| /Linux-v6.6/Documentation/leds/ |
| D | leds-cht-wcove.rst | 35 This is just like how blinking works in the LED subsystem,
36 for both sw and hw blinking the brightness can also be changed
37 while blinking. Breathing on this hw really is just a variant
38 mode of blinking.
|
| D | ledtrig-oneshot.rst | 13 event, while in the latter it keeps blinking at constant rate, as to signal
40 echo 1 > shot # led starts blinking, ignored if already blinking
|
| D | leds-lp55xx.rst | 90 For example, run blinking pattern in engine #1 of LP5521::
98 For example, run blinking pattern in engine #3 of LP55231
109 To start blinking patterns in engine #2 and #3 simultaneously::
192 /* mode_1: blinking data */
219 echo 1 > /sys/bus/i2c/devices/xxxx/led_pattern # red blinking LED pattern
|
| D | leds-class.rst | 126 blinking,
132 blinking, returns -EBUSY if software blink fallback is enabled.
155 blink_set() function (see <linux/leds.h>). To set an LED to blinking,
159 To turn off blinking, use the API function led_brightness_set()
161 timers that may have been required for blinking.
163 The blink_set() function should choose a user friendly blinking value
170 hardware blinking function, if any.
229 device for the trigger as the source for blinking
|
| D | leds-lp5562.rst | 49 For example, run blinking green channel pattern::
58 To run a blinking white pattern::
|
| D | leds-blinkm.rst | 13 Also you can store blinking sequences as "scripts" in
|
| D | leds-mlxcpld.rst | 117 Driver supports HW blinking at 3Hz and 6Hz frequency (50% duty cycle).
|
| /Linux-v6.6/Documentation/admin-guide/ |
| D | vga-softcursor.rst | 9 tricks: you can make your cursor look like a non-blinking red block,
40 on highlight (or sometimes blinking -- it depends on the configuration
52 To get normal blinking underline, use::
56 To get blinking block, use::
60 To get red non-blinking block, use::
|
| /Linux-v6.6/drivers/leds/ |
| D | leds-pca963x.c | 104 bool blinking; member
133 if (led->blinking) { in pca963x_brightness()
147 led->blinking = false; in pca963x_brightness()
157 if (led->blinking) in pca963x_brightness()
198 led->blinking = true; in pca963x_blink()
357 led->blinking = false; in pca963x_register_leds()
|
| D | leds-gpio.c | 26 u8 blinking; member
47 if (led_dat->blinking) { in gpio_led_set()
50 led_dat->blinking = 0; in gpio_led_set()
71 led_dat->blinking = 1; in gpio_blink_set()
90 led_dat->blinking = 0; in create_gpio_led()
|
| D | leds-ss4200.c | 448 int blinking = 0; in blink_show() local
450 blinking = 1; in blink_show()
451 return sprintf(buf, "%u\n", blinking); in blink_show()
|
| D | leds-lm355x.c | 118 u8 blinking; member
369 indicator_pattern[state].blinking); in pattern_store()
|
| D | Kconfig | 226 hardware-accelerated blinking with maximum on and off periods of 9.8
618 can stop the front LED from blinking after startup.
679 Driver support brightness control and hardware-assisted blinking.
|
| /Linux-v6.6/Documentation/devicetree/bindings/leds/ |
| D | leds-el15203000.txt | 6 The board manages 3 LEDs and supports predefined blinking patterns
10 Doesn't have any hardware blinking pattern.
13 encoded with symbol 'S' (hex code 0x53). Supports blinking breathing pattern.
|
| D | pca963x.txt | 9 - nxp,hw-blink : use hardware blinking instead of software blinking
|
| D | leds-ns2.txt | 11 - modes-map: A mapping between LED modes (off, on or SATA activity blinking) and
|
| D | leds-spi-byte.txt | 13 accelerated blinking) might can be supported too.
|
| /Linux-v6.6/drivers/leds/blink/ |
| D | leds-lgm-sso.c | 110 unsigned int blinking:1; member
253 if (desc->hw_blink && !val && desc->blinking) { in sso_led_brightness_set()
254 desc->blinking = 0; in sso_led_brightness_set()
256 } else if (desc->hw_blink && val && !desc->blinking) { in sso_led_brightness_set()
257 desc->blinking = 1; in sso_led_brightness_set()
320 led->desc.blinking = 1; in sso_led_blink_set()
|
| D | Kconfig | 26 The driver supports hardware blinking and the LEDs can be configured
|
| /Linux-v6.6/drivers/net/phy/ |
| D | mediatek-ge-soc.c | 1140 bool blinking) in mt798x_phy_hw_led_blink_set() argument
1146 if (blinking) in mt798x_phy_hw_led_blink_set()
1156 blinking ? MTK_PHY_LED_BLINK_FORCE_BLINK : 0); in mt798x_phy_hw_led_blink_set()
1165 bool blinking = false; in mt798x_phy_led_blink_set() local
1172 blinking = true; in mt798x_phy_led_blink_set()
1177 err = mt798x_phy_hw_led_blink_set(phydev, index, blinking); in mt798x_phy_led_blink_set()
|
| /Linux-v6.6/Documentation/driver-api/80211/ |
| D | mac80211-advanced.rst | 12 Mac80211 supports various ways of blinking LEDs. Wherever possible,
|
| /Linux-v6.6/arch/arm/boot/dts/marvell/ |
| D | armada-xp-lenovo-ix4-300d.dts | 201 /* init blinking while booting */
|
| /Linux-v6.6/Documentation/driver-api/media/ |
| D | rc-core.rst | 31 The infrared transmission is done by blinking a infrared emitter using a
|
| /Linux-v6.6/Documentation/ABI/testing/ |
| D | sysfs-class-led-trigger-netdev | 75 If 1, the LED blinking in requested mode is offloaded to
|
| /Linux-v6.6/drivers/leds/trigger/ |
| D | Kconfig | 17 blinking the LED without any further software interaction.
|
