Searched refs:programmed (Results 1 – 25 of 150) sorted by relevance
123456
| /Linux-v6.1/Documentation/devicetree/bindings/input/ |
| D | ti,drv260x.txt | 16 - library-sel - These are ROM based waveforms pre-programmed into the IC.
19 DRV260X_LIB_EMPTY - Do not use a pre-programmed library
20 DRV260X_ERM_LIB_A - Pre-programmed Library
21 DRV260X_ERM_LIB_B - Pre-programmed Library
22 DRV260X_ERM_LIB_C - Pre-programmed Library
23 DRV260X_ERM_LIB_D - Pre-programmed Library
24 DRV260X_ERM_LIB_E - Pre-programmed Library
25 DRV260X_ERM_LIB_F - Pre-programmed Library
26 DRV260X_LIB_LRA - Pre-programmed LRA Library
|
| /Linux-v6.1/Documentation/ABI/testing/ |
| D | sysfs-driver-intel-m10-bmc-sec-update | 6 region if one is programmed, else it returns the
7 string: "hash not programmed". This file is only
16 reconfiguration region if one is programmed, else it
17 returns the string: "hash not programmed". This file
26 if one is programmed, else it returns the string:
27 "hash not programmed". This file is only visible if the
|
| D | sysfs-driver-tegra-fuse | 6 data programmed at the factory. The data is layed out in 32bit
|
| /Linux-v6.1/Documentation/misc-devices/ |
| D | spear-pcie-gadget.rst | 44 vendor_id returns programmed vendor id (hex)
45 device_id returns programmed device id(hex)
58 INTA, MSI or NO_INT). Select MSI only when you have programmed
63 vendor_id write vendor id(hex) to be programmed.
64 device_id write device id(hex) to be programmed.
102 check for programmed bar0 size::
|
| D | ad525x_dpot.rst | 9 settings. Access to the factory programmed tolerance is also provided, but
23 The tolerance files are the read-only factory programmed tolerance settings
|
| D | oxsemi-tornado.rst | 26 The oversampling rate is programmed with the TCR register and the clock
27 prescaler is programmed with the CPR/CPR2 register pair [OX200]_ [OX952]_
35 CPR/CPR2 register pair has to be programmed in the right order.
|
| /Linux-v6.1/drivers/slimbus/ |
| D | Kconfig | 21 programmed using Linux kernel.
32 Component is programmed using Linux kernel.
|
| /Linux-v6.1/Documentation/hwmon/ |
| D | g760a.rst | 22 The fan speed is programmed by setting the period via 'pwm1' of two
35 speed differs more than 20% with respect to the programmed fan speed;
|
| D | ina209.rst | 84 register is programmed correctly before they are used. Normally this is expected
89 programmed (ie has a value not equal to zero). If so, this value is retained.
91 programmed into the calibration register.
|
| D | g762.rst | 45 of the programmed value for over 6 seconds 'fan1_alarm' is
64 the fan speed is programmed by setting a value between 0 and 255 via 'pwm1'
|
| D | ds620.rst | 23 high and low temperature limits which can be user defined (i.e. programmed
|
| /Linux-v6.1/Documentation/driver-api/soundwire/ |
| D | stream.rst | 353 (3) Computed Bus and transport parameters are programmed in Master(s) and
359 (4) Once all the values are programmed, Bus initiates switch to alternate
360 bank where all new values programmed gets into effect.
385 (1) All the values computed in SDW_STREAM_PREPARED state are programmed
393 (3) Once all the values are programmed, Bus initiates switch to alternate
394 bank where all new values programmed gets into effect and port(s)
418 (2) All the current configuration of Bus and active stream(s) are programmed
421 (3) Once all the values are programmed, Bus initiates switch to alternate
422 bank where all new values programmed gets into effect and port(s) associated
|
| /Linux-v6.1/Documentation/devicetree/bindings/clock/ |
| D | silabs,si5341.txt | 21 chip at boot, in case you have a (pre-)programmed device. If the PLL is not
28 still be programmed into the chip and the driver will leave them "as is".
56 If these are not specified, and the PLL is not yet programmed when the driver
119 silabs,reprogram; /* Chips are not programmed, always reset */
|
| /Linux-v6.1/Documentation/trace/coresight/ |
| D | coresight-config.rst | 17 Many CoreSight components can be programmed in complex ways - especially ETMs.
43 and efficient for the feature to be programmed onto the device when required.
47 will be programmed into the device hardware.
56 feature being enabled that can adjust the behaviour of the operation programmed
59 For example, this could be a count value in a programmed operation that repeats
125 In this case 'strobing' is enabled & programmed into the ETMv4.
|
| /Linux-v6.1/drivers/mtd/chips/ |
| D | Kconfig | 162 A subset of them are pre-programmed at the factory with a
166 programmable (OTP) bits; when programmed, register bits cannot be
171 Lock Register bit is programmed, the associated Protection Register
172 can only be read; it can no longer be programmed. Additionally,
173 because the Lock Register bits themselves are OTP, when programmed,
|
| /Linux-v6.1/Documentation/devicetree/bindings/clock/ti/ |
| D | mux.txt | 11 as they are programmed into the regster. E.g:
22 Some clock controller IPs do not allow a value of zero to be programmed
|
| /Linux-v6.1/Documentation/leds/ |
| D | well-known-leds.txt | 23 The "player LEDs" are then programmed with a pattern to indicate a particular
24 player. For example, a game controller with 4 LEDs, may be programmed with "x---"
|
| /Linux-v6.1/Documentation/power/ |
| D | power_supply_class.rst | 154 constant charge current programmed by charger.
161 constant charge voltage programmed by charger.
166 input current limit programmed by charger. Indicates
169 input voltage limit programmed by charger. Indicates
172 input power limit programmed by charger. Indicates
|
| /Linux-v6.1/Documentation/i2c/busses/ |
| D | i2c-amd-mp2.rst | 18 The MP2 is an ARM processor programmed as an I2C controller and communicating
|
| /Linux-v6.1/Documentation/devicetree/bindings/fpga/ |
| D | fpga-region.txt | 32 * The entire FPGA is programmed.
59 * FPGA Bridges should be disabled while the FPGA is being programmed to
138 Region, the FPGA already has been programmed. A DTO that targets an FPGA Region
177 it indicates that the FPGA has already been programmed with this image.
192 programmed.
195 programmed.
197 FPGA to go to operating mode after the region has been programmed.
298 In this case, the FPGA will have one or more PRR's that may be programmed
|
| /Linux-v6.1/Documentation/devicetree/bindings/timer/ |
| D | jcore,pit.txt | 13 assignment to be programmed by software, but this property is
|
| D | snps,arc-timer.txt | 3 - Can be optionally programmed to interrupt on Limit
|
| /Linux-v6.1/drivers/staging/iio/Documentation/ |
| D | sysfs-bus-iio-adc-ad7280a | 8 enable for the programmed amount of time, before it
|
| /Linux-v6.1/Documentation/devicetree/bindings/pinctrl/ |
| D | ti,iodelay.txt | 4 for each pin. For most part the IO delay values are programmed by the bootloader,
|
| /Linux-v6.1/Documentation/devicetree/bindings/sound/ |
| D | fsl,ssi.txt | 4 be programmed in AC97, I2S, left-justified, or right-justified modes.
47 If specified, the SSI is to be programmed in asynchronous
|
123456
