1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright (C) 2018 Oleksij Rempel <linux@rempel-privat.de> 4 * 5 * Driver for Alcor Micro AU6601 and AU6621 controllers 6 */ 7 8 #ifndef __ALCOR_PCI_H 9 #define __ALCOR_PCI_H 10 11 #define ALCOR_SD_CARD 0 12 #define ALCOR_MS_CARD 1 13 14 #define DRV_NAME_ALCOR_PCI_SDMMC "alcor_sdmmc" 15 #define DRV_NAME_ALCOR_PCI_MS "alcor_ms" 16 17 #define PCI_ID_ALCOR_MICRO 0x1AEA 18 #define PCI_ID_AU6601 0x6601 19 #define PCI_ID_AU6621 0x6621 20 #define PCI_ID_AU6625 0x6625 21 22 #define MHZ_TO_HZ(freq) ((freq) * 1000 * 1000) 23 24 #define AU6601_BASE_CLOCK 31000000 25 #define AU6601_MIN_CLOCK 150000 26 #define AU6601_MAX_CLOCK 208000000 27 #define AU6601_MAX_DMA_SEGMENTS 64 28 #define AU6601_MAX_PIO_SEGMENTS 1 29 #define AU6601_MAX_DMA_BLOCK_SIZE 0x1000 30 #define AU6601_MAX_PIO_BLOCK_SIZE 0x200 31 #define AU6601_MAX_DMA_BLOCKS 1 32 #define AU6601_DMA_LOCAL_SEGMENTS 1 33 34 /* registers spotter by reverse engineering but still 35 * with unknown functionality: 36 * 0x10 - ADMA phy address. AU6621 only? 37 * 0x51 - LED ctrl? 38 * 0x52 - unknown 39 * 0x61 - LED related? Always toggled BIT0 40 * 0x63 - Same as 0x61? 41 * 0x77 - unknown 42 */ 43 44 /* SDMA phy address. Higher then 0x0800.0000? 45 * The au6601 and au6621 have different DMA engines with different issues. One 46 * For example au6621 engine is triggered by addr change. No other interaction 47 * is needed. This means, if we get two buffers with same address, then engine 48 * will stall. 49 */ 50 #define AU6601_REG_SDMA_ADDR 0x00 51 #define AU6601_SDMA_MASK 0xffffffff 52 53 #define AU6601_DMA_BOUNDARY 0x05 54 #define AU6621_DMA_PAGE_CNT 0x05 55 /* PIO */ 56 #define AU6601_REG_BUFFER 0x08 57 /* ADMA ctrl? AU6621 only. */ 58 #define AU6621_DMA_CTRL 0x0c 59 #define AU6621_DMA_ENABLE BIT(0) 60 /* CMD index */ 61 #define AU6601_REG_CMD_OPCODE 0x23 62 /* CMD parametr */ 63 #define AU6601_REG_CMD_ARG 0x24 64 /* CMD response 4x4 Bytes */ 65 #define AU6601_REG_CMD_RSP0 0x30 66 #define AU6601_REG_CMD_RSP1 0x34 67 #define AU6601_REG_CMD_RSP2 0x38 68 #define AU6601_REG_CMD_RSP3 0x3C 69 /* default timeout set to 125: 125 * 40ms = 5 sec 70 * how exactly it is calculated? 71 */ 72 #define AU6601_TIME_OUT_CTRL 0x69 73 /* Block size for SDMA or PIO */ 74 #define AU6601_REG_BLOCK_SIZE 0x6c 75 /* Some power related reg, used together with AU6601_OUTPUT_ENABLE */ 76 #define AU6601_POWER_CONTROL 0x70 77 78 /* PLL ctrl */ 79 #define AU6601_CLK_SELECT 0x72 80 #define AU6601_CLK_OVER_CLK 0x80 81 #define AU6601_CLK_384_MHZ 0x30 82 #define AU6601_CLK_125_MHZ 0x20 83 #define AU6601_CLK_48_MHZ 0x10 84 #define AU6601_CLK_EXT_PLL 0x04 85 #define AU6601_CLK_X2_MODE 0x02 86 #define AU6601_CLK_ENABLE 0x01 87 #define AU6601_CLK_31_25_MHZ 0x00 88 89 #define AU6601_CLK_DIVIDER 0x73 90 91 #define AU6601_INTERFACE_MODE_CTRL 0x74 92 #define AU6601_DLINK_MODE 0x80 93 #define AU6601_INTERRUPT_DELAY_TIME 0x40 94 #define AU6601_SIGNAL_REQ_CTRL 0x30 95 #define AU6601_MS_CARD_WP BIT(3) 96 #define AU6601_SD_CARD_WP BIT(0) 97 98 /* same register values are used for: 99 * - AU6601_OUTPUT_ENABLE 100 * - AU6601_POWER_CONTROL 101 */ 102 #define AU6601_ACTIVE_CTRL 0x75 103 #define