/Linux-v6.6/arch/powerpc/platforms/cell/ |
D | Kconfig | 27 bool "IBM Cell Blade" 42 menu "Cell Broadband Engine options" 61 bool "RAS features for bare metal Cell BE" 66 bool "IBM Cell Blade Pinhole reset button" 70 Support Pinhole Resetbutton on IBM Cell blades. 74 tristate "IBM Cell Blade power button" 78 Support Powerbutton on IBM Cell blades. 93 It is used in some IBM Cell blades.
|
/Linux-v6.6/Documentation/devicetree/bindings/reset/ |
D | ti-syscon-reset.txt | 33 Cell #1 : offset of the reset assert control 35 Cell #2 : bit position of the reset in the reset 37 Cell #3 : offset of the reset deassert control 39 Cell #4 : bit position of the reset in the reset 41 Cell #5 : offset of the reset status register 43 Cell #6 : bit position of the reset in the 45 Cell #7 : Flags used to control reset behavior,
|
/Linux-v6.6/Documentation/powerpc/ |
D | isa-versions.rst | 20 Cell PPU - Power ISA v2.02 with some minor exceptions 54 Cell PPU Yes 74 Cell PPU No 94 Cell PPU No
|
D | cpu_families.rst | 85 | POWER6 | <-?-> | Cell |
|
D | elf_hwcaps.rst | 127 The processor is Cell.
|
/Linux-v6.6/drivers/gpu/drm/amd/pm/powerplay/inc/ |
D | smu75.h | 679 VFT_CELL_t Cell[TEMP_RANGE_MAXSTEPS][NUM_VFT_COLUMNS]; member 715 VFT_CELL_t Cell[NUM_VFT_COLUMNS]; member 720 VFT_CELL_t Cell[NUM_VFT_COLUMNS]; member 725 VFT_CELL_t Cell[NUM_VFT_COLUMNS]; member 730 VFT_CELL_t Cell[NUM_VFT_COLUMNS]; member
|
D | smu74.h | 782 VFT_CELL_t Cell[TEMP_RANGE_MAXSTEPS][NUM_VFT_COLUMNS]; member 796 VFT_CELL_t Cell[NUM_VFT_COLUMNS]; member 812 VFT_CELL_t Cell[NUM_VFT_COLUMNS]; member
|
D | smu73.h | 699 VFT_CELL_t Cell[TEMP_RANGE_MAXSTEPS][NUM_VFT_COLUMNS]; member
|
/Linux-v6.6/Documentation/devicetree/bindings/interrupt-controller/ |
D | snps,archs-intc.txt | 9 Single Cell "interrupts" property of a device specifies the IRQ number
|
D | snps,arc700-intc.txt | 12 Single Cell "interrupts" property of a device specifies the IRQ number
|
/Linux-v6.6/drivers/net/ethernet/ibm/emac/ |
D | Kconfig | 10 Axon southbridge for Cell.
|
/Linux-v6.6/Documentation/devicetree/bindings/pinctrl/ |
D | pinctrl-st.txt | 69 - First Cell: represents the external gpio interrupt number local to the 71 - Second Cell: flags to identify the type of the interrupt
|
/Linux-v6.6/drivers/cpufreq/ |
D | Kconfig.powerpc | 7 This adds the cpufreq driver for Cell BE processors.
|
/Linux-v6.6/drivers/net/ethernet/toshiba/ |
D | Kconfig | 49 Cell Processor-Based Blades from IBM.
|
/Linux-v6.6/Documentation/devicetree/bindings/gpio/ |
D | spear_spics.txt | 4 Cell spi controller through its system registers, which otherwise remains under
|
/Linux-v6.6/arch/powerpc/platforms/ps3/ |
D | Kconfig | 55 per device dynamic DMA page table management provided by the Cell 167 profiling support of the Cell processor with programs like
|
/Linux-v6.6/Documentation/devicetree/bindings/phy/ |
D | phy-miphy365x.txt | 22 Cell after port phandle is device type from:
|
D | phy-miphy28lp.txt | 20 Cell after port phandle is device type from:
|
/Linux-v6.6/Documentation/translations/zh_CN/admin-guide/ |
D | README.rst | 33 PowerPC64、ARM、Hitachi SuperH、Cell、IBM S/390、MIPS、HP PA-RISC、Intel
|
/Linux-v6.6/Documentation/translations/zh_TW/admin-guide/ |
D | README.rst | 36 PowerPC64、ARM、Hitachi SuperH、Cell、IBM S/390、MIPS、HP PA-RISC、Intel
|
/Linux-v6.6/Documentation/filesystems/spufs/ |
D | spu_create.rst | 25 the Cell Broadband Engine Architecture in order to access Synergistic
|
D | spu_run.rst | 25 Cell Broadband Engine Architecture in order to access Synergistic Pro-
|
/Linux-v6.6/Documentation/scsi/ |
D | aic79xx.rst | 398 :Definition: Set IO Cell precompensation value on a per-controller basis. 421 :Definition: Set IO Cell slew rate on a per-controller basis. 444 :Definition: Set IO Cell signal amplitude on a per-controller basis.
|
/Linux-v6.6/Documentation/devicetree/bindings/clock/ |
D | qoriq-clock.txt | 83 Type# Name Index Cell
|
/Linux-v6.6/Documentation/filesystems/ |
D | 9p.rst | 29 * CellFS: A New Programming Model for the Cell BE
|