Searched refs:V8 (Results 1 – 25 of 28) sorted by relevance
12
| /Linux-v6.6/Documentation/hwmon/ |
| D | lochnagar.rst | 33 in1_input Measured voltage for 1V8 DSP (milliVolts)
34 in1_label "1V8 DSP"
35 curr2_input Measured current for 1V8 DSP (milliAmps)
36 curr2_label "1V8 DSP"
37 power2_average Measured average power for 1V8 DSP (microWatts)
39 power2_label "1V8 DSP"
40 in2_input Measured voltage for 1V8 CDC (milliVolts)
41 in2_label "1V8 CDC"
42 curr3_input Measured current for 1V8 CDC (milliAmps)
43 curr3_label "1V8 CDC"
[all …]
|
| /Linux-v6.6/drivers/regulator/ |
| D | pcap-regulator.c | 118 VREG_INFO(V8, PCAP_REG_VREG2, 5, 6, 16, 22),
227 VREG(V8), VREG(V9), VREG(V10), VREG(VAUX1), VREG(VAUX2), VREG(VAUX3),
|
| /Linux-v6.6/arch/arm/boot/dts/broadcom/ |
| D | bcm2835-rpi-cm1.dtsi | 30 regulator-name = "1V8";
|
| D | bcm2837-rpi-cm3.dtsi | 22 regulator-name = "1V8";
|
| /Linux-v6.6/include/linux/mfd/ |
| D | ezx-pcap.h | 120 #define V8 7 macro
|
| /Linux-v6.6/arch/arm/boot/dts/gemini/ |
| D | gemini-nas4220b.dts | 110 pins = "V8 GMAC0 RXDV", "T10 GMAC1 RXDV";
|
| D | gemini-sq201.dts | 185 pins = "V8 GMAC0 RXDV";
|
| D | gemini-sl93512r.dts | 222 pins = "U8 GMAC0 RXD0", "V8 GMAC0 RXD1",
|
| D | gemini-dlink-dns-313.dts | 260 pins = "U8 GMAC0 RXD0", "V8 GMAC0 RXD1",
|
| D | gemini-dlink-dir-685.dts | 401 pins = "V8 GMAC0 RXDV", "T10 GMAC1 RXDV",
|
| /Linux-v6.6/arch/arm/boot/dts/renesas/ |
| D | r8a73a4-ape6evm.dts | 58 regulator-name = "1V8";
|
| /Linux-v6.6/arch/arm/boot/dts/ti/omap/ |
| D | am335x-boneblue.dts | 196 AM33XX_PADCONF(AM335X_PIN_GPMC_AD5, PIN_INPUT_PULLUP, MUX_MODE1) /* (V8) gpmc_ad5.mmc1_dat5 */
481 "MMC1_DAT5", /* V8 */
|
| D | am335x-guardian.dts | 723 /* (V8) gpmc_ad5.gpmc_ad5 */
|
| /Linux-v6.6/arch/arm64/boot/dts/amlogic/ |
| D | meson-gxl-s905x-libretech-cc-v2.dts | 153 regulator-name = "VCC 1V8";
|
| D | meson-gxbb-odroidc2.dts | 279 gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
|
| /Linux-v6.6/arch/arm64/boot/dts/freescale/ |
| D | imx8mm-kontron-sl.dtsi | 147 regulator-name = "+1V8 (BUCK5)";
|
| D | imx8mq-mnt-reform2.dts | 71 regulator-name = "1V8";
|
| D | imx8mm-kontron-osm-s.dtsi | 153 regulator-name = "+1V8 (BUCK5)";
|
| /Linux-v6.6/tools/perf/Documentation/ |
| D | perf-inject.txt | 79 if you are monitoring environment using JIT runtimes, such as Java, DART or V8.
|
| /Linux-v6.6/Documentation/arch/arm64/ |
| D | sve.rst | 523 Z8 | : * V8 |
556 This follows from the way these bits are mapped to V8..V15, which are caller-
580 * V8 | |
|
| /Linux-v6.6/arch/arm/boot/dts/st/ |
| D | stm32mp15xx-dhcor-avenger96.dtsi | 8 /* Avenger96 uses DHCOR SoM configured for 1V8 IO operation */
|
| D | ste-ux500-samsung-skomer.dts | 366 /* Intended for 1V8 for touchscreen but actually left unused */
|
| /Linux-v6.6/arch/arm64/boot/dts/xilinx/ |
| D | zynqmp-zcu100-revC.dts | 521 interrupts = <76 IRQ_TYPE_EDGE_RISING>; /* MIO76 WLAN_IRQ 1V8 */
|
| /Linux-v6.6/arch/arm64/boot/dts/ti/ |
| D | k3-am642-sk.dts | 352 AM64X_IOPAD(0x00c4, PIN_OUTPUT_PULLUP, 7) /* (V8) GPIO0_48 */
|
| D | k3-am642-tqma64xxl-mbax4xxl.dts | 726 /* (V8) PRG1_PRU0_GPO3.PRG1_RGMII1_RD3 */
|
12
