celsius (from 0 to +70 degrees)
126 - DS1625: +/- 0.5 degree Celsius (from 0 to +70 degrees)
127 - DS1631: +/- 0.5 degree Celsius (from 0 to +70 degrees)
128 - DS1721: +/- 1.0 degree Celsius (from -10 to +85 degrees)
129 - DS1731: +/- 1.0 degree Celsius (from -10 to +85 degrees)
146 0 0 9 bits, 0.5 degrees Celsius
147 1 0 10 bits, 0.25 degrees Celsius
[all …]
Dlm77.rst37 was 80 degrees C, and the hysteresis was 75 degrees C, and you change
38 the critical limit to 90 degrees C, then the hysteresis will
39 automatically change to 85 degrees C.
Dw83773g.rst26 Temperature is measured in degrees Celsius.
28 range of -40 to +125 degrees Celsius (for local sensor) and -40 to +127
29 degrees Celsius (for remote sensors).
Dk8temp.rst42 Temperatures are measured in degrees Celsius and measurement resolution is
45 206 degrees C.
61 70 degrees C. The rule of the thumb -> CPU temperature should not cross
62 60 degrees C too much.
Demc1403.rst72 was 80 degrees C, and the hysteresis was 75 degrees C, and you change
73 the critical limit to 90 degrees C, then the hysteresis will
74 automatically change to 85 degrees C.
Dtmp513.rst34 The temperatures are measured in degrees Celsius with a range of
35 -40 to + 125 degrees with a resolution of 0.0625 degree C.
39 hysteresis value. The hysteresis is in degrees Celsius with a range of
40 0 to 127.5 degrees with a resolution of 0.5 degree.
Dad7314.rst28 sensor with 1lsb = 0.25 degrees centigrade. The adt7301 and
29 adt7302 have 14 bit sensors with 1lsb = 0.03125 degrees centigrade.
Dw83l785ts.rst24 theoretically defined as 85 or 100 degrees C through a combination
27 degrees C. The datasheet is rather poor and obviously inaccurate
30 All temperature values are given in degrees Celsius. Resolution
Dlm70.rst56 13-bit temperature data (0.0625 degrees celsius resolution).
61 with 0.25 degrees Celsius resolution.
64 data (0.03125 degrees celsius resolution).
Dhs3001.rst24 and temperature family. Temperature is measured in degrees celsius, relative
26 scaled by 1000, i.e. the value for 31.5 degrees celsius is 31500.
Dadc128d818.rst24 Temperatures are measured in degrees Celsius. There is one set of limits.
27 Measurements are guaranteed between -55 and +125 degrees. The temperature
28 measurement has a resolution of 0.5 degrees; the limits have a resolution
Dlan966x.rst24 of the sensor is specified from -40 to +125 degrees Celsius and
25 its accuracy is +/- 5 degrees Celsius. The fan controller has a
Dgl518sm.rst43 Temperatures are measured in degrees Celsius. An alarm goes off while the
46 situation. Measurements are guaranteed between -10 degrees and +110
47 degrees, with a accuracy of +/-3 degrees.
Dlm73.rst26 given in degrees Celsius.
31 The LM73 supports four resolutions, defined in terms of degrees C per
87 resolution in degrees C per LSB.
Dlm83.rst85 All temperature values are given in degrees Celsius. Local temperature
86 is given within a range of 0 to +85 degrees. Remote temperatures are
87 given within a range of 0 to +125 degrees. Resolution is 1.0 degree,
88 accuracy is guaranteed to 3.0 degrees (see the datasheet for more
Dmax31827.rst52 hysteresis value: -40 and -30 degrees for under temperature alarm and +100 and
53 +90 degrees for over temperature alarm.
79 The LSB of the temperature values is 0.0625 degrees Celsius, but the values of
80 the temperatures are displayed in milli-degrees. This means, that some data is
/Linux-v6.6/drivers/clk/hisilicon/
Dclk-hisi-phase.c54 int degrees) in hisi_phase_degrees_to_regval() argument
59 if (phase->phase_degrees[i] == degrees) in hisi_phase_degrees_to_regval()
65 static int hisi_clk_set_phase(struct clk_hw *hw, int degrees) in hisi_clk_set_phase() argument
72 regval = hisi_phase_degrees_to_regval(phase, degrees); in hisi_clk_set_phase()
/Linux-v6.6/drivers/clk/sunxi-ng/
Dccu_phase.c56 static int ccu_phase_set_phase(struct clk_hw *hw, int degrees) in ccu_phase_set_phase() argument
85 if (degrees != 180) { in ccu_phase_set_phase()
105 delay = DIV_ROUND_CLOSEST(degrees, step); in ccu_phase_set_phase()
/Linux-v6.6/drivers/gpu/drm/nouveau/dispnv04/
Doverlay.c75 sin_mul(int degrees, int factor) in sin_mul() argument
77 if (degrees > 180) { in sin_mul()
78 degrees -= 180; in sin_mul()
81 return factor * 4 * degrees * (180 - degrees) / in sin_mul()
82 (40500 - degrees * (180 - degrees)); in sin_mul()
87 cos_mul(int degrees, int factor) in cos_mul() argument
89 return sin_mul((degrees + 90) % 360, factor); in cos_mul()
/Linux-v6.6/drivers/hwmon/
Demc2103.c51 s8 degrees; member
88 u8 degrees, fractional; in read_temp_from_i2c() local
90 if (read_u8_from_i2c(client, i2c_reg, &degrees) < 0) in read_temp_from_i2c()
96 temp->degrees = degrees; in read_temp_from_i2c()
179 int millidegrees = data->temp[nr].degrees * 1000 in temp_show()
207 bool fault = (data->temp[nr].degrees == -128); in temp_fault_show()

12345