Home
last modified time | relevance | path

Searched refs:resistors (Results 1 – 25 of 37) sorted by relevance

12

/Linux-v6.1/drivers/rtc/
Drtc-ds1343.c147 char *diodes = "disabled", *resistors = " "; in ds1343_show_tricklecharger() local
166 resistors = "1k Ohm"; in ds1343_show_tricklecharger()
170 resistors = "2k Ohm"; in ds1343_show_tricklecharger()
174 resistors = "4k Ohm"; in ds1343_show_tricklecharger()
183 return sprintf(buf, "%s %s\n", diodes, resistors); in ds1343_show_tricklecharger()
Drtc-ds1305.c386 char *resistors = ""; in ds1305_proc() local
402 resistors = "2k Ohm"; in ds1305_proc()
405 resistors = "4k Ohm"; in ds1305_proc()
408 resistors = "8k Ohm"; in ds1305_proc()
417 seq_printf(seq, "trickle_charge\t: %s%s\n", diodes, resistors); in ds1305_proc()
/Linux-v6.1/drivers/gpu/drm/nouveau/nvkm/subdev/bios/
Diccsense.c122 rail->resistors[r].mohm = nvbios_rd08(bios, entry + res_start + r * 2); in nvbios_iccsense_parse()
123 rail->resistors[r].enabled = !(nvbios_rd08(bios, entry + res_start + r * 2 + 1) & 0x40); in nvbios_iccsense_parse()
/Linux-v6.1/drivers/gpu/drm/nouveau/include/nvkm/subdev/bios/
Diccsense.h13 struct pwr_rail_resistor_t resistors[3]; member
/Linux-v6.1/Documentation/hwmon/
Dina3221.rst48 value for their shunt resistors)
53 value for their shunt resistors)
Dltc4260.rst44 registers. If a set of voltage divider resistors is installed, calculate the
Dw83l785ts.rst25 of external resistors, so the user cannot change it. Values seen so
Dltc4261.rst44 registers. If a set of voltage divider resistors is installed, calculate the
Dltc2945.rst44 registers. If a set of voltage divider resistors is installed, calculate the
Dltc4245.rst49 rely on the sense resistors listed in Table 2: "Sense Resistor Values".
Dvt1211.rst84 external scaling resistors. This external scaling needs to be compensated for
89 The board level scaling resistors according to VIA's recommendation are as
Dlm85.rst99 The voltage inputs have internal scaling resistors so that the following
100 voltage can be measured without external resistors:
Df71805f.rst69 need external resistors. An exception is in0, which is used to monitor
Dpc87360.rst156 well as the values of the resistors used for division is left to the
/Linux-v6.1/Documentation/devicetree/bindings/gpio/
Dgpio-xra1403.txt5 - Internal pull-up resistors
/Linux-v6.1/Documentation/ABI/stable/
Dsysfs-class-udc63 Allows users to disconnect data pullup resistors thus causing a
/Linux-v6.1/arch/arm/mach-s3c/
DKconfig.s3c64xx210 resistors fitted so that the card detects for
219 resistors fitted so that the card detects for
/Linux-v6.1/arch/arm/boot/dts/
Dsun6i-a31s-yones-toptech-bs1078-v2.dts165 /* Voltage source for I2C pullup resistors for I2C Bus 0 */
Dda850-lego-ev3.dts248 /* Buttons have external pulldown resistors */
Dstm32mp15xx-dhcom-som.dtsi492 * SD bus pull-up resistors:
/Linux-v6.1/Documentation/devicetree/bindings/leds/
Dleds-lm3532.txt11 each with 32 internal voltage setting resistors, 8-bit logarithmic and linear
/Linux-v6.1/drivers/gpu/drm/nouveau/nvkm/subdev/iccsense/
Dbase.c261 struct pwr_rail_resistor_t *res = &pwr_rail->resistors[r]; in nvkm_iccsense_oneinit()
/Linux-v6.1/Documentation/devicetree/bindings/pinctrl/
Dbrcm,bcm11351-pinctrl.txt88 pull-up resistors (1.2k, 1.8k, 2.7k) available
177 - setting pull-up resistance to 720 Ohm (ie. enabling 1.2k and 1.8k resistors
/Linux-v6.1/Documentation/networking/device_drivers/can/
Dcan327.rst326 Your adapter may have resistors soldered in which are meant to terminate
331 termination resistors on its PCB and try removing them.
/Linux-v6.1/Documentation/arm/samsung-s3c24xx/
Dgpio.rst140 pull-up resistors enabled. This can be configured by the following

12