Home
last modified time | relevance | path

Searched refs:SER_RS485_RX_DURING_TX (Results 1 – 13 of 13) sorted by relevance

/Linux-v6.6/drivers/tty/serial/8250/
D8250_bcm2835aux.c54 if (!(up->port.rs485.flags & SER_RS485_RX_DURING_TX)) { in bcm2835aux_rs485_start_tx()
78 if (!(up->port.rs485.flags & SER_RS485_RX_DURING_TX)) { in bcm2835aux_rs485_stop_tx()
D8250_dwlib.c191 if (rs485->flags & SER_RS485_RX_DURING_TX) in dw8250_rs485_config()
237 .flags = SER_RS485_ENABLED | SER_RS485_RX_DURING_TX | SER_RS485_RTS_ON_SEND |
D8250_exar.c468 if (rs485->flags & SER_RS485_RX_DURING_TX) in iot2040_rs485_config()
493 .flags = SER_RS485_ENABLED | SER_RS485_RX_DURING_TX | SER_RS485_TERMINATE_BUS,
D8250_port.c605 SER_RS485_TERMINATE_BUS | SER_RS485_RX_DURING_TX,
1428 if (!(p->port.rs485.flags & SER_RS485_RX_DURING_TX)) { in serial8250_em485_stop_tx()
1579 if (!(up->port.rs485.flags & SER_RS485_RX_DURING_TX)) in serial8250_em485_start_tx()
/Linux-v6.6/include/uapi/linux/
Dserial.h146 #define SER_RS485_RX_DURING_TX (1 << 4) macro
/Linux-v6.6/drivers/tty/serial/
Domap-serial.c339 !(up->port.rs485.flags & SER_RS485_RX_DURING_TX)) in serial_omap_put_char()
382 !(port->rs485.flags & SER_RS485_RX_DURING_TX)) in serial_omap_start_tx()
449 !(up->port.rs485.flags & SER_RS485_RX_DURING_TX) && in serial_omap_rlsi()
503 !(up->port.rs485.flags & SER_RS485_RX_DURING_TX) && in serial_omap_rdi()
1536 SER_RS485_RX_DURING_TX,
Dimx.c691 if (!(port->rs485.flags & SER_RS485_RX_DURING_TX) && in imx_uart_start_tx()
1934 rs485conf->flags |= SER_RS485_RX_DURING_TX; in imx_uart_rs485_config()
1947 rs485conf->flags & SER_RS485_RX_DURING_TX) in imx_uart_rs485_config()
1952 !!(rs485conf->flags & SER_RS485_RX_DURING_TX)); in imx_uart_rs485_config()
2220 SER_RS485_RX_DURING_TX,
2351 !(sport->port.rs485.flags & SER_RS485_RX_DURING_TX))) in imx_uart_probe()
Dmax310x.c1031 if (!(one->port.rs485.flags & SER_RS485_RX_DURING_TX)) in max310x_rs_proc()
1084 if (!(port->rs485.flags & SER_RS485_RX_DURING_TX)) in max310x_startup()
1263 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RX_DURING_TX,
Dstm32-usart.c231 !!(rs485conf->flags & SER_RS485_RX_DURING_TX)); in stm32_usart_config_rs485()
233 rs485conf->flags |= SER_RS485_RX_DURING_TX; in stm32_usart_config_rs485()
1505 SER_RS485_RX_DURING_TX,
Dserial_core.c1301 SER_RS485_RTS_AFTER_SEND | SER_RS485_RX_DURING_TX | \
3587 rs485conf->flags &= ~(SER_RS485_RX_DURING_TX | SER_RS485_ENABLED | in uart_get_rs485_mode()
3593 rs485conf->flags |= SER_RS485_RX_DURING_TX; in uart_get_rs485_mode()
3618 rx_during_tx_gpio_flag = (rs485conf->flags & SER_RS485_RX_DURING_TX) ? in uart_get_rs485_mode()
Datmel_serial.c229 !(port->rs485.flags & SER_RS485_RX_DURING_TX)) || in atmel_uart_is_half_duplex()
306 if (rs485conf->flags & SER_RS485_RX_DURING_TX) in atmel_config_rs485()
2525 .flags = SER_RS485_ENABLED | SER_RS485_RTS_AFTER_SEND | SER_RS485_RX_DURING_TX,
Damba-pl011.c1448 if (!(port->rs485.flags & SER_RS485_RX_DURING_TX)) in pl011_rs485_tx_start()
2789 SER_RS485_RX_DURING_TX,
/Linux-v6.6/Documentation/driver-api/serial/
Dserial-rs485.rst94 rs485conf.flags |= SER_RS485_RX_DURING_TX;