Searched refs:_HID (Results 1 – 17 of 17) sorted by relevance
21 Name (_HID, ...)24 Name (_HID, ...)37 Name (_HID, ...)52 Name (_HID, ...)
122 | | +-| _HID | Name(_HID, "PNP0C0D"): the hardware ID134 | +-| _HID | Name(_HID, "PNP0A08"): the hardware ID178 | | +-| _HID | Name(_HID, "PNP0A0B"): the hardware ID212 | N | Device | xSDT | _HID |267 _HID:268 _HID in the last column of the table means that the object's bus_id269 is derived from the _HID/_CID identification objects present under272 used to retrieve the _HID and _CIDs of that object.279 bus_id cannot be determined from _HID/_CID of the corresponding281 example, it may be a PCI device with _ADR defined and without _HID
467 Moreover, the specification mandates that either a _HID or an _ADR identification469 6.0). For non-enumerable bus types that object must be _HID and its value must475 if PRP0001 is returned by _HID, the ACPI subsystem will look for the491 _HID and _CID depends on the position of PRP0001 in the _CID return package.492 Specifically, the device IDs returned by _HID and preceding PRP0001 in the _CID494 will be enumerated to depends on the device ID returned by _HID.502 Name (_HID, "PRP0001")522 It is valid to define device objects with a _HID returning PRP0001 and without528 However, PRP0001 can only be returned from either _HID or _CID of a device
66 Name (_HID, "SONY319A")
19 Name (_HID, ...)217 In those cases ACPI device identification objects, _HID, _CID, _CLS, _SUB, _HRV,265 Name (_HID, ...)
121 Name (_HID, "INTC105C")
21 #define CIO2_SENSOR_CONFIG(_HID, _NR, ...) \ argument23 .hid = _HID, \28 #define NODE_SENSOR(_HID, _PROPS) \ argument30 .name = _HID, \
39 如果操作系统要管理一个通过ACPI描述的不可发现的设备，该设备将有一个特定的_HID/_CID，以80 系统固件必须为每个设备提供一个_HID对象...以使OSPM能够做到这一点。118 主板资源将出现在ACPI命名空间的根部（在_SB下），在一个节点的_HID为EISAID（PNP0C0
19 CCCCCCCC contains device object's PNPID (_HID or _CID).25 This attribute indicates the hardware ID (_HID) of the27 This file is present for device objects having the _HID
55 Name (_HID, "<Vendor-Specific HID>") // Vendor-Specific HID61 Name (_HID, "IPMB0001") // IPMB device interface
222 and define processor container devices (_HID ACPI0010, Section 8.4,457 _CID 6.1.2 Use as needed, see also _HID.459 _CLS 6.1.3 Use as needed, see also _HID.503 _HID 6.1.5 This is the primary object to use in device probing,510 _LPI 8.4.4.3 Recommended for use with processor definitions (_HID563 _RDI 8.4.4.4 Recommended for use with processor definitions (_HID584 _SUB 6.1.9 Use as needed; _HID or _CID are preferred.614 Processors should now be defined as Device objects with _HID ACPI0007; do617 Devices (see Section 8.4.3.1, _HID ACPI0010); do not use processor aggregator
40 ACPI, that device will have a specific _HID/_CID that tells the OS what103 system firmware must supply an _HID object ... for each device to158 namespace (under \_SB) in a node with a _HID of EISAID (PNP0C02), and
85 Name(_HID, "NXP0006")
33 Name (_HID, "BMA222E")
22 We experimented with probing the ACPI interface _HID (Hardware ID)/_CID25 In fact, it appeared to be an m:n mapping between the _HID and actual
48 _HID matching one of the entries in the table.
105 If the firmware supports hotplug of NUMA nodes, it defines an object _HID