AU6601_XD_CARD BIT(4) 104 /* AU6601_MS_CARD_ACTIVE - will cativate MS card section? */ 105 #define AU6601_MS_CARD BIT(3) 106 #define AU6601_SD_CARD BIT(0) 107 108 /* card slot state. It should automatically detect type of 109 * the card 110 */ 111 #define AU6601_DETECT_STATUS 0x76 112 #define AU6601_DETECT_EN BIT(7) 113 #define AU6601_MS_DETECTED BIT(3) 114 #define AU6601_SD_DETECTED BIT(0) 115 #define AU6601_DETECT_STATUS_M 0xf 116 117 #define AU6601_REG_SW_RESET 0x79 118 #define AU6601_BUF_CTRL_RESET BIT(7) 119 #define AU6601_RESET_DATA BIT(3) 120 #define AU6601_RESET_CMD BIT(0) 121 122 #define AU6601_OUTPUT_ENABLE 0x7a 123 124 #define AU6601_PAD_DRIVE0 0x7b 125 #define AU6601_PAD_DRIVE1 0x7c 126 #define AU6601_PAD_DRIVE2 0x7d 127 /* read EEPROM? */ 128 #define AU6601_FUNCTION 0x7f 129 130 #define AU6601_CMD_XFER_CTRL 0x81 131 #define AU6601_CMD_17_BYTE_CRC 0xc0 132 #define AU6601_CMD_6_BYTE_WO_CRC 0x80 133 #define AU6601_CMD_6_BYTE_CRC 0x40 134 #define AU6601_CMD_START_XFER 0x20 135 #define AU6601_CMD_STOP_WAIT_RDY 0x10 136 #define AU6601_CMD_NO_RESP 0x00 137 138 #define AU6601_REG_BUS_CTRL 0x82 139 #define AU6601_BUS_WIDTH_4BIT 0x20 140 #define AU6601_BUS_WIDTH_8BIT 0x10 141 #define AU6601_BUS_WIDTH_1BIT 0x00 142 143 #define AU6601_DATA_XFER_CTRL 0x83 144 #define AU6601_DATA_WRITE BIT(7) 145 #define AU6601_DATA_DMA_MODE BIT(6) 146 #define AU6601_DATA_START_XFER BIT(0) 147 148 #define AU6601_DATA_PIN_STATE 0x84 149 #define AU6601_BUS_STAT_CMD BIT(15) 150 /* BIT(4) - BIT(7) are permanently 1. 151 * May be reserved or not attached DAT4-DAT7 152 */ 153 #define AU6601_BUS_STAT_DAT3 BIT(3) 154 #define AU6601_BUS_STAT_DAT2 BIT(2) 155 #define AU6601_BUS_STAT_DAT1 BIT(1) 156 #define AU6601_BUS_STAT_DAT0 BIT(0) 157 #define AU6601_BUS_STAT_DAT_MASK 0xf 158 159 #define AU6601_OPT 0x85 160 #define AU6601_OPT_CMD_LINE_LEVEL 0x80 161 #define AU6601_OPT_NCRC_16_CLK BIT(4) 162 #define AU6601_OPT_CMD_NWT BIT(3) 163 #define AU6601_OPT_STOP_CLK BIT(2) 164 #define AU6601_OPT_DDR_MODE BIT(1) 165 #define AU6601_OPT_SD_18V BIT(0) 166 167 #define AU6601_CLK_DELAY 0x86 168 #define AU6601_CLK_DATA_POSITIVE_EDGE 0x80 169 #define AU6601_CLK_CMD_POSITIVE_EDGE 0x40 170 #define AU6601_CLK_POSITIVE_EDGE_ALL (AU6601_CLK_CMD_POSITIVE_EDGE \ 171 | AU6601_CLK_DATA_POSITIVE_EDGE) 172 173 174 #define AU6601_REG_INT_STATUS 0x90 175 #define AU6601_REG_INT_ENABLE 0x94 176 #define AU6601_INT_DATA_END_BIT_ERR BIT(22) 177 #define AU6601_INT_DATA_CRC_ERR BIT(21) 178 #define AU6601_INT_DATA_TIMEOUT_ERR BIT(20) 179 #define AU6601_INT_CMD_INDEX_ERR BIT(19) 180 #define AU6601_INT_CMD_END_BIT_ERR BIT(18) 181 #define AU6601_INT_CMD_CRC_ERR BIT(17) 182 #define AU6601_INT_CMD_TIMEOUT_ERR BIT(16) 183 #define AU6601_INT_ERROR BIT(15) 184 #define AU6601_INT_OVER_CURRENT_ERR BIT(8) 185 #define AU6601_INT_CARD_INSERT BIT(7) 186 #define AU6601_INT_CARD_REMOVE BIT(6) 187 #define AU6601_INT_READ_BUF_RDY BIT(5) 188 #define AU6601_INT_WRITE_BUF_RDY BIT(4) 189 #define AU6601_INT_DMA_END BIT(3) 190 #define AU6601_INT_DATA_END BIT(1) 191 #define AU6601_INT_CMD_END BIT(0) 192 193 #define AU6601_INT_NORMAL_MASK 0x00007FFF 194 #define AU6601_INT_ERROR_MASK 0xFFFF8000 195 196 #define