Home
last modified time | relevance | path

Searched refs:SCI (Results 1 – 19 of 19) sorted by relevance

/Linux-v6.1/arch/sh/kernel/cpu/sh3/
Dsetup-sh770x.c29 DMAC, SCIF0, SCIF2, SCI, ADC_ADI, enumerator
40 INTC_VECT(SCI, 0x4e0), INTC_VECT(SCI, 0x500),
41 INTC_VECT(SCI, 0x520), INTC_VECT(SCI, 0x540),
69 { 0xfffffee4, 0, 16, 4, /* IPRB */ { WDT, REF, SCI, 0 } },
/Linux-v6.1/Documentation/ABI/testing/
Dsysfs-firmware-acpi100 the System Control Interrupt (SCI), which appears
105 special driver support. So while the SCI handles a few
119 To figure out where all the SCI's are coming from,
169 sci The number of times the ACPI SCI
172 sci_not The number of times the ACPI SCI
175 gpe_all count of SCI caused by GPEs.
/Linux-v6.1/drivers/soc/ti/
DKconfig54 tristate "TI SCI PM Domains Driver"
59 the TI SCI protocol.
/Linux-v6.1/drivers/clk/keystone/
DKconfig24 Forces the TI SCI clock driver to probe available clocks from the
/Linux-v6.1/arch/arm64/boot/dts/ti/
Dk3-am62.dtsi71 <0x00 0x44043000 0x00 0x44043000 0x00 0x00000fe0>, /* TI SCI DEBUG */
Dk3-am64.dtsi87 <0x00 0x44043000 0x00 0x44043000 0x00 0x00000fe0>, /* TI SCI DEBUG */
Dk3-am62a.dtsi72 <0x00 0x44043000 0x00 0x44043000 0x00 0x00000fe0>, /* TI SCI DEBUG */
/Linux-v6.1/arch/arm/boot/dts/
Dintegratorap-im-pd1.dts56 /* Also used for the Smart Card Interface SCI */
/Linux-v6.1/Documentation/arm64/
Dacpi_object_usage.rst655 APEI requires the equivalent of an SCI and an NMI on ARMv8. The SCI is used
661 Since there is no direct equivalent of the x86 SCI or NMI, arm64 handles
662 these slightly differently. The SCI is handled as a high priority interrupt;
/Linux-v6.1/Documentation/admin-guide/
Ddevices.txt1293 74 char SCI bridge
1294 0 = /dev/SCI/0 SCI device 0
1295 1 = /dev/SCI/1 SCI device 1
1298 Currently for Dolphin Interconnect Solutions' PCI-SCI
2672 8 = /dev/ttySC0 SCI serial port (SuperH) - port 0
2673 9 = /dev/ttySC1 SCI serial port (SuperH) - port 1
2674 10 = /dev/ttySC2 SCI serial port (SuperH) - port 2
2675 11 = /dev/ttySC3 SCI serial port (SuperH) - port 3
/Linux-v6.1/drivers/reset/
DKconfig259 tristate "TI System Control Interface (TI-SCI) reset driver"
/Linux-v6.1/Documentation/x86/x86_64/
Dboot-options.rst197 Set up ACPI SCI interrupt.
/Linux-v6.1/drivers/tty/serial/
DKconfig643 tristate "SuperH SCI(F) serial port support"
649 int "Maximum number of SCI(F) serial ports" if EXPERT
658 bool "Support for console on SuperH SCI(F)" if EXPERT
664 bool "Support for early console on SuperH SCI(F)" if EXPERT
/Linux-v6.1/Documentation/watchdog/
Dwatchdog-parameters.rst310 0 = RESET(*) 1 = SMI 2 = NMI 3 = SCI
/Linux-v6.1/Documentation/userspace-api/ioctl/
Dioctl-number.rst297 'w' all CERN SCI driver
/Linux-v6.1/drivers/spi/
DKconfig872 tristate "SuperH SCI SPI controller"
876 SPI driver for SuperH SCI blocks.
/Linux-v6.1/drivers/acpi/
DKconfig445 SCI, mainly the corrected errors.
/Linux-v6.1/arch/x86/
DKconfig2832 bool "OLPC XO-1 SCI extras"
2837 Add support for SCI-based features of the OLPC XO-1 laptop:
2846 bool "OLPC XO-1.5 SCI extras"
2850 Add support for SCI-based features of the OLPC XO-1.5 laptop:
/Linux-v6.1/Documentation/power/
Dpci.rst236 Control Interrupt (SCI) to notify the kernel of the event. Then, the SCI