Searched refs:GPIO28 (Results 1 – 19 of 19) sorted by relevance
| /Linux-v6.6/arch/arm/mach-pxa/ |
| D | mfp-pxa25x.h | 96 #define GPIO28_AC97_BITCLK MFP_CFG_IN(GPIO28, AF1)
103 #define GPIO28_I2S_BITCLK_IN MFP_CFG_IN(GPIO28, AF2)
104 #define GPIO28_I2S_BITCLK_OUT MFP_CFG_OUT(GPIO28, AF1, DRIVE_LOW)
|
| D | mfp-pxa27x.h | 198 #define GPIO28_AC97_BITCLK MFP_CFG_IN(GPIO28, AF1)
204 #define GPIO28_I2S_BITCLK_IN MFP_CFG_IN(GPIO28, AF2)
205 #define GPIO28_I2S_BITCLK_OUT MFP_CFG_OUT(GPIO28, AF1, DRIVE_LOW)
218 #define GPIO28_SSP1_SFRM MFP_CFG_IN(GPIO28, AF3)
|
| D | mfp-pxa2xx.h | 82 #define GPIO28_GPIO MFP_CFG_IN(GPIO28, AF0)
|
| D | mfp-pxa300.h | 54 #define GPIO28_AC97_SYNC MFP_CFG(GPIO28, AF1)
272 #define GPIO28_SSP2_TXD MFP_CFG(GPIO28, AF5)
273 #define GPIO28_SSP2_RXD MFP_CFG(GPIO28, AF2)
491 #define GPIO28_U2D_OPMODE_1 MFP_CFG(GPIO28, AF4)
|
| D | mfp-pxa3xx.h | 40 #define GPIO28_GPIO MFP_CFG(GPIO28, AF0)
|
| D | mfp-pxa320.h | 212 #define GPIO28_MMC2_CLK MFP_CFG_LPM(GPIO28, AF4, PULL_HIGH)
|
| /Linux-v6.6/arch/arm/boot/dts/broadcom/ |
| D | bcm2837-rpi-cm3-io3.dts | 47 "GPIO28",
|
| D | bcm2835-rpi-cm1-io1.dts | 47 "GPIO28",
|
| D | bcm2835-rpi-b.dts | 58 "GPIO28",
|
| D | bcm2835-rpi-b-rev2.dts | 58 "GPIO28",
|
| /Linux-v6.6/drivers/pinctrl/ |
| D | pinctrl-lantiq.h | 135 GPIO28, enumerator
|
| D | pinctrl-xway.c | 143 MFP_XWAY(GPIO28, GPIO, MII, EBU, SDIO),
271 MFP_XWAY(GPIO28, GPIO, GPT, MII, SDIO),
314 static const unsigned danube_pins_gpt1[] = {GPIO28};
446 MFP_XWAY(GPIO28, GPIO, GPT, NONE, SDIO),
517 static const unsigned xrx100_pins_gpt1[] = {GPIO28};
659 MFP_XWAY(GPIO28, GPIO, GPT, PCI, SDIO),
745 static const unsigned xrx200_pins_gpt1[] = {GPIO28};
754 static const unsigned xrx200_pins_pci_gnt1[] = {GPIO28};
915 MFP_XWAY(GPIO28, NONE, NONE, NONE, NONE),
|
| /Linux-v6.6/arch/arm64/boot/dts/rockchip/ |
| D | rk3566-soquartz-cm4.dts | 82 * pin 35 - ID_SC(GPIO28) - i2c3_scl_m0, pullup to vcc_3v3
|
| D | rk3566-soquartz-blade.dts | 78 * pin 35 - ID_SC(GPIO28) - i2c3_scl_m0, pullup to vcc_3v3
|
| D | rk3566-soquartz-model-a.dts | 105 * pin 35 - ID_SC(GPIO28) - i2c3_scl_m0, pullup to vcc_3v3
|
| /Linux-v6.6/Documentation/devicetree/bindings/pinctrl/ |
| D | ste,abx500.txt | 132 pins = "GPIO28";
|
| D | nuvoton,npcm7xx-pinctrl.txt | 52 "GPIO27/SMB5SCL", "GPIO28/SMB4SDA", "GPIO29/SMB4SCL", "GPIO30/SMB3SDA",
|
| /Linux-v6.6/arch/arm64/boot/dts/bitmain/ |
| D | bm1880-sophon-edge.dts | 84 "NC", /* GPIO28 */
|
| /Linux-v6.6/arch/arm/boot/dts/ti/keystone/ |
| D | keystone-k2l.dtsi | 160 * GPIO_EMU_SEL[28]: 0-GPIO28, 1-EMU30
|