AU6601_INT_CMD_MASK (AU6601_INT_CMD_END | \ 197 AU6601_INT_CMD_TIMEOUT_ERR | AU6601_INT_CMD_CRC_ERR | \ 198 AU6601_INT_CMD_END_BIT_ERR | AU6601_INT_CMD_INDEX_ERR) 199 #define AU6601_INT_DATA_MASK (AU6601_INT_DATA_END | AU6601_INT_DMA_END | \ 200 AU6601_INT_READ_BUF_RDY | AU6601_INT_WRITE_BUF_RDY | \ 201 AU6601_INT_DATA_TIMEOUT_ERR | AU6601_INT_DATA_CRC_ERR | \ 202 AU6601_INT_DATA_END_BIT_ERR) 203 #define AU6601_INT_ALL_MASK ((u32)-1) 204 205 /* MS_CARD mode registers */ 206 207 #define AU6601_MS_STATUS 0xa0 208 209 #define AU6601_MS_BUS_MODE_CTRL 0xa1 210 #define AU6601_MS_BUS_8BIT_MODE 0x03 211 #define AU6601_MS_BUS_4BIT_MODE 0x01 212 #define AU6601_MS_BUS_1BIT_MODE 0x00 213 214 #define AU6601_MS_TPC_CMD 0xa2 215 #define AU6601_MS_TPC_READ_PAGE_DATA 0x02 216 #define AU6601_MS_TPC_READ_REG 0x04 217 #define AU6601_MS_TPC_GET_INT 0x07 218 #define AU6601_MS_TPC_WRITE_PAGE_DATA 0x0D 219 #define AU6601_MS_TPC_WRITE_REG 0x0B 220 #define AU6601_MS_TPC_SET_RW_REG_ADRS 0x08 221 #define AU6601_MS_TPC_SET_CMD 0x0E 222 #define AU6601_MS_TPC_EX_SET_CMD 0x09 223 #define AU6601_MS_TPC_READ_SHORT_DATA 0x03 224 #define AU6601_MS_TPC_WRITE_SHORT_DATA 0x0C 225 226 #define AU6601_MS_TRANSFER_MODE 0xa3 227 #define AU6601_MS_XFER_INT_TIMEOUT_CHK BIT(2) 228 #define AU6601_MS_XFER_DMA_ENABLE BIT(1) 229 #define AU6601_MS_XFER_START BIT(0) 230 231 #define AU6601_MS_DATA_PIN_STATE 0xa4 232 233 #define AU6601_MS_INT_STATUS 0xb0 234 #define AU6601_MS_INT_ENABLE 0xb4 235 #define AU6601_MS_INT_OVER_CURRENT_ERROR BIT(23) 236 #define AU6601_MS_INT_DATA_CRC_ERROR BIT(21) 237 #define AU6601_MS_INT_INT_TIMEOUT BIT(20) 238 #define AU6601_MS_INT_INT_RESP_ERROR BIT(19) 239 #define AU6601_MS_INT_CED_ERROR BIT(18) 240 #define AU6601_MS_INT_TPC_TIMEOUT BIT(16) 241 #define AU6601_MS_INT_ERROR BIT(15) 242 #define AU6601_MS_INT_CARD_INSERT BIT(7) 243 #define AU6601_MS_INT_CARD_REMOVE BIT(6) 244 #define AU6601_MS_INT_BUF_READ_RDY BIT(5) 245 #define AU6601_MS_INT_BUF_WRITE_RDY BIT(4) 246 #define AU6601_MS_INT_DMA_END BIT(3) 247 #define AU6601_MS_INT_TPC_END BIT(1) 248 249 #define AU6601_MS_INT_DATA_MASK 0x00000038 250 #define AU6601_MS_INT_TPC_MASK 0x003d8002 251 #define AU6601_MS_INT_TPC_ERROR 0x003d0000 252 253 #define ALCOR_PCIE_LINK_CTRL_OFFSET 0x10 254 #define ALCOR_PCIE_LINK_CAP_OFFSET 0x0c 255 #define ALCOR_CAP_START_OFFSET 0x34 256 257 struct alcor_dev_cfg { 258 u8 dma; 259 }; 260 261 struct alcor_pci_priv { 262 struct pci_dev *pdev; 263 struct pci_dev *parent_pdev; 264 struct device *dev; 265 void __iomem *iobase; 266 unsigned int irq; 267 268 unsigned long id; /* idr id */ 269 270 struct alcor_dev_cfg *cfg; 271 }; 272 273 void alcor_write8(struct alcor_pci_priv *priv, u8 val, unsigned int addr); 274 void alcor_write16(struct alcor_pci_priv *priv, u16 val, unsigned int addr); 275 void alcor_write32(struct alcor_pci_priv *priv, u32 val, unsigned int addr); 276 void alcor_write32be(struct alcor_pci_priv *priv, u32 val, unsigned int addr); 277 u8 alcor_read8(struct alcor_pci_priv *priv, unsigned int addr); 278 u32 alcor_read32(struct alcor_pci_priv *priv, unsigned int addr); 279 u32 alcor_read32be(struct alcor_pci_priv *priv, unsigned int addr); 280 #endif 281
