Searched refs:operate (Results 1 – 25 of 188) sorted by relevance
12345678
| /Linux-v6.1/Documentation/mips/ |
| D | ingenic-tcu.rst | 29 operate.
35 - On the oldest SoCs (up to JZ4740), all of the eight channels operate in
37 - On JZ4725B, channel 5 operates as TCU2, the others operate as TCU1.
38 - On newest SoCs (JZ4750 and above), channels 1-2 operate as TCU2, the
39 others operate as TCU1.
|
| /Linux-v6.1/drivers/firmware/arm_scmi/ |
| D | Kconfig | 88 If you want the SCMI SMC based transport to operate in atomic
92 transport to optionally ask for atomic SCMI transactions and operate
128 If you want the SCMI VirtIO based transport to operate in atomic
133 transport to optionally ask for atomic SCMI transactions and operate
|
| /Linux-v6.1/Documentation/devicetree/bindings/serial/ |
| D | nxp,sc16is7xx.txt | 25 should operate in IrDA mode.
61 should operate in IrDA mode.
|
| /Linux-v6.1/Documentation/devicetree/bindings/mtd/ |
| D | microchip,mchp23k256.txt | 8 - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
|
| /Linux-v6.1/Documentation/sh/ |
| D | booting.rst | 9 inter-operate with old bootloaders must either use a builtin DTB or
|
| /Linux-v6.1/Documentation/scsi/ |
| D | bnx2fc.rst | 13 depend on the state of the network interfaces to operate. As such, the network
28 2. Configure the interfaces on which bnx2fc driver has to operate on.
|
| /Linux-v6.1/Documentation/devicetree/bindings/ipmi/ |
| D | aspeed,ast2400-ibt-bmc.txt | 19 interrupt, the driver will operate in poll mode.
|
| /Linux-v6.1/drivers/pci/endpoint/ |
| D | Kconfig | 14 controller that can operate in endpoint mode.
|
| /Linux-v6.1/drivers/usb/dwc2/ |
| D | Kconfig | 35 driver to operate in Host-only mode.
45 driver to operate in Peripheral-only mode. This option requires
|
| /Linux-v6.1/Documentation/devicetree/bindings/timer/ |
| D | ti,keystone-timer.txt | 6 timers, each half can operate in conjunction (chain mode) or independently
|
| D | ti,davinci-timer.txt | 6 timers, each half can operate in conjunction (chain mode) or independently
|
| /Linux-v6.1/Documentation/devicetree/bindings/net/can/ |
| D | tcan4x5x.txt | 12 operate at should be less than or equal to 18 MHz.
|
| /Linux-v6.1/Documentation/driver-api/ |
| D | mailbox.rst | 43 The client might want to operate in blocking mode (synchronously
106 dc_sync->cl.tx_done = NULL; /* operate in blocking mode */
|
| /Linux-v6.1/fs/sysfs/ |
| D | Kconfig | 16 Some system agents rely on the information in sysfs to operate.
|
| /Linux-v6.1/tools/io_uring/ |
| D | README | 17 io_uring-bench should operate on. This uses the raw io_uring
|
| /Linux-v6.1/Documentation/devicetree/bindings/media/ |
| D | samsung-s5k6a3.txt | 23 configured to operate, in Hz; if this property is not
|
| D | samsung-s5k5baf.txt | 23 configured to operate, in Hz; if this property is not
|
| /Linux-v6.1/Documentation/devicetree/bindings/cpufreq/ |
| D | cpufreq-st.txt | 7 the DT and operate in the usual way.
|
| /Linux-v6.1/Documentation/i2c/busses/ |
| D | i2c-taos-evm.rst | 47 to operate at 1200 bps. However, I don't think this is a big concern in
|
| /Linux-v6.1/drivers/net/wireless/ath/wil6210/ |
| D | Kconfig | 24 ISR registers on wil6210 chip may operate in either
|
| /Linux-v6.1/Documentation/devicetree/bindings/net/ |
| D | micrel.txt | 40 - micrel,fiber-mode: If present the PHY is configured to operate in fiber mode
|
| /Linux-v6.1/arch/m68k/ |
| D | Kconfig.bus | 54 operate ISA cards on Atari. Only 8 bit cards are supported, and
|
| /Linux-v6.1/Documentation/hwmon/ |
| D | ads7828.rst | 56 It can operate in single ended mode (8 +ve inputs) or in differential mode,
|
| /Linux-v6.1/Documentation/power/ |
| D | opp.rst | 70 As the system proceeds to operate, SoC framework may choose to make certain
77 operational functions operate only on available opps:
152 /* dont operate on the pointer.. just do a sanity check.. */
347 for the OPP library to operate on. Pointer to this structure is
|
| /Linux-v6.1/Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-vt8500.txt | 3 These SoCs contain a combined Pinmux/GPIO module. Each pin may operate as
|
12345678
