| /Linux-v6.1/Documentation/devicetree/bindings/mfd/ |
| D | mxs-lradc.txt | 10 - fsl,lradc-touchscreen-wires: Number of wires used to connect the touchscreen
13 disabled. 5 wires is valid for i.MX28 SoC only.
29 fsl,lradc-touchscreen-wires = <4>;
41 fsl,lradc-touchscreen-wires = <5>;
|
| /Linux-v6.1/Documentation/devicetree/bindings/input/touchscreen/ |
| D | fsl-mx25-tcq.txt | 11 - fsl,wires: Should be '<4>' or '<5>'
33 fsl,wires = <4>;
|
| /Linux-v6.1/drivers/input/touchscreen/ |
| D | ti_am335x_tsc.c | 52 unsigned int wires; member
136 switch (ts_dev->wires) { in titsc_step_config()
165 switch (ts_dev->wires) { in titsc_step_config()
358 err = of_property_read_u32(node, "ti,wires", &ts_dev->wires); in titsc_parse_dt()
361 switch (ts_dev->wires) { in titsc_parse_dt()
|
| D | fsl-imx25-tcq.c | 436 u32 wires; in mx25_tcq_parse_dt() local
445 error = of_property_read_u32(np, "fsl,wires", &wires); in mx25_tcq_parse_dt()
451 if (wires == 4) { in mx25_tcq_parse_dt()
454 dev_err(&pdev->dev, "%u-wire mode not supported\n", wires); in mx25_tcq_parse_dt()
|
| /Linux-v6.1/include/linux/platform_data/ |
| D | mmc-davinci.h | 20 u8 wires; member
|
| D | mmc-omap.h | 46 u8 wires; /* Used for the MMC driver on omap1 and 2420 */ member
|
| /Linux-v6.1/Documentation/devicetree/bindings/display/tilcdc/ |
| D | tilcdc.txt | 25 - "crossed" indicates wiring that has blue and red wires
44 the wires work as they should (LCD_DATA[0:4] is for Blue[3:7]),
|
| /Linux-v6.1/arch/arm/mach-omap1/ |
| D | devices.c | 91 if (mmc_controller->slots[0].wires == 4 && !cpu_is_omap7xx()) { in omap1_mmc_mux()
107 if (mmc_controller->slots[1].wires == 4) { in omap1_mmc_mux()
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | sama5d3xdm.dtsi | 25 atmel,adc-ts-wires = <4>;
|
| D | at91-cosino_mega2560.dts | 23 atmel,adc-ts-wires = <4>;
|
| D | at91sam9x5dm.dtsi | 58 atmel,adc-ts-wires = <4>;
|
| D | imx6ul-ccimx6ulsbcpro.dts | 385 pinctrl_uart2_4wires: uart2grp-4wires {
394 pinctrl_uart3_2wires: uart3grp-2wires {
|
| D | at91-cosino.dtsi | 39 atmel,adc-ts-wires = <4>;
|
| D | imx23-evk.dts | 105 fsl,lradc-touchscreen-wires = <4>;
|
| D | imx28-cfa10058.dts | 79 fsl,lradc-touchscreen-wires = <4>;
|
| D | at91-sama5d4_ma5d4evk.dts | 87 atmel,adc-ts-wires = <4>;
|
| D | imx28-cfa10055.dts | 120 fsl,lradc-touchscreen-wires = <4>;
|
| D | at91sam9x5ek.dtsi | 36 atmel,adc-ts-wires = <4>;
|
| D | imx28-cfa10057.dts | 106 fsl,lradc-touchscreen-wires = <4>;
|
| /Linux-v6.1/drivers/gpu/drm/amd/acp/ |
| D | Kconfig | 12 This adds the ACP (Audio CoProcessor) IP driver and wires
|
| /Linux-v6.1/Documentation/devicetree/bindings/sound/ |
| D | mt6358.txt | 17 channels of PDM signal. 0 means two wires, 1 means one wire. Default
|
| /Linux-v6.1/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-thermocouple | 17 such as those caused by broken thermocouple wires.
|
| /Linux-v6.1/Documentation/driver-api/gpio/ |
| D | drivers-on-gpio.rst | 26 mouse cable and connect the wires to GPIO lines or solder a mouse connector
49 (two wires, SDA and SCL lines) by hammering (bitbang) two GPIO lines. It will
54 of wires, at least SCK and optionally MISO, MOSI and chip select lines) using
|
| /Linux-v6.1/arch/arm/mach-davinci/ |
| D | board-dm355-leopard.c | 199 .wires = 4,
|
| /Linux-v6.1/Documentation/devicetree/bindings/interrupt-controller/ |
| D | marvell,icu.txt | 7 requests on input wires to MSG memory mapped transactions to the GIC.
|
