| /Linux-v6.1/arch/arm64/boot/dts/arm/ |
| D | corstone1000.dtsi | 89 uartclk: uartclk { label
94 clock-output-names = "uartclk";
128 clocks = <&uartclk>, <&refclk100mhz>;
129 clock-names = "uartclk", "apb_pclk";
136 clocks = <&uartclk>, <&refclk100mhz>;
137 clock-names = "uartclk", "apb_pclk";
|
| D | foundation-v8.dtsi | 196 clock-names = "uartclk", "apb_pclk";
204 clock-names = "uartclk", "apb_pclk";
212 clock-names = "uartclk", "apb_pclk";
220 clock-names = "uartclk", "apb_pclk";
|
| /Linux-v6.1/arch/arm/mach-omap1/ |
| D | serial.c | 71 .uartclk = OMAP16XX_BASE_BAUD * 16,
79 .uartclk = OMAP16XX_BASE_BAUD * 16,
87 .uartclk = OMAP16XX_BASE_BAUD * 16,
117 serial_platform_data[0].uartclk = OMAP1510_BASE_BAUD * 16; in omap_serial_init()
118 serial_platform_data[1].uartclk = OMAP1510_BASE_BAUD * 16; in omap_serial_init()
119 serial_platform_data[2].uartclk = OMAP1510_BASE_BAUD * 16; in omap_serial_init()
|
| /Linux-v6.1/drivers/tty/serial/8250/ |
| D | 8250_acorn.c | 27 unsigned int uartclk; member
65 uart.port.uartclk = type->uartclk; in serial_card_probe()
96 .uartclk = 7372800,
103 .uartclk = 3686400,
|
| D | 8250_bcm2835aux.c | 93 unsigned int uartclk; in bcm2835aux_serial_probe() local
167 uartclk = clk_get_rate(data->clk); in bcm2835aux_serial_probe()
168 if (!uartclk) { in bcm2835aux_serial_probe()
169 ret = device_property_read_u32(&pdev->dev, "clock-frequency", &uartclk); in bcm2835aux_serial_probe()
181 up.port.uartclk = uartclk * 2; in bcm2835aux_serial_probe()
|
| D | 8250_hp300.c | 116 port.uartclk = HPAPCI_BAUD_BASE * 16; in hp300_setup_serial_console()
133 port.uartclk = HPDCA_BAUD_BASE * 16; in hp300_setup_serial_console()
175 uart.port.uartclk = HPDCA_BAUD_BASE * 16; in hpdca_init_one()
257 uart.port.uartclk = HPAPCI_BAUD_BASE * 16; in hp300_8250_init()
|
| /Linux-v6.1/arch/arm/mach-pxa/ |
| D | capc7117.c | 86 .uartclk = TI16C752_UARTCLK
95 .uartclk = TI16C752_UARTCLK
104 .uartclk = TI16C752_UARTCLK
113 .uartclk = TI16C752_UARTCLK
|
| D | zeus.c | 242 .uartclk = 14745600,
251 .uartclk = 14745600,
260 .uartclk = 14745600,
269 .uartclk = 14745600,
279 .uartclk = 921600 * 16,
288 .uartclk = 921600 * 16,
297 .uartclk = 921600 * 16,
|
| /Linux-v6.1/drivers/tty/serial/ |
| D | xilinx_uartps.c | 199 struct clk *uartclk; member
456 calc_baud = cdns_uart_calc_baud_divs(port->uartclk, baud, &bdiv, &cd, in cdns_uart_set_baud_rate()
531 port->uartclk = ndata->new_rate; in cdns_uart_clk_notifier_cb()
700 minbaud = port->uartclk / in cdns_uart_set_termios()
702 maxbaud = port->uartclk / (CDNS_UART_BDIV_MIN + 1); in cdns_uart_set_termios()
1191 if (port->uartclk && device->baud) { in cdns_early_console_setup()
1196 cdns_uart_calc_baud_divs(port->uartclk, device->baud, in cdns_early_console_setup()
1371 ret = clk_enable(cdns_uart->uartclk); in cdns_uart_resume()
1395 clk_disable(cdns_uart->uartclk); in cdns_uart_resume()
1415 clk_disable(cdns_uart->uartclk); in cdns_runtime_suspend()
[all …]
|
| D | mpc52xx_uart.c | 297 port->uartclk / (32 * 0xffff) + 1, in mpc5200_psc_set_baudrate()
298 port->uartclk / 32); in mpc5200_psc_set_baudrate()
299 divisor = (port->uartclk + 16 * baud) / (32 * baud); in mpc5200_psc_set_baudrate()
317 port->uartclk / (32 * 0xffff) + 1, in mpc5200b_psc_set_baudrate()
318 port->uartclk / 4); in mpc5200b_psc_set_baudrate()
319 divisor = (port->uartclk + 2 * baud) / (4 * baud); in mpc5200b_psc_set_baudrate()
556 port->uartclk / (16 * 0xffff) + 1, in mpc512x_psc_set_baudrate()
557 port->uartclk / 16); in mpc512x_psc_set_baudrate()
558 divisor = (port->uartclk + 8 * baud) / (16 * baud); in mpc512x_psc_set_baudrate()
894 port->uartclk / (16 * 0xffff) + 1, in mpc5125_psc_set_baudrate()
[all …]
|
| D | sccnxp.c | 311 div_std = DIV_ROUND_CLOSEST(port->uartclk, 2 * 16 * baud); in sccnxp_set_baud()
313 bestbaud = DIV_ROUND_CLOSEST(port->uartclk, 2 * 16 * div_std); in sccnxp_set_baud()
