Searched refs:VDD (Results 1 – 25 of 46) sorted by relevance
12
| /Linux-v6.1/Documentation/devicetree/bindings/sound/ |
| D | everest,es7134.txt | 7 - VDD-supply : regulator phandle for the VDD supply
14 VDD-supply = <&vcc_5v>;
|
| D | img,pistachio-internal-dac.txt | 10 - VDD-supply : Digital power supply regulator (+1.8V or +3.3V)
17 VDD-supply = <&supply3v3>;
|
| D | rt5645.txt | 41 1 : Mode-0 (VDD=3.3V), two port jack detection
42 2 : Mode-1 (VDD=3.3V), one port jack detection
43 3 : Mode-2 (VDD=1.8V), one port jack detection
|
| D | da7218.txt | 11 - VDD-supply: VDD power supply for the device
60 - dlg,jack-threshold-pct : Threshold level for jack detection (% of VDD)
77 VDD-supply = <®_audio>;
|
| D | da7219.txt | 15 - VDD-supply: VDD power supply for the device
83 VDD-supply = <®_audio>;
|
| /Linux-v6.1/Documentation/devicetree/bindings/opp/ |
| D | ti-omap5-opp-supply.txt | 19 - vdd-supply: phandle to regulator controlling VDD supply
25 "ti,omap-opp-supply" - basic OPP supply controlling VDD and VBB
26 "ti,omap5-opp-supply" - OMAP5+ optimized voltages in efuse(class0)VDD
28 "ti,omap5-core-opp-supply" - OMAP5+ optimized voltages in efuse(class0) VDD
|
| /Linux-v6.1/Documentation/hwmon/ |
| D | smm665.rst | 76 power supply channels as well as VDD, 12V input, two general-purpose analog
117 in2_input 3.3V (VDD) input voltage (mV)
128 in2_min 3.3V (VDD) input minimum voltage (mV)
139 in2_max 3.3V (VDD) input maximum voltage (mV)
150 in2_lcrit 3.3V (VDD) input critical minimum voltage (mV)
161 in2_crit 3.3V (VDD) input critical maximum voltage (mV)
172 in2_crit_alarm 3.3V (VDD) input critical alarm
|
| D | ltc2945.rst | 56 SENSE+ or VDD pin depending on chip configuration.
83 power1_input Power (in uW). Power is calculated based on SENSE+/VDD
|
| D | w83795.rst | 52 24 3VDD 1Ch in12
108 18 3VDD 1Ch in12
|
| D | gl518sm.rst | 61 zero'; this is important for negative voltage measurements. The VDD input
|
| /Linux-v6.1/drivers/hwmon/ |
| D | gl518sm.c | 238 show(VDD, in_input0, voltage_in[0]);
242 show(VDD, in_min0, voltage_min[0]);
246 show(VDD, in_max0, voltage_max[0]);
329 set_low(VDD, in_min0, voltage_min[0], GL518_REG_VDD_LIMIT);
333 set_high(VDD, in_max0, voltage_max[0], GL518_REG_VDD_LIMIT);
|
| /Linux-v6.1/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-thermocouple | 10 than VDD, otherwise '0'.
|
| /Linux-v6.1/arch/arm64/boot/dts/mediatek/ |
| D | mt8183-kukui-audio-da7219.dtsi | 19 VDD-supply = <&pp1800_alw>;
|
| /Linux-v6.1/drivers/phy/qualcomm/ |
| D | phy-qcom-usb-hs-28nm.c | 40 VDD, enumerator
344 priv->vregs[VDD].supply = "vdd"; in qcom_snps_hsphy_probe()
|
| /Linux-v6.1/arch/arm64/boot/dts/hisilicon/ |
| D | hikey970-pmic.dtsi | 78 ldo34: ldo34 { /* GPS AUX IN VDD */
|
| /Linux-v6.1/Documentation/devicetree/bindings/input/rmi4/ |
| D | rmi_i2c.txt | 27 - vdd-supply: VDD power supply.
|
| /Linux-v6.1/arch/mips/boot/dts/img/ |
| D | pistachio_marduk.dts | 76 VDD-supply = <&internal_dac_supply>;
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | at91-sama5d4_ma5d4evk.dts | 159 regulator-name = "VDD MCI1";
|
| D | ste-ux500-samsung-gavini.dts | 265 /* VDD 3V */
473 /* Used for VDD for sensors */
474 regulator-name = "V-SENSORS-VDD";
584 /* VDD is "digital supply" 1.71-3.47V */
|
| D | ste-ux500-samsung-janice.dts | 255 /* VDD 3V */
540 /* Used for VDD for sensors */
541 regulator-name = "V-SENSORS-VDD";
671 /* VDD is "digital supply" 1.71-3.47V */
|
| D | at91-nattis-2-natte-2.dts | 38 regulator-name = "panel-VDD";
|
| D | at91-sama5d4_xplained.dts | 292 regulator-name = "VDD MCI1";
|
| D | sun8i-h3-orangepi-pc.dts | 188 * The datasheet uses 1.1V as the minimum value of VDD-CPUX,
|
| /Linux-v6.1/drivers/iio/adc/ |
| D | lp8788_adc.c | 145 [LPADC_VDD] = LP8788_CHAN(VDD, IIO_VOLTAGE),
|
| /Linux-v6.1/Documentation/w1/slaves/ |
| D | w1_ds2438.rst | 83 battery input (VDD)
|
12