327 tmp_baud = DIV_ROUND_CLOSEST(port->uartclk, div_std); in sccnxp_set_baud()
886 int i, ret, uartclk; in sccnxp_probe() local
922 uartclk = 0; in sccnxp_probe()
934 uartclk = clk_get_rate(clk); in sccnxp_probe()
937 if (!uartclk) { in sccnxp_probe()
939 uartclk = s->chip->freq_std; in sccnxp_probe()
943 if ((uartclk < s->chip->freq_min) || (uartclk > s->chip->freq_max)) { in sccnxp_probe()
998 s->port[i].uartclk = uartclk; in sccnxp_probe()
|
| D | 21285.c | 265 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); in serial21285_set_termios()
267 b = port->uartclk / (16 * quot); in serial21285_set_termios()
368 if (ser->baud_base != port->uartclk / 16) in serial21285_verify_port()
402 serial21285_port.uartclk = mem_fclk_21285 / 4; in serial21285_setup_ports()
452 *baud = port->uartclk / (16 * (tmp + 1)); in serial21285_get_options()
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | hi3519.dtsi | 56 clock-names = "uartclk", "apb_pclk";
65 clock-names = "uartclk", "apb_pclk";
74 clock-names = "uartclk", "apb_pclk";
83 clock-names = "uartclk", "apb_pclk";
92 clock-names = "uartclk", "apb_pclk";
|
| D | arm-realview-eb.dtsi | 94 uartclk: uartclk@24M { label
373 clocks = <&uartclk>, <&pclk>;
374 clock-names = "uartclk", "apb_pclk";
380 clocks = <&uartclk>, <&pclk>;
381 clock-names = "uartclk", "apb_pclk";
387 clocks = <&uartclk>, <&pclk>;
388 clock-names = "uartclk", "apb_pclk";
394 clocks = <&uartclk>, <&pclk>;
395 clock-names = "uartclk", "apb_pclk";
|
| D | integratorcp.dts | 73 uartclk: uartclk@14.74M { label
249 clocks = <&uartclk>, <&pclk>;
250 clock-names = "uartclk", "apb_pclk";
255 clocks = <&uartclk>, <&pclk>;
256 clock-names = "uartclk", "apb_pclk";
279 clocks = <&uartclk>, <&pclk>;
|
| D | arm-realview-pb1176.dts | 104 uartclk: uartclk@24M { label
421 clocks = <&uartclk>, <&pclk>;
422 clock-names = "uartclk", "apb_pclk";
430 clocks = <&uartclk>, <&pclk>;
431 clock-names = "uartclk", "apb_pclk";
439 clocks = <&uartclk>, <&pclk>;
440 clock-names = "uartclk", "apb_pclk";
448 clocks = <&uartclk>, <&pclk>;
449 clock-names = "uartclk", "apb_pclk";
557 clocks = <&uartclk>, <&pclk>;
[all …]
|
| D | arm-realview-pbx.dtsi | 109 uartclk: uartclk@24M { label
371 clocks = <&uartclk>, <&pclk>;
372 clock-names = "uartclk", "apb_pclk";
378 clocks = <&uartclk>, <&pclk>;
379 clock-names = "uartclk", "apb_pclk";
385 clocks = <&uartclk>, <&pclk>;
386 clock-names = "uartclk", "apb_pclk";
564 clocks = <&uartclk>, <&pclk>;
565 clock-names = "uartclk", "apb_pclk";
|
| D | integratorap.dts | 75 uartclk: uartclk@14.74M { label
224 clocks = <&uartclk>, <&pclk>;
225 clock-names = "uartclk", "apb_pclk";
231 clocks = <&uartclk>, <&pclk>;
232 clock-names = "uartclk", "apb_pclk";
|
| /Linux-v6.1/arch/mips/ath25/ |
| D | devices.c | 74 void __init ath25_serial_setup(u32 mapbase, int irq, unsigned int uartclk) in ath25_serial_setup() argument
86 s.uartclk = uartclk; in ath25_serial_setup()
|
| /Linux-v6.1/arch/mips/mti-malta/ |
| D | malta-platform.c | 34 .uartclk = 1843200, \
50 .uartclk = 3686400, /* Twice the usual clk! */
|
| /Linux-v6.1/arch/arm/mach-s3c/ |
| D | mach-vr1000.c | 138 .uartclk = VR1000_BAUDBASE,
146 .uartclk = VR1000_BAUDBASE,
154 .uartclk = VR1000_BAUDBASE,
162 .uartclk = VR1000_BAUDBASE,
|
| /Linux-v6.1/arch/arm/mach-footbridge/ |
| D | isa.c | 52 .uartclk = 1843200,
60 .uartclk = 1843200,
|
| /Linux-v6.1/arch/mips/loongson2ef/common/ |
| D | serial.c | 25 .uartclk = clk, \
34 .uartclk = clk, \
|
| /Linux-v6.1/Documentation/devicetree/bindings/serial/ |
| D | nxp,lpc1850-uart.txt | 8 - clock-names : required elements: "uartclk", "reg".
27 clock-names = "uartclk", "reg";
|
| /Linux-v6.1/arch/mips/bcm47xx/ |
| D | serial.c | 44 p->uartclk = ssb_port->baud_base; in uart8250_init_ssb()
70 p->uartclk = bcma_port->baud_base; in uart8250_init_bcma()
|
